1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Prepare for cleaning. These steps cover Ultra 1000 Premium product code NB07500-1008. For another Ultra 1000 product code, follow the cleaning instructions supplied with that exact pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly or pitcher from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade onto the motor base, then gently push and twist to start; turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Switch off and unplug the motor base Wait until every moving part has stopped, then remove the cup and easy-twist extractor-blade assembly before cleaning.
2. Fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap
3. Attach the easy-twist extractor blade, refit the sealed cup assembly, reconnect power and blend for 20–30 seconds.
4. Stop, unplug and wait for all moving parts to stop before removing the assembly. Scrub away the loosened food with soap and water.
5. Dry the easy-twist extractor blade completely after every use. Check its underside for cracking or breakage and replace a damaged blade immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. These instructions apply to NutriBullet 1000 Series N10-0807DG. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the sealed cup and blade assembly on the motor base and blend for about 20–30 seconds to loosen dried food.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Prepare for cleaning. These steps cover Turbo 1000 product code NBT07400-1006AK. For NBT07400-1004AW or NBT07400-1006AW, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Take the blender apart for cleaning. These steps cover the black 1000 Series Mega Pack, product code N10-1107AK. For another pack code, match the cleaning method to the guide supplied with it; use the Milling Blade steps only when that blade is included. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 12 Piece pack, product code N12-1207C, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 10 Piece pack, product code N12-1007, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and gently turn clockwise to start the automatic cycle; turn the cup anticlockwise to stop after 20–30 seconds.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Unplug the motor base and wait until all moving parts stop. Remove the cup and extractor-blade assembly, then separate them.
2. Fill the cup about two-thirds full with water at 21°C or below and screw the extractor blade on tightly
3. Reconnect power Place the sealed cup and blade assembly on the motor base, gently push down and twist to start. Blend for about 20–30 seconds.
4. Gently push down and turn the cup anticlockwise to stop Unplug and wait until all movement stops, then remove and open the assembly normally. Lightly scrub away the loosened food and rinse.
5. Hand-wash the extractor blade with warm soapy water without removing its gasket Turn the blade on its side in a dish drainer so both sides dry completely.
6. Wipe the unplugged motor base with a warm, soapy damp cloth.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

1. Prepare to clean. These steps cover the cup and blade of Select 1000 product code NB07200-1007DG. For the Select 1000 with pitcher, product code NB07200-1006DG, use its supplied pitcher instructions. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Find the full product code on the appliance label.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Find the full product code on the appliance label.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Prepare for cleaning. These steps cover Ultra 1200 McLaren product code NB07500-1206GO-MC. For Club Pack product code NB07500-1214S, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Loosen dried food in a cup. Fill the cup halfway with soapy water and twist on the blade. Place the cup-and-blade assembly onto the Motor Base, reconnect power, then press down and twist clockwise to blend for 10–20 seconds. Twist anticlockwise to stop, unplug and wait for the blade to stop. Remove the assembly and untwist the blade; empty the water, lightly scrub away remaining debris and rinse.
2. Wash the cups and Batchbowl. Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse.
3. Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
4. Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.

1. Run the initial cleaning cycle. With the NutriBullet Baby Steam + Blend off and cool, fill the Water Reservoir to the 25-minute line with water and lock its cap clockwise. Fit the Blending Blade vertically onto the Blade Holder, lock the Work Bowl Lid clockwise and lock the Work Bowl anticlockwise onto the Motor Base. Connect power, turn the Setting Dial to Steam and press Power. The indicator flashes blue during steaming; five beeps mark completion. Unplug and let the appliance cool completely, then lift the blade vertically out using a mitt and discard remaining water from the Work Bowl and Water Reservoir.
2. Prepare Steam + Blend for cleaning. Turn off and unplug the NutriBullet Baby Steam + Blend, then let it cool completely before handling or cleaning parts.
3. Open and separate the used bowl. Allow at least ten minutes for cooling and wait until the appliance is completely cool and all moving parts have stopped. With the appliance unplugged, turn the Work Bowl clockwise off the base. Open the lid and turn its circular bottom grip anticlockwise to separate the lid into two pieces; remove trapped food or water and dry those pieces fully. Lift the Blending Blade vertically out by a non-sharp area using a mitt.
4. Empty and clean the reservoir and blade stem. Remove food from the Work Bowl, untwist the Water Reservoir Cap and discard remaining water. Use a cloth or soft-bristled brush to clear food from the bowl and inside the lid. Clean inside the Blade Stem to remove food or water, then dry it completely.
5. Rinse food away. Rinse the Work Bowl, Work Bowl Lid and Blending Blade under running water after use, holding the sharp blade by a non-sharp area. Clean the blade after every blend so food and mineral residue cannot build up.

Next steps

1. Wash the Work Bowl and lid. Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasher.
2. Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.
3. Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use.
4. Descale the Water Reservoir. Empty the Water Reservoir. Use a suitable chemical-free descaler or pour in 240 mL white vinegar. Leave the vinegar for at least 30 minutes, up to 24 hours according to the buildup, then discard it. Rinse with cool water and empty the loosened scale into the sink.
5. Store Steam + Blend. Unplug the appliance when it will not be used for a while. Keep all pieces together and store the assembled NutriBullet Baby Steam + Blend in a safe, dry, cool place.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Find the full product code on the appliance label.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.