1. Unpack the parts before first use, then separate the Blade Adapter, Chopping Blade, Dough Blade and Slice/Shred Disc from the Work Bowl. Wash the Pitcher and Lid, Work Bowl and Lid, Cups, To-Go Lids, Food Pusher, Blade Adapter and blade attachments with soap and water or in the dishwasher; avoid the heat/sanitise cycle. Hand-wash the Tamper, and clean the Extractor Blade with a small brush or sponge dampened in soapy water.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Do not run an empty Pitcher.
5. Press the Pitcher Lid firmly into place with the spout closed. Press the Lid Cap into the opening and twist until locked.

Next steps

1. Place the Pitcher on the unplugged Motor Base and twist clockwise until you hear a click.
2. Plug in the Motor Base; the Control Panel displays the blender menu.
3. Press Purée, Frozen Drinks, Smoothie or Nutmilk for a preset cycle, or choose Low, Medium or High. For Pulse, press and release for short bursts.
4. Once blending has stopped, switch off, unplug and wait for all movement to stop. Twist the Pitcher anticlockwise until it clicks free, then lift it off. Unlatch the spout Lid to pour, or push up the tab above the handle to remove the main Lid.
5. Keep each Cup blend to one minute or less. Do not run consecutive one-minute cycles; allow the contents to settle for at least 10–15 minutes before another cycle.

1. Fit and use the single-serve Cup.
   1. For single-serve blending, add cold or room-temperature ingredients and liquid to the Cup, below its MAX line. Keep hot, warm and carbonated ingredients out of the sealed Cup.
   2. Hand-tighten the Extractor Blade onto the Cup until sealed; never put a bare blade attachment on the base.
   3. Turn the Cup upside down, set it on the Motor Base and twist clockwise to lock it in place.
   4. Plug in the base; locking the Cup illuminates the single-serve menu. Select Frozen Drinks, Smoothie or Dressing, or a Low, Medium or High speed.
   5. Stop blending and wait until the blades are still. Switch off and unplug, then turn the Cup anticlockwise to unlock it before lifting it off; keep it upright before carefully untwisting the blade, pointing the opening away from your body.
   6. For stored drinks, remove the blade and fit a To-Go Lid; do not leave blended food sealed under the blade attachment.
2. Use the food processor attachments.
   1. For chopping, fit the Blade Adapter over the Work Bowl central shaft and push down; lower the Chopping Blade onto the adapter, holding only its centre plastic area.
   2. Remove seeds, stems and other inedible pieces, cut large food into 1–2 inch pieces, and add to the Work Bowl below MAX.
   3. Set the Work Bowl on the unplugged base and twist clockwise to the click. Only then fit the Work Bowl Lid, turn clockwise until its arrows align, and insert the Food Pusher; this order is needed for the interlock.
   4. Plug in to display the food processor menu. Select Chop for toppings or mixes, Dip for chunky spreads, or Low, Medium or High; hold Pulse only for controlled chopping.
   5. To add liquid, turn the Pusher Cap clockwise and remove the Inner Pusher, pour through the small chute without exceeding Work Bowl MAX, then replace the Inner Pusher.
   6. Stop, unplug and wait for the blade to stop. Turn the Work Bowl Lid anticlockwise and remove it before trying to unlock the bowl from the base; then turn the bowl anticlockwise, remove the blade by its plastic centre, and transfer food with a spoon or spatula.
   7. For dough, put the Blade Adapter on the Work Bowl shaft, fit the Dough Blade and add the prepared ingredients. Lock the Work Bowl onto the unplugged base, then lock the Lid with its arrows aligned and fit the Food Pusher.
   8. Plug in and Pulse a few times to distribute the wet and dry ingredients. Once dough begins to form, use Dough or Low; do not use a higher speed, which can overwork it.

