Skip to main content

How can we help?

How do I clean a spill in the base of my NutriBullet?

  • Updated

Switch off and disconnect power before wiping accessible base spills with a damp cloth. Let hot appliances cool completely; wash detached washable parts separately.

Is liquid getting into, or coming from inside, the base?

If liquid has entered the motor base or electrical housing, or dark or oily-looking liquid is coming from inside it, stop using it, unplug it only if it is safe to do so, and see our warranty article. Keep a rechargeable appliance disconnected from its charger; do not open the housing or run another cycle to test it.

If a leak continues after the checks, or the source is unclear, leave the appliance off and use the same help link. Include the full model name and where the liquid appeared.

If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.

NutriBullet Ultra 1200

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Ultra 1200 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Ultra 1200, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Ultra 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Ultra 1200 Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Ultra 1200 cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet 900 Series

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 900 Series Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 900 Series, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 900 Series Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 900 Series extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 900 Series cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 900 Essentials Set (AU and NZ)

Unplug the appliance and wait for all movement to stop before cleaning. Hand-clean spills from the NutriBullet 900 Essentials Set NB9-0807DG Motor Base with a cloth dampened with warm soapy water. No dishwasher-cleaning method for the electrical base is provided here.

  1. Unplug the motor base and wait until every moving part has stopped before handling or cleaning it.
  2. Wipe the accessible motor base with a cloth dampened with warm soapy water. NEVER submerge the motor base in water.
  3. Use a small brush if needed to clean sticky debris around the white actuator tabs inside the unplugged base.
What if the cup still will not engage?
  1. Check all three tabs on the cup. Stop using the cup and replace it if a tab is broken, damaged or missing.

If the blender malfunctions, has been dropped or is damaged, stop using it.

NutriBullet 900 Mega Pack Black (AU and NZ)

Unplug the appliance and wait for all movement to stop before cleaning. Hand-clean spills from the NutriBullet 900 Mega Pack Black NB9-1107AK Motor Base with a cloth dampened with warm soapy water. No dishwasher-cleaning method for the electrical base is provided here.

  1. Unplug the motor base and wait until every moving part has stopped before handling or cleaning it.
  2. Wipe the accessible motor base with a cloth dampened with warm soapy water. NEVER submerge the motor base in water.
  3. Use a small brush if needed to clean sticky debris around the white actuator tabs inside the unplugged base.
What if the cup still will not engage?
  1. Check all three tabs on the cup. Stop using the cup and replace it if a tab is broken, damaged or missing.

If the blender malfunctions, has been dropped or is damaged, stop using it.

NutriBullet 600 Series

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 600 Series Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 600 Series, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 600 Series Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 600 Series extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 600 Series cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Ultra 1000 / Ultra 1000 Premium

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Ultra 1000 / Ultra 1000 Premium Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Ultra 1000 / Ultra 1000 Premium, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Ultra 1000 / Ultra 1000 Premium Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Ultra 1000 / Ultra 1000 Premium Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Ultra 1000 / Ultra 1000 Premium cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet Select 1200 / 2.0 Select 1200

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Select 1200 / 2.0 Select 1200 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Select 1200 / 2.0 Select 1200, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Select 1200 / 2.0 Select 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Select 1200 / 2.0 Select 1200 cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Pro+ 1200 / Pro Plus 1200

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Pro+ 1200 / Pro Plus 1200 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Pro+ 1200 / Pro Plus 1200, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Pro+ 1200 / Pro Plus 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Pro+ 1200 / Pro Plus 1200 extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Pro+ 1200 / Pro Plus 1200 cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 2.0 Pro 1000 โ€” New Zealand

Unplug the appliance and wait for all movement to stop before cleaning. Wipe surface spills from the NutriBullet 2.0 Pro 1000 NB07100-1008DG Motor Base in New Zealand with a cloth or sponge dampened with warm soapy water. Leave its housing intact.

  1. Switch off and unplug the NutriBullet 2.0 Pro 1000 NB07100-1008DG, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 2.0 Pro 1000 NB07100-1008DG Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 2.0 Pro 1000 NB07100-1008DG easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup?
  • For dried food in the NutriBullet 2.0 Pro 1000 NB07100-1008DG cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 1000 Series

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 1000 Series Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 1000 Series, then wait until every moving part has stopped.
  2. Remove the cup and Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 1000 Series Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 1000 Series Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 1000 Series cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Turbo 1000

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Turbo 1000 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Turbo 1000, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Turbo 1000 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Turbo 1000 Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Turbo 1000 cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet 1000 Mega Pack / 1000 Series Mega Pack

