1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Prepare for cleaning. These steps cover Ultra 1000 Premium product code NB07500-1008. For another Ultra 1000 product code, follow the cleaning instructions supplied with that exact pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly or pitcher from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
7. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
8. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.

Next steps

9. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade onto the motor base, then gently push and twist to start; turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Switch off and unplug the motor base. Wait until every moving part has stopped, then remove the cup and easy-twist extractor-blade assembly before cleaning.
2. Fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap
3. Attach the easy-twist extractor blade, refit the sealed cup assembly, reconnect power and blend for 20–30 seconds.
4. Stop, unplug and wait for all moving parts to stop before removing the assembly. Scrub away the loosened food with soap and water.
5. Dry the easy-twist extractor blade completely after every use. Check its underside for cracking or breakage and replace a damaged blade immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. These instructions apply to NutriBullet 1000 Series N10-0807DG. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the sealed cup and blade assembly on the motor base and blend for about 20–30 seconds to loosen dried food.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Prepare for cleaning. These steps cover Turbo 1000 product code NBT07400-1006AK. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. These steps cover the black 1000 Series Mega Pack, product code N10-1107AK. For another pack code, match the cleaning method to the guide supplied with it; use the Milling Blade steps only when that blade is included. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and gently turn clockwise to start the automatic cycle; turn the cup anticlockwise to stop after 20–30 seconds.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
7. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
8. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.

Next steps

9. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Unplug the motor base and wait until all moving parts stop. Remove the cup and extractor-blade assembly, then separate them.
2. Fill the cup about two-thirds full with water at 21°C or below and screw the extractor blade on tightly
3. Reconnect power. Place the sealed cup and blade assembly on the motor base, gently push down and twist to start. Blend for about 20–30 seconds.
4. Gently push down and turn the cup anticlockwise to stop. Unplug and wait until all movement stops, then remove and open the assembly normally. Lightly scrub away the loosened food and rinse.
5. Hand-wash the extractor blade with warm soapy water without removing its gasket. Turn the blade on its side in a dish drainer so both sides dry completely.
6. Wipe the unplugged motor base with a warm, soapy damp cloth. NEVER submerge the motor base in water.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.
6. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
7. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.

1. Prepare to clean. These steps cover the cup and blade of Select 1000 product code NB07200-1007DG. For the Select 1000 with pitcher, product code NB07200-1006DG, use its supplied pitcher instructions. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
7. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
8. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.

Next steps

9. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.

1. Unplug the motor base and wait for the blade to stop before removing the cup and blade assembly.
2. Separate the cup from the extractor blade. Fill the cup about two-thirds full with water at 21°C or cooler, then screw the extractor blade on tightly.
3. Reconnect power, invert the sealed cup onto the motor base, then gently push and twist to start. Run for 20–30 seconds; turn the cup anticlockwise to stop.
4. Unplug the base, wait for the blade to stop, then remove the cup assembly. Open the cup, lightly scrub away the loosened food and rinse.
5. Dry the extractor blade completely on its side so both faces dry.
6. With the base unplugged, wipe it with a cloth dampened with warm soapy water. NEVER submerge the motor base in water.

1. Unplug the motor base and wait for the blade to stop before removing the cup and blade assembly.
2. Separate the cup from the extractor blade. Fill the cup about two-thirds full with water at 21°C or cooler, then screw the extractor blade on tightly.
3. Reconnect power, invert the sealed cup onto the motor base, then gently push and twist to start. Run for 20–30 seconds; turn the cup anticlockwise to stop.
4. Unplug the base, wait for the blade to stop, then remove the cup assembly. Open the cup, lightly scrub away the loosened food and rinse.
5. Dry the extractor blade completely on its side so both faces dry.
6. With the base unplugged, wipe it with a cloth dampened with warm soapy water. NEVER submerge the motor base in water.

1. Prepare for cleaning. These steps cover Ultra 1200 McLaren NB07500-1206GO-MC and Club Pack NB07500-1214S. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare Baby for cleaning. Unplug the NutriBullet Baby and wait until every moving part has stopped before removing the cup or Batchbowl and blade.
2. Loosen dried food in a cup. Fill the cup halfway with soapy water and twist on the blade. Place the cup-and-blade assembly onto the Motor Base, reconnect power, then press down and twist clockwise to blend for 10–20 seconds. Twist anticlockwise to stop, unplug and wait for the blade to stop. Remove the assembly and untwist the blade; empty the water, lightly scrub away remaining debris and rinse.
3. Wash the cups and Batchbowl. Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse.
4. Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.