   Next steps

   1. When kneaded, stop and unplug, wait for the Dough Blade to stop, unlock the Lid anticlockwise, unlock and remove the Work Bowl, then carefully lift out the Dough Blade.
   2. For slicing or shredding, fit the Blade Adapter and hold the reversible Disc by its centre knob. Put the desired slice or shred face upwards and align the Disc and adapter markings so the Disc sits in the higher operating position; lift and rotate it if it sits in the lower storage position.
   3. Twist the Work Bowl clockwise onto the unplugged base until it clicks, then fit and lock the Lid with the arrows aligned and insert the Food Pusher. Plug in and select High.
   4. With the motor running, remove the Inner Pusher for the small chute or remove the complete Food Pusher for the large chute. Guide food with the matching pusher; never use fingers or utensils, force food or overload the chute.
   5. Stop, unplug and wait for the Disc to stop. Unlock the Lid first, then unlock the Work Bowl, remove the Disc by its centre and use a spoon or spatula to remove food.
   6. Remove the blades or Disc and Blade Adapter before washing the Work Bowl and its Lid. Rinse away food, then hand-wash or use the dishwasher without a heat/sanitise cycle; also rinse and wash the adapter, blade attachments and Food Pusher.
   7. For storage, put the Blade Adapter on the Work Bowl shaft, followed by the Chopping Blade, Dough Blade and Slice/Shred Disc in its lower position, then fit the Lid so no cutting edges remain exposed.
3. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Lid and Vented Lid Cap securely fitted, keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • To add ingredients during blending, use only the Vented Lid Cap opening, then replace the cap; keep the main Pitcher Lid and Easy-Pour Spout closed. Only use the supplied Tamper to move food towards the blade.
4. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
   • Clean the Extractor Blade promptly with a small brush or sponge and soapy water, then dry it completely. Do not remove its components or gasket; replace a loose or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
   • Hand-wash the Tamper with soap and water; scrub stubborn food with a dish brush or sponge.
   • Rinse the Cups and To-Go Lids, brush off debris and place them on the top dishwasher rack without heat/sanitise, or hand-wash them.
   • To loosen dried food, add room-temperature water and 1–2 drops of dish soap. Fill the Cup to MAX and fit its blade, or half-fill the Pitcher and refit its Lid and cap. Blend for 20–30 seconds, stop and unplug, then scrub away the loosened residue and rinse.

   Next steps

   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.
   • Replace the Extractor Blade about every six months, or sooner if its condition or frequency of use requires it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Unpack the parts before first use, then wash the Pitcher, Cups and To-Go Lids with soap and water. The Pitcher is dishwasher-safe and Cups and To-Go Lids go on the top rack; do not use the heat/sanitise cycle. Hand-wash the Tamper and Easy-Twist Extractor Blade, keeping fingers clear of the cutting edges.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Observe the separate liquid and solid MAX lines. Do not run an empty Pitcher.
5. Fit the Pitcher Lid with the Vented Lid Cap attached and align the Lid with the handle.

Next steps

1. Set the Pitcher on the Motor Base with its handle to the right of the controls, never towards the back, then twist clockwise until it clicks. If left-handed, start with the handle towards the centre of the controls.
2. Plug in the Motor Base. Press POWER to illuminate the Control Panel.
3. Choose LOW, MEDIUM, HIGH, or the automatic EXTRACT cycle. The selected button illuminates; EXTRACT stops at the end of its cycle.
4. Press the selected speed or POWER to stop; the POWER light stays on in idle mode. Wait until the blades stop, press POWER to switch off fully and unplug, then twist the Pitcher anticlockwise and lift it off to pour.
5. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.

1. Fit and use the single-serve Cup.
   1. For single-serve blending, add cold or room-temperature ingredients and liquid to the Cup, below its MAX line. Keep hot, warm and carbonated ingredients out of the sealed Cup.
   2. Hand-tighten the Extractor Blade onto the Cup until sealed; never put a bare blade attachment on the base.
   3. Turn the Cup upside down, set it on the Motor Base and twist clockwise to lock it in place.
   4. Plug in, press POWER, then select a speed or EXTRACT.
   5. Stop blending and wait until the blades are still. Switch off and unplug, then turn the Cup anticlockwise to unlock it before lifting it off; keep it upright before carefully untwisting the blade, pointing the opening away from your body.
   6. For stored drinks, remove the blade and fit a To-Go Lid; do not leave blended food sealed under the blade attachment.
2. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Lid and Vented Lid Cap securely fitted, keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • For cold mixtures, switch to LOW and remove only the lid cap to add ingredients; leave the main Lid fitted. Use only the supplied Tamper, then replace the cap before raising the speed. Do not add through this opening while blending hot ingredients.
3. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
   • Clean the Extractor Blade promptly with a small brush or sponge and soapy water, then dry it completely. Do not remove its components or gasket; replace a loose or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
   • Hand-wash the Tamper with soap and water; scrub stubborn food with a dish brush or sponge.
   • Rinse the Cups and To-Go Lids, brush off debris and place them on the top dishwasher rack without heat/sanitise, or hand-wash them.
   • To loosen dried food, add room-temperature water and 1–2 drops of dish soap. Fill the Cup or Pitcher to its liquid MAX line and fit the blade or Pitcher Lid with its Vented Lid Cap. Blend for 20–30 seconds, stop and unplug, then scrub away the loosened residue and rinse.

