1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning. These steps cover Ultra 1000 Premium product code NB07500-1008. For another Ultra 1000 product code, follow the cleaning instructions supplied with that exact pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly or pitcher from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.

Next steps

1. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
2. Wash the pitcher. Rinse and briefly brush the pitcher before putting it in the dishwasher, without the sanitise cycle; alternatively hand-wash it with soap and water and remove stuck food with a dish brush or sponge.
3. Clean the tamper. Always hand-wash the tamper with soap and water; scrub stuck-on ingredients with a dish brush or sponge.
4. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
5. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
6. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade onto the motor base, then gently push and twist to start; turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Switch off and unplug the motor base Wait until every moving part has stopped, then remove the cup and easy-twist extractor-blade assembly before cleaning.
2. Wash the cups and to-go lids on the dishwasher top rack, without a sanitise cycle
3. Hand-wash the easy-twist extractor blade with soap and water Do not remove any blade components.
4. Wipe the unplugged motor base with a cloth dampened with warm soapy water Use a small brush on the actuator area if needed. NEVER submerge the motor base in water.
5. Dry the easy-twist extractor blade completely after every use. Check its underside for cracking or breakage and replace a damaged blade immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. These instructions apply to NutriBullet 1000 Series N10-0807DG. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the sealed cup and blade assembly on the motor base and blend for about 20–30 seconds to loosen dried food.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning. These steps cover Turbo 1000 product code NBT07400-1006AK. For NBT07400-1004AW or NBT07400-1006AW, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. These steps cover the black 1000 Series Mega Pack, product code N10-1107AK. For another pack code, match the cleaning method to the guide supplied with it; use the Milling Blade steps only when that blade is included. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 12 Piece pack, product code N12-1207C, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 10 Piece pack, product code N12-1007, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and gently turn clockwise to start the automatic cycle; turn the cup anticlockwise to stop after 20–30 seconds.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.

Next steps

1. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.
2. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
3. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
4. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
5. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning.

   Unplug the motor base and wait for all moving parts to stop before removing or separating the cup and blade. Let a warm sealed cup cool before carefully opening it away from your body.

2. Wash the cup and lid.

   Cups and To-Go Lids can be washed by hand in warm soapy water or placed on the dishwasher’s top rack. Do not use the sanitise cycle; it can warp the plastic.

3. Hand-wash the extractor blade.

   Hand-wash the extractor blade with warm soapy water and rinse. Keep it out of the dishwasher, leave its gasket in place, and dry both sides completely. A loose or damaged gasket requires a complete replacement extractor blade.

4. Wipe the motor base.

   Wipe the unplugged base with a sponge or cloth dampened with warm soapy water. Use a small brush if needed on accessible white actuator tabs. NEVER submerge the motor base in water. Do not remove the motor base's rubber or plastic liners. If liquid has entered the electrical base, leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Run the cleaning blend. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse before dishwashing. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare to clean. These steps cover the cup and blade of Select 1000 product code NB07200-1007DG. For the Select 1000 with pitcher, product code NB07200-1006DG, use its supplied pitcher instructions. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Remove the cup and blade. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill and seal the cup. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Run the cleaning blend. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.

Next steps

1. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.
2. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
3. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
4. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
5. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Find the full product code on the appliance label. NEVER submerge the motor base in water.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Find the full product code on the appliance label. NEVER submerge the motor base in water.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Prepare for cleaning. These steps cover Ultra 1200 McLaren product code NB07500-1206GO-MC. For Club Pack product code NB07500-1214S, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare Baby for cleaning. Unplug the NutriBullet Baby and wait until every moving part has stopped before removing the cup or Batchbowl and blade.
2. Loosen dried food in a cup. Fill the cup halfway with soapy water and twist on the blade. Place the cup-and-blade assembly onto the Motor Base, reconnect power, then press down and twist clockwise to blend for 10–20 seconds. Twist anticlockwise to stop, unplug and wait for the blade to stop. Remove the assembly and untwist the blade; empty the water, lightly scrub away remaining debris and rinse.
3. Wash the cups and Batchbowl. Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse.
4. Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.