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack Motor Base (N10-1107AK) with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. For product code N10-1107AK. Switch off and unplug the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack, then wait until every moving part has stopped.
  2. Remove the cup and Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 1000 Mega Pack / 1000 Series Mega Pack Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 1000 Mega Pack / 1000 Series Mega Pack Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 1200 Series / 12 Piece

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 1200 Series / 12 Piece Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 1200 Series / 12 Piece, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 1200 Series / 12 Piece Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 1200 Series / 12 Piece extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 1200 Series / 12 Piece cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 1200 Series / 10 Piece

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 1200 Series / 10 Piece Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 1200 Series / 10 Piece, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 1200 Series / 10 Piece Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 1200 Series / 10 Piece extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 1200 Series / 10 Piece cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 2.0 Pro 1200

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 2.0 Pro 1200 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 2.0 Pro 1200, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 2.0 Pro 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 2.0 Pro 1200 easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 2.0 Pro 1200 cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 500 Series / 4 Piece

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 500 Series / 4 Piece Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 500 Series / 4 Piece, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 500 Series / 4 Piece Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 500 Series / 4 Piece extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 500 Series / 4 Piece cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet 1000 Essentials McLaren

Leave the NutriBullet 1000 Essentials McLaren off and see our warranty article for the cleaning steps before taking it apart.

  1. Have product code N10-0807GO-MC ready when asking for help, along with the model information printed on the appliance label. Do not open the housing.
  2. Do not run a cleaning blend or restart the appliance to test it. NEVER submerge the motor base in water.

NutriBullet 700 Series

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 700 Series Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 700 Series, then wait until every moving part has stopped.
  2. Remove the cup and Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 700 Series Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 700 Series Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 700 Series cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Select 1000 / Select 1000 with pitcher

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Select 1000 / Select 1000 with pitcher Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Select 1000 / Select 1000 with pitcher, then wait until every moving part has stopped.
  2. Remove the cool NutriBullet Select 1000 / Select 1000 with pitcher cup and easy-twist extractor blade together, turn the cup upright and unscrew the blade.
  3. Wipe the accessible NutriBullet Select 1000 / Select 1000 with pitcher Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Select 1000 / Select 1000 with pitcher easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup?
  • For dried food in the NutriBullet Select 1000 / Select 1000 with pitcher cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Pro+ Matte Black

Leave the NutriBullet Pro+ Matte Black off and see our warranty article for the cleaning and drying steps before taking it apart.

  1. Have product code N12-1207MK-C ready when asking for help, along with the model information printed on the appliance label. Do not open the housing.
  2. See our warranty article and explain whether food is on an accessible surface or liquid has entered the base. Do not run another blend to test it. NEVER submerge the motor base in water.

NutriBullet 600 Essentials Kit

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 600 Essentials Kit Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 600 Essentials Kit, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 600 Essentials Kit Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 600 Essentials Kit extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 600 Essentials Kit cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Ultra 1200 McLaren / Club Pack

Unplug the appliance and wait for all movement to stop before cleaning.

  1. Switch off and unplug the NutriBullet Ultra 1200 McLaren / Club Pack, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Ultra 1200 McLaren / Club Pack Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Ultra 1200 McLaren / Club Pack Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Ultra 1200 McLaren / Club Pack cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet Ultra 1200 Premium

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Ultra 1200 Premium Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Ultra 1200 Premium, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Ultra 1200 Premium Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Ultra 1200 Premium Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again. Buy a replacement extractor blade in New Zealand.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Ultra 1200 Premium cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet Triple Prep System

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Triple Prep System Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Triple Prep System, then wait until every moving part has stopped.
  2. Detach the cool Cup and Extractor Blade together or unlock and remove the Pitcher. For the Work Bowl, unlock its Lid counter-clockwise first, then twist the Work Bowl counter-clockwise off the base; carefully lift out the blade or disc by its plastic centre before emptying the food.
  3. Wipe the accessible NutriBullet Triple Prep System Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the Cup, Extractor Blade, Pitcher and Lid, or Work Bowl and Lid, separately with soap and water. Remove the Work Bowl Blade Attachments or Discs and Blade Adapter for cleaning, keep fingers away from cutting edges, then rinse and dry the washable parts.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Triple Prep System Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Triple Prep System cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Blender Combo 1200

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Blender Combo 1200 Motor Base (NBF07500-1210DG) with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. For product code NBF07500-1210DG. Switch off and unplug the NutriBullet Blender Combo 1200, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Blender Combo 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Blender Combo 1200 easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Blender Combo 1200 cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet SmartSense Blender โ€” Australia

Unplug the appliance and wait for all movement to stop before cleaning. Wipe spills from the NutriBullet SmartSense Blender NBF07600 Motor Base with a damp cloth; the Motor Base and Tamper must stay out of the dishwasher, while the Pitcher is dishwasher-safe.