   Next steps

   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.
   • Replace the Extractor Blade about every six months, or sooner if its condition or frequency of use requires it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Unpack the parts before first use, then wash the Pitcher, Cups and To-Go Lids with soap and water. The Pitcher is dishwasher-safe and Cups and To-Go Lids go on the top rack; do not use the heat/sanitise cycle. Hand-wash the Tamper and Easy-Twist Extractor Blade, keeping fingers clear of the cutting edges.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Observe the separate liquid and solid MAX lines. Do not run an empty Pitcher.
5. Press the Pitcher Lid firmly into place with the spout closed. Press the Lid Cap into the opening and twist until locked.

Next steps

1. Place the Pitcher on the unplugged Motor Base and twist clockwise until you hear a click. The Control Panel stays dark if the Pitcher or Lid is not fully secured.
2. Plug in the Motor Base. Press POWER to illuminate the Control Panel.
3. Select LOW, MEDIUM, HIGH, PULSE, or a program: Smoothies, Frozen Drinks, Purées or pitcher-only Soups.
4. Press the active speed or program to pause; both the motor and timer pause. Press it again to resume, or press POWER to stop and return to standby. Wait for the blades to stop, press POWER again to turn the display off, unplug, then twist the Pitcher anticlockwise and lift it off. Push up the tab by the handle to loosen the Lid.
5. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.

1. Fit and use the single-serve Cup.
   1. For single-serve blending, add cold or room-temperature ingredients and liquid to the Cup, below its MAX line. Keep hot, warm and carbonated ingredients out of the sealed Cup.
   2. Hand-tighten the Extractor Blade onto the Cup until sealed; never put a bare blade attachment on the base.
   3. Turn the Cup upside down, set it on the Motor Base and twist clockwise to lock it in place.
   4. Plug in and press POWER, then choose a manual speed or an available Cup program. Soups is a Pitcher-only program.
   5. Stop blending and wait until the blades are still. Switch off and unplug, then turn the Cup anticlockwise to unlock it before lifting it off; keep it upright before carefully untwisting the blade, pointing the opening away from your body.
   6. For stored drinks, remove the blade and fit a To-Go Lid; do not leave blended food sealed under the blade attachment.
2. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Lid and Vented Lid Cap securely fitted, keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • For cold mixtures, switch to LOW and remove only the lid cap to add ingredients; leave the main Lid fitted. Use only the supplied Tamper, then replace the cap before raising the speed. Do not add through this opening while blending hot ingredients.
3. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
   • Clean the Extractor Blade promptly with a small brush or sponge and soapy water, then dry it completely. Do not remove its components or gasket; replace a loose or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
   • Hand-wash the Tamper with soap and water; scrub stubborn food with a dish brush or sponge.
   • Rinse the Cups and To-Go Lids, brush off debris and place them on the top dishwasher rack without heat/sanitise, or hand-wash them.
   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.

   Next steps

   • Replace the Extractor Blade about every six months, or sooner if its condition or frequency of use requires it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Unpack the Motor Base and attachments onto a flat, dry surface. Rinse the Pitcher, Pitcher Lid and Vented Lid Cap; hand-wash in warm, soapy water or use a dishwasher without the sanitise cycle.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings. Press the rubber suction feet onto the surface so the base is stable.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Observe the separate liquid and solid MAX lines. Do not run an empty Pitcher.
5. Fit the Pitcher Lid with its Vented Lid Cap attached, aligning the rear loop opposite the spout with the Pitcher handle.

