1. Use the Frozen Drinks program for ice-blended drinks, or Smoothie for fresh and frozen fruit or vegetables; both are available with the Pitcher and single-serve Cups.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line. Do not overload the vessel or pack it with ice.
4. Fit the Pitcher Lid and Vented Lid Cap, then lock the Pitcher clockwise onto the base. For a Cup, tighten its Extractor Blade before turning the inverted Cup clockwise onto the base.
5. Use only cold or room-temperature liquids in the sealed Cup. Do not add hot, warm, carbonated or effervescent ingredients, including dry ice; frozen food does not remove the pressure risk from unsuitable ingredients.
6. Keep each Cup blend to one minute or less. Do not run consecutive one-minute cycles; allow the contents to settle for at least 10–15 minutes before another cycle.
7. If the thermal breaker stops the motor after overloading, unplug the Motor Base and leave it to cool for one hour before restarting.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. To push food in the Pitcher, use only the supplied Tamper; keep hands and other utensils away from moving blades. If opening the Lid to loosen food, first switch off, unplug and wait until the blade stops, then refit the Lid before restarting.
3. Inspect the vessel and blade assembly after a jam. Stop using and replace a cracked or damaged Pitcher or Cup, or a damaged blade attachment; do not keep blending with a blade that cannot turn freely. Buy a replacement pitcher (Australia) or pitcher (New Zealand). Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
4. If a Cup feels hot or warm, stop and unplug, leave it on the base untouched and do not try to open it. Wait at least 30 minutes and longer if still warm; once completely cool, gently remove it and use a towel to slowly untwist the blade away from your face and body. Never force or pry it open.

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Wash the Pitcher and Cups after use and clear food residue with a brush or sponge; use no heat/sanitise cycle. Wipe the Motor Base.
3. For a stored drink, remove the Extractor Blade and fit a To-Go Lid; never leave a drink sealed under the blade. Store the empty Pitcher upright with its Lid on and protect the other parts.

1. Use EXTRACT for fruit, vegetables and ice in a liquid-based smoothie, or HIGH for frozen fruit and vegetables.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line; on the Pitcher, observe the separate liquid and solid limits. Do not overload the vessel or pack it with ice.
4. Fit the Pitcher Lid and Vented Lid Cap, then lock the Pitcher clockwise onto the base. For a Cup, tighten its Extractor Blade before turning the inverted Cup clockwise onto the base.
5. Use only cold or room-temperature liquids in the sealed Cup. Do not add hot or carbonated ingredients; frozen food does not make a hot or fizzy mixture suitable for a sealed Cup.
6. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.
7. If the motor stops unexpectedly, unplug the base and let it cool for at least 15 minutes before retrying.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. To push food in the Pitcher, use only the supplied Tamper; keep hands and other utensils away from moving blades. If opening the Lid to loosen food, first switch off, unplug and wait until the blade stops, then refit the Lid before restarting.
3. Inspect the vessel and blade assembly after a jam. Stop using and replace a cracked or damaged Pitcher or Cup, or a damaged blade attachment; do not keep blending with a blade that cannot turn freely. Buy a replacement pitcher (Australia) or pitcher (New Zealand). Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
4. If the sealed Cup feels warm, let it cool before carefully opening it away from your body; never remove the blade while blending is still underway.

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Wash the Pitcher and Cups after use and clear food residue with a brush or sponge; use no heat/sanitise cycle. Wipe the Motor Base.
3. For a stored drink, remove the Extractor Blade and fit a To-Go Lid; never leave a drink sealed under the blade. Store the empty Pitcher upright with its Lid on and protect the other parts.

Root vegetables, kale, celery, nuts and seeds may need two AUTO cycles.

1. Select FROZEN DRINKS for ice-blended drinks, SMOOTHIES for fresh or frozen fruit and vegetables, or HIGH for a thick frozen mixture.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line; on the Pitcher, observe the separate liquid and solid limits. Do not overload the vessel or pack it with ice.
4. Fit the Pitcher Lid and Vented Lid Cap, then lock the Pitcher clockwise onto the base. For a Cup, tighten its Extractor Blade before turning the inverted Cup clockwise onto the base.
5. Use only cold or room-temperature liquids in the sealed Cup. Do not add hot or carbonated ingredients; frozen food does not make a hot or fizzy mixture suitable for a sealed Cup.
6. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.
7. If the motor stops unexpectedly, unplug the base and let it cool for at least 15 minutes before retrying.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. To push food in the Pitcher, use only the supplied Tamper; keep hands and other utensils away from moving blades. If opening the Lid to loosen food, first switch off, unplug and wait until the blade stops, then refit the Lid before restarting.
3. Inspect the vessel and blade assembly after a jam. Stop using and replace a cracked or damaged Pitcher or Cup, or a damaged blade attachment; do not keep blending with a blade that cannot turn freely. Buy a replacement pitcher (Australia) or pitcher (New Zealand). Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
4. If the sealed Cup feels warm, let it cool before carefully opening it away from your body; never remove the blade while blending is still underway.

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Wash the Pitcher and Cups after use and clear food residue with a brush or sponge; use no heat/sanitise cycle. Wipe the Motor Base.
3. For a stored drink, remove the Extractor Blade and fit a To-Go Lid; never leave a drink sealed under the blade. Store the empty Pitcher upright with its Lid on and protect the other parts.

