Replace the complete blade attachment where its seal is fixed and loose or missing; for other Magic Bullet seals, have the affected part identified for the correct replacement.
If you are unsure which model you own, use Find my model before choosing replacement parts.
Need help identifying a replacement?
Have the full model name or product code and a clear photo of the affected part ready for our team. Keep the part out of use until the correct replacement or refitting instructions are identified.
Has liquid entered the motor base or electrical body?
If liquid has entered the motor base or electrical body, stop using it, unplug it only if it is safe to do so, and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).
If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.
Magic Bullet To Go 200W
Replace the complete Magic Bullet To Go 200W Cross Blade if its gasket is loose, missing or damaged; the factory-sealed gasket cannot be replaced separately. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
Is the Cross Blade gasket loose, worn or split?
- Unplug the Magic Bullet To Go 200W and wait for every moving part to stop. Remove the Cup and Cross Blade from the Motor Base, turn the Cup upright and unscrew the Cross Blade.
- Inspect the rubber gasket in the Cross Blade without pulling it out. It should be undamaged and completely seated in the blade assembly.
- If the gasket is worn, torn or loose, stop using the Cross Blade and replace the whole blade attachment. A gasket that keeps coming out after only a few uses still needs this replacement action. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
- The sealed gasket keeps food particles on its surface and helps with cleaning.
- Replace the Cross Blade about every six months, or as needed.
Has the gasket been removed or gone missing?
- Keep the Magic Bullet To Go 200W Cross Blade out of use if the seal has been removed or is missing.
- Do not try to push a replacement ring into the blade housing. The gasket is factory-sealed and is not designed to be removed or replaced separately.
- Order the correct complete Cross Blade for the Magic Bullet To Go 200W. Keep the old blade aside until the replacement is available.
Was the Cross Blade washed in the dishwasher?
- Check how the Magic Bullet To Go 200W blade attachment was cleaned. The guide warns that dishwasher hot-water exposure can damage its outer-rim seal.
- Inspect the gasket without disturbing it; if loose or damaged, replace the whole Cross Blade. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
- For a sound blade, hand-clean it as instructed in the guide and keep it out of the dishwasher. Never pull the gasket out to clean underneath it.
Is a clean, intact Cross Blade loosely screwed onto the Cup?
- Check the Magic Bullet To Go 200W Cup and Cross Blade for damage before assembly. Clean the separate components and inspect the seated gasket again.
- Twist the Cross Blade onto the Cup until firmly sealed and hand-tightened, with the blade attachment aligned properly.
- If the connection cannot tighten, or the Cup is cracked or damaged, stop using that component and replace it. A loose blade-to-Cup connection should not be corrected by removing the blade gasket.
Magic Bullet Blender Combo
Arrange a complete Magic Bullet Blender Combo Cross Blade replacement if its seal is loose, missing or damaged; the seal cannot be replaced separately.
Is the Cross Blade gasket missing, damaged or displaced?
- Turn the Magic Bullet Blender Combo off, unplug it and wait until the blades have stopped. If the sealed Cup feels hot or warm, leave it on the Motor Base without touching or opening it for at least 30 minutes; allow more time if it is still warm.
- Only when the Cup is completely cool, slowly disengage it from the Motor Base. Point the Cup away from your face and body, cover the Cross Blade with a towel and slowly untwist it to release residual pressure. Do not force or pry apart a stuck assembly; chat with us for help.
- Check the Cross Blade gasket without pulling it out. A displaced or damaged seal can cause leakage; a missing or damaged gasket means the Cross Blade must be taken out of use.
- The blade seal is non-removable and cannot be replaced separately. Chat with us to arrange the correct blade-assembly replacement before using the affected attachment again.
Is the Cross Blade not tightened securely to the vessel?
- For an intact Magic Bullet Blender Combo Cross Blade, check that the Cup or Blending Pitcher is undamaged and clean.
- Securely tighten the Cross Blade onto the Cup or Blending Pitcher before fitting the vessel to the Motor Base.
- If a leak starts during blending, turn the power off and wait for the motor to stop. For a hot or warm sealed Cup, follow the cooling and opening steps above before removal; inspect the seal and replace a damaged attachment before reuse.
Has cleaning or heat damaged the blade seal?
- Hand-clean the Magic Bullet Blender Combo blade attachment under lukewarm water and keep its seal in place.
- Do not expose the attachment to boiling water, a microwave, an oven or the dishwasher heat/sanitise cycle. Those conditions can damage components.
- Inspect the clean gasket before reassembly. If it is loose, damaged or missing, stop using the Cross Blade and arrange replacement; cleaning will not restore a damaged seal.
Magic Bullet Mini Juicer
Request the correct Magic Bullet Mini Juicer replacement part if a seal or piece has come away from the Juice Cup Lid or the lid will not close securely.
Is the Juice Cup Lid not sealing or closing?
- Remove the Magic Bullet Mini Juicer Juice Cup Lid and empty the Cup. Wash the detached Cup and lid in warm, soapy water and rinse.
- Refit the Juice Cup Lid tightly and close the latch for storage. Keep the Cup upright and leave the top of the lid clear.
- If the lid will not close or a piece has come away, stop using the lid for sealed storage and request the correct replacement part.
Is the lid or another detachable part damaged?
- Switch the Magic Bullet Mini Juicer off, unplug it and wait for all moving parts to stop before inspecting the detached component.
- Identify where the loose piece came from and check the surrounding part for damage. Do not operate with a damaged component; replace the affected part.
- Ask for replacement advice using the Magic Bullet Mini Juicer model and part details. Keep the loose piece available to identify the correct assembly.
Magic Bullet Kitchen Express 250W
Do not use the affected Magic Bullet Kitchen Express 250W part again until a loose or missing seal is replaced with the correct component. Chat with us and ask our team to identify it.
Has a seal or part come away from the Cross Blade or work bowl?
- Turn the Magic Bullet Kitchen Express 250W control knob to OFF, unplug the Motor Base and wait for the blade or disc to stop.
- Remove the affected vessel from the Motor Base and identify whether the loose piece came from the Cup and Cross Blade or from the work bowl and lid.
- Do not use any part that appears damaged. Have the affected component identified for replacement before using it again; keep the loose piece with it for checking.
Is the Cup and Cross Blade connection not tight?
- With the Magic Bullet Kitchen Express 250W disconnected, check the intact Cup and Cross Blade for food residue and clean the separate parts.
- Twist the Cross Blade assembly onto the Cup until the two are tightly sealed. Turn the assembly upside down and twist clockwise onto the Motor Base to lock it.
- If the blade assembly will not tighten correctly, leave it out of use and replace the affected component instead of blending with an insecure connection.
Could cleaning heat have warped the vessel or lid?
- Inspect the Magic Bullet Kitchen Express 250W Cup, work bowl and lid for damage after washing.
- Clean removable parts on the dishwasher top rack or hand-wash with warm, soapy water and rinse. Never use the sanitise cycle; it can warp the Cup or work bowl.
- Do not force a warped component into position. Stop using the damaged part and obtain the correct replacement.
Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: Magic Bullet To Go 200W user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Blender Combo user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Mini Juicer user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Kitchen Express 250W user guide (PDF)