Next steps

1. Lower the Pitcher straight onto the Motor Base, aligning the Pitcher studs with the base grooves; listen for the click.
2. Plug in the Motor Base. Press POWER; the blending mode lights illuminate from left to right.
3. Press LOW, MED or HIGH once for continuous blending, or choose SMOOTHIE for the timed cycle. Hold PULSE only for as long as you want the blades to run.
4. Press POWER to stop blending and wait until the blades stop; the POWER light remains on in idle mode. Press POWER again to switch off completely, unplug, lift the Pitcher off the base and remove the Lid before pouring.
5. Never blend longer than one minute, and do not run consecutive cycles exceeding one minute in total.

1. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Lid and Vented Lid Cap securely fitted, keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • For a cold mixture, switch to LOW and remove only the Vented Lid Cap to add ingredients. Refit the cap before raising the speed; do not add through the opening while blending hot ingredients.
2. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.

1. Unpack the parts before first use, then wash the Pitcher, Cups and To-Go Lids with soap and water. The Pitcher is dishwasher-safe and Cups and To-Go Lids go on the top rack; do not use the heat/sanitise cycle. Hand-wash the Tamper and Easy-Twist Extractor Blade, keeping fingers clear of the cutting edges.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Observe the separate liquid and solid MAX lines. Do not run an empty Pitcher.
5. Fit the Pitcher Lid with the Vented Lid Cap attached and align the Lid with the handle.

Next steps

1. Set the Pitcher on the Motor Base with its handle to the right of the controls, never towards the back, then twist clockwise until it clicks. If left-handed, start with the handle towards the centre of the controls.
2. Plug in the Motor Base. Press POWER to illuminate the Control Panel.
3. Choose LOW, HIGH, or the automatic EXTRACT cycle. The selected button illuminates; EXTRACT stops at the end of its cycle.
4. Press the selected speed or POWER to stop; the POWER light stays on in idle mode. Wait until the blades stop, press POWER to switch off fully and unplug, then twist the Pitcher anticlockwise and lift it off to pour.
5. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.

1. Fit and use the single-serve Cup.
   1. For single-serve blending, add cold or room-temperature ingredients and liquid to the Cup, below its MAX line. Keep hot, warm and carbonated ingredients out of the sealed Cup.
   2. Hand-tighten the Extractor Blade onto the Cup until sealed; never put a bare blade attachment on the base.
   3. Turn the Cup upside down, set it on the Motor Base and twist clockwise to lock it in place.
   4. Plug in, press POWER, then select a speed or EXTRACT.
   5. Stop blending and wait until the blades are still. Switch off and unplug, then turn the Cup anticlockwise to unlock it before lifting it off; keep it upright before carefully untwisting the blade, pointing the opening away from your body.
   6. For stored drinks, remove the blade and fit a To-Go Lid; do not leave blended food sealed under the blade attachment.
2. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Lid and Vented Lid Cap securely fitted, keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • For cold mixtures, switch to LOW and remove only the lid cap to add ingredients; leave the main Lid fitted. Use only the supplied Tamper, then replace the cap before raising the speed. Do not add through this opening while blending hot ingredients.
3. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
   • Clean the Extractor Blade promptly with a small brush or sponge and soapy water, then dry it completely. Do not remove its components or gasket; replace a loose or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
   • Hand-wash the Tamper with soap and water; scrub stubborn food with a dish brush or sponge.
   • Rinse the Cups and To-Go Lids, brush off debris and place them on the top dishwasher rack without heat/sanitise, or hand-wash them.
   • To loosen dried food, add room-temperature water and 1–2 drops of dish soap. Fill the Cup or Pitcher to its liquid MAX line and fit the blade or Pitcher Lid with its Vented Lid Cap. Blend for 20–30 seconds, stop and unplug, then scrub away the loosened residue and rinse.