1. Prepare Steam + Blend for cleaning. Turn off and unplug the NutriBullet Baby Steam + Blend, then let it cool completely before handling or cleaning parts.
2. Open and separate the used bowl. Allow at least ten minutes for cooling and wait until the appliance is completely cool and all moving parts have stopped. With the appliance unplugged, turn the Work Bowl clockwise off the base. Open the lid and turn its circular bottom grip anticlockwise to separate the lid into two pieces; remove trapped food or water and dry those pieces fully. Lift the Blending Blade vertically out by a non-sharp area using a mitt.
3. Empty and clean the reservoir and blade stem. Remove food from the Work Bowl, untwist the Water Reservoir Cap and discard remaining water. Use a cloth or soft-bristled brush to clear food from the bowl and inside the lid. Clean inside the Blade Stem to remove food or water, then dry it completely.
4. Rinse food away. Rinse the Work Bowl, Work Bowl Lid and Blending Blade under running water after use, holding the sharp blade by a non-sharp area. Clean the blade after every blend so food and mineral residue cannot build up.
5. Wash the Work Bowl and lid. Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasher.
6. Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.
7. Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use. NEVER submerge the motor base in water.
8. Descale the Water Reservoir. Empty the Water Reservoir. Pour in 240 mL white vinegar. Leave the vinegar for at least 30 minutes, up to 24 hours according to the buildup, then discard it. Rinse with cool water and empty the loosened scale into the sink.

Next steps

9. Finish descaling. After descaling, boil fresh water several times and discard it to remove remaining scale or vinegar. For the final cleaning cycle, let the appliance cool, fill the Water Reservoir to the 25-minute line and lock its cap clockwise. Fit the Blending Blade vertically onto the Blade Holder, lock the Work Bowl Lid clockwise and lock the bowl anticlockwise onto the base. Connect power, select Steam with the Setting Dial and press Power. The indicator flashes blue while steaming; five beeps mark completion. After the cycle, unplug and cool completely; lift the sharp blade vertically out using a mitt, then discard water from the Work Bowl and reservoir. Repeat descaling if limescale remains.
10. Store Steam + Blend. Unplug the appliance when it will not be used for a while. Keep all pieces together and store the assembled NutriBullet Baby Steam + Blend in a safe, dry, cool place.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
8. Take apart the processor for washing. With power disconnected and the blade or disc stopped, turn the Work Bowl Lid anticlockwise and lift it off, then turn the Work Bowl and Processor Base anticlockwise and lift them from the Motor Base.

Next steps

9. Remove the blade or disc. Hold the plastic centre hub of the Chopping Blade or Slice/Shred Disc and pull upwards; never tip the Work Bowl to drop a sharp part into your hand.
10. Remove the Work Bowl from the Processor Base. Hold the Processor Base from below with one hand and the Work Bowl handle with the other, turn the bowl anticlockwise and carefully lift it off the Processor Base and Blade Adapter.
11. Hand-wash the Processor Base and Blade Adapter. Keep the Processor Base and Blade Adapter out of the dishwasher and wash them by hand; alternatively hand-wash all Processor Attachment parts with a sponge or cloth, soap and water.
12. Remove residue from processor blades and discs. Immerse only the removed Blades or Discs in room-temperature water with 1–2 drops of dish soap, wait 20–30 seconds, then carefully scrub away the loosened debris.
13. Take apart the grinder for cleaning. After each use, unplug the Motor Base, wait for the blades to stop, disengage the Coffee & Dry Spice Grinder Attachment and separate the Grinding Cup from the Grinder Blade, handling the sharp blade carefully.
14. Wash the grinder parts. Wash the Grinding Cup and Grinder Blade on the dishwasher top rack only, without the heat or sanitise cycle; alternatively hand-wash them with a sponge or cloth, soap and water.

1. Unplug the motor base and wait for the blade to stop before removing the cup and blade assembly.
2. Separate the cup from the extractor blade. Fill the cup about two-thirds full with water at 21°C or cooler, then screw the extractor blade on tightly.
3. Reconnect power, invert the sealed cup onto the motor base, then gently push and twist to start. Run for 20–30 seconds; turn the cup anticlockwise to stop.
4. Unplug the base, wait for the blade to stop, then remove the cup assembly. Open the cup, lightly scrub away the loosened food and rinse.
5. Dry the extractor blade completely on its side so both faces dry.
6. With the base unplugged, wipe it with a cloth dampened with warm soapy water. NEVER submerge the motor base in water.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
7. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.