  1. Wipe accessible splashes from the NutriBullet SmartSense Blender Motor Base with a damp cloth. NEVER submerge the motor base in water.
  2. Hand-wash the Tamper with soap and water. The Pitcher is dishwasher-safe; the Tamper and Motor Base must stay out of the dishwasher.

NutriBullet Smart Touch Blender Combo

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Smart Touch Blender Combo Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Smart Touch Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Smart Touch Blender Combo Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Smart Touch Blender Combo easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Smart Touch Blender Combo cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Power Core Blender

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Power Core Blender Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Power Core Blender, then wait until every moving part has stopped.
  2. Unlock and remove the Pitcher from the Motor Base, take off the Lid and empty the remaining ingredients.
  3. Wipe the accessible NutriBullet Power Core Blender Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Power Core Blender Pitcher from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned Pitcher is sound before refitting it. Replace damaged detachable parts before further use. Buy a replacement pitcher in Australia or New Zealand.

NutriBullet Blender Combo 1000

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Blender Combo 1000 Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Blender Combo 1000, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Blender Combo 1000 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Blender Combo 1000 easy-twist extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Blender Combo 1000 cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Power Core Blender Combo

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Power Core Blender Combo Motor Base (NBF07202AK) with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. For product code NBF07202AK. Switch off and unplug the NutriBullet Power Core Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and Extractor Blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Power Core Blender Combo Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet Power Core Blender Combo cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.
Is food left on the detached Extractor Blade?
  • With the NutriBullet Power Core Blender Combo off and unplugged, remove the Cup and unscrew its Extractor Blade after the contents are cool.
  • Hand-wash the detached blade with warm soapy water, keeping fingers away from the sharp edges. Rinse away residue and dry the washable parts before reassembly.
  • Inspect the gasket and blade condition before refitting. Replace a damaged blade assembly instead of reusing it.

NutriBullet Power Core Plus

Keep the NutriBullet Power Core Plus switched off and do not open the housing.

  1. Leave the NutriBullet Power Core Plus switched off while the source of the liquid is unresolved. NEVER submerge the motor base in water.
  2. Read the model code on the appliance label and include it with a description of where the liquid appears when you see our warranty article. Do not remove seals or open the housing to investigate.

NutriBullet Portable Blender / Portable Blender McLaren

Turn the blender off, disconnect its charging cable and wait for the blades to stop. Wipe the outside of the NutriBullet Portable Blender / Portable Blender McLaren Motor Base with a damp cloth and dry it with a clean cloth. Do not hold the motor base under running water.

  1. Turn the NutriBullet Portable Blender / Portable Blender McLaren off, disconnect its charging cable, and wait for the blades to stop before removing the Cup or Lid.
  2. Empty a cool cup, then remove the Cup and Lid for washing. If the contents are warm or pressurised, leave the cup alone until it has cooled for at least 30 minutes, longer if needed, before slowly opening the Lid away from your face and body.
  3. Hand-wash the Cup and Lid in warm soapy water and rinse them clean.
  4. Gently rinse only the blade assembly and wipe away food with a damp sponge or cloth, keeping fingers clear of its sharp edges. NEVER submerge the motor base in water. Do not run the motor base under water; wipe its exterior with a damp cloth instead.
  5. Dry the exterior with a clean cloth and allow all wet parts to dry thoroughly. Keep the charging connection dry before use or charging.
  6. Reattach the Cup with its alignment dots lined up with the Motor Base, fit the Lid and lock the Lid Latch upright. Store the blender upright with the Cup attached so the blades are covered.
Is food still stuck around the blade assembly?
  • With the NutriBullet Portable Blender / Portable Blender McLaren off and disconnected, use a damp sponge or cloth to clean accessible residue around the blade without touching its cutting edges.
  • The guide allows a gentle rinse of the blade assembly only. Keep the Motor Base out of the water stream.
  • If residue cannot be reached without opening the motor housing or detaching the blade, leave those parts assembled and keep the blender out of use until support can advise.
Did cleaning reveal a damaged cup or blade?
  • Check the clean NutriBullet Portable Blender / Portable Blender McLaren Cup for cracking or cloudiness and inspect the blade for bending or other damage.
  • Replace a damaged detachable Cup before the next blend. A damaged integrated blade requires replacement advice; do not pull it out of the Motor Base.
  • If a new spill appears after correct reassembly and filling below MAX, use the model-specific leak checks before any further blending.