1. Prepare Steam + Blend for cleaning. Turn off and unplug the NutriBullet Baby Steam + Blend, then let it cool completely before handling or cleaning parts.
2. Open and separate the used bowl. Allow at least ten minutes for cooling and wait until the appliance is completely cool and all moving parts have stopped. With the appliance unplugged, turn the Work Bowl clockwise off the base. Open the lid and turn its circular bottom grip anticlockwise to separate the lid into two pieces; remove trapped food or water and dry those pieces fully. Lift the Blending Blade vertically out by a non-sharp area using a mitt.
3. Empty and clean the reservoir and blade stem. Remove food from the Work Bowl, untwist the Water Reservoir Cap and discard remaining water. Use a cloth or soft-bristled brush to clear food from the bowl and inside the lid. Clean inside the Blade Stem to remove food or water, then dry it completely.
4. Rinse food away. Rinse the Work Bowl, Work Bowl Lid and Blending Blade under running water after use, holding the sharp blade by a non-sharp area. Clean the blade after every blend so food and mineral residue cannot build up.
5. Wash the Work Bowl and lid. Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasher.

Next steps

1. Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.
2. Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use. NEVER submerge the motor base in water.
3. Descale the Water Reservoir. Empty the Water Reservoir. Use a suitable chemical-free descaler or pour in 240 mL white vinegar. Leave the vinegar for at least 30 minutes, up to 24 hours according to the buildup, then discard it. Rinse with cool water and empty the loosened scale into the sink.
4. Finish descaling. After descaling, boil fresh water several times and discard it to remove remaining scale or vinegar. For the final cleaning cycle, let the appliance cool, fill the Water Reservoir to the 25-minute line and lock its cap clockwise. Fit the Blending Blade vertically onto the Blade Holder, lock the Work Bowl Lid clockwise and lock the bowl anticlockwise onto the base. Connect power, select Steam with the Setting Dial and press Power. The indicator flashes blue while steaming; five beeps mark completion. After the cycle, unplug and cool completely; lift the sharp blade vertically out using a mitt, then discard water from the Work Bowl and reservoir. Repeat descaling if limescale remains.
5. Store Steam + Blend. Unplug the appliance when it will not be used for a while. Keep all pieces together and store the assembled NutriBullet Baby Steam + Blend in a safe, dry, cool place.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.

Next steps

1. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
2. Take apart the processor for washing. With power disconnected and the blade or disc stopped, turn the Work Bowl Lid anticlockwise and lift it off, then turn the Work Bowl and Processor Base anticlockwise and lift them from the Motor Base.
3. Remove the blade or disc. Hold the plastic centre hub of the Chopping Blade or Slice/Shred Disc and pull upwards; never tip the Work Bowl to drop a sharp part into your hand.
4. Remove the Work Bowl from the Processor Base. Hold the Processor Base from below with one hand and the Work Bowl handle with the other, turn the bowl anticlockwise and carefully lift it off the Processor Base and Blade Adapter.
5. Remove residue from processor blades and discs. Immerse only the removed Blades or Discs in room-temperature water with 1–2 drops of dish soap, wait 20–30 seconds, then carefully scrub away the loosened debris.
6. Wash the processor parts. Put the Blades, Discs, Work Bowl and Work Bowl Lid on the dishwasher top rack only; never use the heat or sanitise cycle.

Next steps

1. Hand-wash the Processor Base and Blade Adapter. Keep the Processor Base and Blade Adapter out of the dishwasher and wash them by hand; alternatively hand-wash all Processor Attachment parts with a sponge or cloth, soap and water.
2. Take apart the grinder for cleaning. After each use, unplug the Motor Base, wait for the blades to stop, disengage the Coffee & Dry Spice Grinder Attachment and separate the Grinding Cup from the Grinder Blade, handling the sharp blade carefully.
3. Wash the grinder parts. Wash the Grinding Cup and Grinder Blade on the dishwasher top rack only, without the heat or sanitise cycle; alternatively hand-wash them with a sponge or cloth, soap and water.
4. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
5. Store the processor blade and disc safely. Fit the Blade Adapter onto the Work Bowl centre shaft, followed by the Chopping Blade; hold the Disc by its centre knob and lower it to the lower storage position about halfway down the adapter shaft without aligning their marks, then attach the Work Bowl Lid.

1. Find the full product code on the appliance label. NEVER submerge the motor base in water.
2. Check the user guide supplied with that product code for the care instructions while you wait for help.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Remove the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill and seal the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the cleaning blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.