1. Turn the blender off after use and unplug the charging cable before cleaning; wait until the blades have completely stopped.
2. Hand-wash the Cup and Lid with warm, soapy water and rinse, or use the dishwasher top rack without a heat or sanitise cycle.
3. Gently rinse only the blade assembly and wipe it with a damp sponge or cloth, keeping fingers away from the sharp edges. Do not run the base under water or put the motor base in the dishwasher.
4. Replace a Cup with cracks, cloudiness or other damage, and stop using a bent or damaged blade.
5. Keep the blender away from extreme heat or cold, open flames and direct sunlight; these conditions can damage seals, batteries and other parts.
6. Wipe a wet exterior gently with a clean, dry cloth; do not use a hair dryer, clothes dryer, microwave or oven to dry it.
7. Store the blender upright with the Cup attached to cover its blades, somewhere safe with nothing stacked on top.

1. Unplug the charging cable and leave the blender undisturbed for 90 seconds so it shuts down; wait for the blades to stop before cleaning or taking it apart.
2. For a cleaning cycle, rinse the Blending Cup, half-fill it with cold water and add a drop of dish soap. For stubborn residue, let the soapy water sit on each end of the Cup for a few minutes.
3. Secure the Cup, run a blending cycle, and flip and shake the blender to agitate the water; when the cycle finishes, open the Flip-Top Lid and empty it.
4. Repeat the cleaning cycle with fresh water and no soap for the final rinse, then dry the Motor Base, Blade and Lid upright with the Flip-Top Lid open.
5. To wash the blade area by hand, point it down at an angle and rinse only that area while keeping a thumb or finger over the USB-C port. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the whole Motor Base, Blade and Lid.

Next steps

1. To clean the Drinking Spout, face the blade up, keep the USB-C port covered, and gently rinse the sip hole with warm water. Use the supplied Cleaning Brush on the straw, under the blades, sip hole and vent hole.
2. Wipe and dry the Motor Base, Blade and Lid and the USB-C port with a clean cloth; let the port dry completely before charging.
3. Wash the Blending Cup and To-Go Lid with soap and water or on the dishwasher top rack without heat or sanitise cycles; keep the Motor Base, Blade and Lid out of the dishwasher.
4. Store in a dry, temperature-controlled place with the Cup or Blade Cover attached to cover the blades and nothing stacked on top; avoid tightly winding, sharply bending or creasing the charging cable.

The table below gives the Blending Cup and blade materials for the listed product codes and countries.

Match the complete code on your blender. These material details apply only to the named part and listed codes.

1. Turn the blender off after each use and wait until the blades stop before removing parts.
2. Twist the Blade Block clockwise to remove it, keeping fingers away from its edges; unscrew the Sip Lid with Carry Loop counterclockwise.
3. Hand-wash the Blade Block, Blending Cup and Sip Lid with Carry Loop in warm, soapy water and rinse. The Blending Cup and Sip Lid may also go on the dishwasher top rack without the sanitise cycle.
4. If the lid gasket moves during washing or drying, remove moisture from its seating area and gently guide the gasket back into place.
5. Wipe food off the Motor Base with a damp cloth. Keep the Motor Base out of the dishwasher. NEVER submerge the motor base in water. Do not hold the motor base under running water.

Next steps

1. Keep the Silicone Charge Port Cover over the charging port to protect it from liquid; check that the port and blender are dry before charging.
2. Replace a Blending Cup with cracks, cloudiness or damage; stop using a bent or damaged Blade Block.
3. Keep the blender away from extreme temperatures, direct sunlight and heat sources, and do not dry it with a hair dryer, clothes dryer, microwave or oven.
4. Store the blender upright with the Blade Block secured to the Blending Cup and the Sip Lid attached, with nothing stacked on top and out of reach of small children.

The supplied cups for NB07300, NB07300B, NB07300MA, NB07300L, NB07300S, NB07300TQ and NB07300W are BPA-free. The supplied cup for GO Black NB07300 is Tritan plastic.

The separately sold GO replacement cup BDM-VE032CDB is BPA-free plastic. These statements describe the cups only.

1. Turn the blender off and check that no light is on and the motor and blades have stopped before removing the Cup.
2. Wash the Cup and Lid on the dishwasher top rack, or hand-wash with warm, soapy water and rinse.
3. Gently rinse only the blade assembly and clean carefully with a damp sponge or cloth without touching the sharp edges; the blade assembly is not dishwasher-safe.
4. NEVER submerge the motor base in water. Do not hold the base directly under running water.
5. Keep hot liquids, ice and frozen ingredients out of the blending vessel; remove fruit and vegetable rinds, peels and stone-fruit pits before blending.
6. Store all parts together in a safe place where they cannot be damaged or cause harm.