1. Use HIGH to blend frozen fruit or vegetables, or SMOOTHIE for a drink; always add sufficient liquid.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line; on the Pitcher, observe the separate liquid and solid limits. Do not overload the vessel or pack it with ice.
4. Secure the Pitcher Lid and cap, align the studs with the base grooves and lower the Pitcher into place until it clicks.
5. Never blend longer than one minute, and do not run consecutive cycles exceeding one minute in total.
6. If overloading trips the thermal breaker, unplug the Motor Base and let it cool for one hour before trying again.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. For stuck food in the Pitcher, use a long spoon or silicone or wooden spatula only after switching off, unplugging and waiting for the blade to stop; do not use sharp or metal tools. Remove the utensil, refit the Lid and cap, then restart.
3. After a jam, inspect the Pitcher and its integrated blade. Stop using the Pitcher and replace it if it is cracked or damaged, or if its blade is damaged or cannot turn freely. Buy a replacement pitcher (Australia) or pitcher (New Zealand).

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Rinse and brush away food from the Pitcher and wash with soap and water or a dishwasher without the sanitise cycle; wipe the Motor Base only.
3. Store the Pitcher upright with the Lid fitted and nothing on top.

1. Use EXTRACT for fruit, vegetables and ice in a liquid-based smoothie, or HIGH for frozen fruit and vegetables.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line; on the Pitcher, observe the separate liquid and solid limits. Do not overload the vessel or pack it with ice.
4. Fit the Pitcher Lid and Vented Lid Cap, then lock the Pitcher clockwise onto the base. For a Cup, tighten its Extractor Blade before turning the inverted Cup clockwise onto the base.
5. Use only cold or room-temperature liquids in the sealed Cup. Do not add hot or carbonated ingredients; frozen food does not make a hot or fizzy mixture suitable for a sealed Cup.
6. Do not run the motor continuously for more than one minute. The Cup speeds stop automatically after 60 seconds; stop a Pitcher run yourself within the one-minute limit.
7. If the motor stops unexpectedly, unplug the base and let it cool for at least 15 minutes before retrying.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. To push food in the Pitcher, use only the supplied Tamper; keep hands and other utensils away from moving blades. If opening the Lid to loosen food, first switch off, unplug and wait until the blade stops, then refit the Lid before restarting.
3. Inspect the vessel and blade assembly after a jam. Stop using and replace a cracked or damaged Pitcher or Cup, or a damaged blade attachment; do not keep blending with a blade that cannot turn freely. Buy a replacement pitcher (Australia) or pitcher (New Zealand). Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
4. If the sealed Cup feels warm, let it cool before carefully opening it away from your body; never remove the blade while blending is still underway.

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Wash the Pitcher and Cups after use and clear food residue with a brush or sponge; use no heat/sanitise cycle. Wipe the Motor Base.
3. For a stored drink, remove the Extractor Blade and fit a To-Go Lid; never leave a drink sealed under the blade. Store the empty Pitcher upright with its Lid on and protect the other parts.

1. Use HIGH to blend frozen fruit or vegetables, or SMOOTHIE for a drink; always add sufficient liquid.
2. Do not use the blender as an ice crusher or run ice alone; this can jam the blades or damage the vessel. Keep ice and frozen ingredients moving in sufficient liquid.
3. Add all ingredients below the vessel MAX line; on the Pitcher, observe the separate liquid and solid limits. Do not overload the vessel or pack it with ice.
4. Fit the Pitcher Lid with the Pour Spout Cover closed, then lock the Pitcher clockwise onto the base. For a Cup, tighten its Extractor Blade before turning the inverted Cup clockwise onto the base.
5. Use only cold or room-temperature liquids in the sealed Cup. Do not add hot, warm, carbonated or effervescent ingredients, including dry ice; frozen food does not remove the pressure risk from unsuitable ingredients.
6. Keep each Cup blend to one minute or less. Do not run consecutive one-minute cycles; allow the contents to settle for at least 10–15 minutes before another cycle.
7. If the thermal breaker stops the motor after overloading, unplug the Motor Base and leave it to cool for one hour before restarting.

1. If the blade stops or the mixture will not circulate, stop blending, unplug and wait until all movement has stopped. Remove some of an overloaded mixture and add more liquid before refitting the vessel and trying again.
2. To loosen food in the Power Core Blender Combo Pitcher, switch off, unplug and wait for the blade to stop before opening the Lid. Use a utensil only while stopped, remove it, and refit the Lid before restarting.
3. Inspect the vessel and blade assembly after a jam. Stop using and replace a cracked or damaged Pitcher or Cup, or a damaged blade attachment; do not keep blending with a blade that cannot turn freely.
4. If a Cup feels hot or warm, stop and unplug, leave it on the base untouched and do not try to open it. Wait at least 30 minutes and longer if still warm; once completely cool, gently remove it and use a towel to slowly untwist the blade away from your face and body. Never force or pry it open.

1. Stop the blend and wait for the blades to stop before switching off, unplugging and removing the vessel.
2. Wash the Pitcher and Cups after use and clear food residue with a brush or sponge; use no heat/sanitise cycle. Wipe the Motor Base.
3. For a stored drink, remove the Extractor Blade and fit a To-Go Lid; never leave a drink sealed under the blade. Store the empty Pitcher upright with its Lid on and protect the other parts.