   Next steps

   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.
   • Replace the Extractor Blade about every six months, or sooner if its condition or frequency of use requires it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Unpack the Motor Base and attachments onto a flat, dry surface. Rinse the detachable parts and wash them in warm, soapy water. The Pitcher is dishwasher-safe; put Cups and To-Go Lids on the top rack, with no heat/sanitise cycle.
2. Wipe the unplugged Motor Base with a cloth or sponge dampened with warm, soapy water, then dry it. Do not remove the motor base's components.
3. Place the Motor Base on a clean, dry, level counter with clear space beneath and around its ventilation openings. Press the rubber suction feet onto the surface so the base is stable.
4. Put the Pitcher on the counter and add food and sufficient liquid without exceeding its MAX markings. Observe the separate liquid and solid MAX lines. Do not run an empty Pitcher.
5. Fit the Pitcher Lid with the Pour Spout Cover opposite the handle. Align the interlocking mechanism below the thumb-push area with the opening on top of the handle, then push down securely and close the Pour Spout Cover.

Next steps

1. Set the Pitcher on the Motor Base with its handle facing the Control Panel, then twist clockwise until it clicks into place. The motor will only run when the Pitcher and its Lid are properly fitted.
2. Plug in the Motor Base. Press POWER; the blending mode lights illuminate from left to right.
3. Press LOW, MED or HIGH once for continuous blending, or choose SMOOTHIE for the timed cycle. Hold PULSE only for as long as you want the blades to run.
4. Press POWER to stop and wait until the blades stop; the POWER light remains on in idle mode. Press POWER again to switch off, unplug, twist the Pitcher anticlockwise and lift it off. Open the Spout Cover before pouring.
5. Keep each Cup blend to one minute or less. Do not run consecutive one-minute cycles; allow the contents to settle for at least 10–15 minutes before another cycle.

1. Fit and use the single-serve Cup.
   1. For single-serve blending, add cold or room-temperature ingredients and liquid to the Cup, below its MAX line. Keep hot, warm and carbonated ingredients out of the sealed Cup.
   2. Hand-tighten the Extractor Blade onto the Cup until sealed; never put a bare blade attachment on the base.
   3. Turn the Cup upside down, set it on the Motor Base and twist clockwise to lock it in place.
   4. Plug in, press POWER and wait for the controls to illuminate, then press SMOOTHIE.
   5. Stop blending and wait until the blades are still. Switch off and unplug, then turn the Cup anticlockwise to unlock it before lifting it off; keep it upright before carefully untwisting the blade, pointing the opening away from your body.
   6. For stored drinks, remove the blade and fit a To-Go Lid; do not leave blended food sealed under the blade attachment.
2. Add ingredients and avoid a stalled blend.
   • For hot ingredients, use only the vented Pitcher with its Pitcher Lid securely fitted and Pour Spout Cover closed; keep below the fill limits and start at LOW. Increase speed only when the mixture is smooth and steady. Keep hands away from escaping steam and open the Lid carefully after blending.
   • Check that the Pitcher Lid vent openings are clear before blending; do not block the steam outlet.
   • Stay beside the blender while it runs, keep hands away from the blades and remove all utensils before starting; do not put blender parts in a microwave.
   • To add ingredients with the motor stopped, turn the Power Core Blender Combo OFF, wait for the blades to stop, remove the Lid, add food below MAX, and refit the Lid and its interlock before restarting.
3. Clean and store the parts after use.
   • After use, switch off, unplug and wait for all parts to stop; remove the vessel and rinse or brush away food before washing.
   • Use a small brush to clear the Motor Base actuator area while unplugged; wipe any external residue with a damp cloth and dry the surface.
   • Clean the Pitcher and Lid with soap and water, using a brush or sponge for stuck food; keep fingers away from the sharp integrated blade. Rinse before dishwasher cleaning and avoid the sanitise cycle.
   • Check the Pitcher, threads and other food-contact parts for cracking, cloudiness, crazing, warping or breakage. Stop using a damaged part and replace it with a genuine part made for your exact model; do not use a Pitcher that does not fit correctly.
   • Rinse the Cups and To-Go Lids, brush off debris and place them on the top dishwasher rack without heat/sanitise, or hand-wash them.
   • To loosen dried food, add room-temperature water and 1–2 drops of dish soap. Fill the Cup or Pitcher to its liquid MAX line; fit the Extractor Blade to the Cup, or lock the Pitcher Lid onto the Pitcher with its Pour Spout Cover closed. Blend for 20–30 seconds on LOW, stop and unplug, then scrub away the loosened residue and rinse.
   • Store the Pitcher upright with its Lid fitted and nothing on top. Keep the other pieces where they cannot be damaged, and cover all blades rather than leaving them exposed.