NutriBullet Flip Stainless

Disconnect charging power, wait 90 seconds for shutdown and confirm the blades have stopped. Clean surface spills from the NutriBullet Flip Stainless Motor Base, Blade, and Lid by gently wiping and drying the assembly with a clean cloth. Do not put the entire Motor Base, Blade, and Lid in the dishwasher.

  1. Unplug the NutriBullet Flip Stainless and leave it undisturbed for 90 seconds so it shuts down completely. Confirm the blades have stopped before taking it apart.
  2. Keep the Motor Base, Blade, and Lid on top when removing it from the Blending Cup; empty the cup and wash it with soap and water.
  3. To clean the blade, point the blade downward at an angle. Carefully rinse only the blade area, keeping a thumb or finger over the USB-C port and fingers away from the cutting edges.
  4. To clean the drinking spout, turn the blade upward and gently rinse only the sip hole with warm water, again shielding the USB-C port. Use the included Cleaning Brush for the straw, under the blades, the sip hole and the vent hole.
  5. Gently wipe and dry the Motor Base, Blade, and Lid and the outside of the USB-C port with a clean cloth. Rest the motor assembly upright with the Flip-Top Lid open and let the port become completely dry before charging.
  6. Refit the Blending Cup or Blade Cover for storage so the blades are protected. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire motor assembly, or put the entire Motor Base, Blade, and Lid in the dishwasher.
Does residue remain inside the Blending Cup?
  • For ordinary food residue in an undamaged NutriBullet Flip Stainless with a dry charging connection, the guide also provides an automatic cleaning method.
  • Rinse the cup, add one drop of dish soap and fill it halfway with water. For stubborn residue, let that mixture sit for a few minutes on each end of the cup before starting the cleaning cycle.
  • Secure the motor assembly and close the Flip-Top Lid. Start a blend cycle, then flip and shake the blender to move the soapy water around.
  • After the cycle ends, turn the blender right-side-up, open the drinking lid and empty it. Repeat once using fresh water without soap, then dry the motor assembly upright with the Flip-Top Lid open.
  • Use this method only for the food-contact vessel; it does not clean or repair liquid inside the motor housing.
Is food trapped in the sip hole, vent hole or under the blade?
  • Use the NutriBullet Flip Stainless Cleaning Brush on those accessible areas after shutdown, keeping clear of the sharp blade.
  • Shield the USB-C port during the limited blade-area or sip-hole rinse described above. The whole Motor Base, Blade, and Lid assembly must stay out of the water.
  • If the obstruction cannot be removed through the accessible openings, do not take the motor housing apart or run the blender to dislodge it.

NutriBullet Flip Tritan

Disconnect charging power, wait 90 seconds for shutdown and confirm the blades have stopped. Clean surface spills from the NutriBullet Flip Tritan Motor Base, Blade, and Lid by gently wiping and drying the assembly with a clean cloth. Do not put the entire Motor Base, Blade, and Lid in the dishwasher.

  1. Unplug the NutriBullet Flip Tritan and leave it undisturbed for 90 seconds so it shuts down completely. Confirm the blades have stopped before taking it apart.
  2. Keep the Motor Base, Blade, and Lid on top when removing it from the Blending Cup; empty the cup and wash it with soap and water.
  3. To clean the blade, point the blade downward at an angle. Carefully rinse only the blade area, keeping a thumb or finger over the USB-C port and fingers away from the cutting edges.
  4. To clean the drinking spout, turn the blade upward and gently rinse only the sip hole with warm water, again shielding the USB-C port. Use the included Cleaning Brush for the straw, under the blades, the sip hole and the vent hole.
  5. Gently wipe and dry the Motor Base, Blade, and Lid and the outside of the USB-C port with a clean cloth. Rest the motor assembly upright with the Flip-Top Lid open and let the port become completely dry before charging.
  6. Refit the Blending Cup or Blade Cover for storage so the blades are protected. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire motor assembly, or put the entire Motor Base, Blade, and Lid in the dishwasher.
Does residue remain inside the Blending Cup?
  • For ordinary food residue in an undamaged NutriBullet Flip Tritan with a dry charging connection, the guide also provides an automatic cleaning method.
  • Rinse the cup, add one drop of dish soap and fill it halfway with water. For stubborn residue, let that mixture sit for a few minutes on each end of the cup before starting the cleaning cycle.
  • Secure the motor assembly and close the Flip-Top Lid. Start a blend cycle, then flip and shake the blender to move the soapy water around.
  • After the cycle ends, turn the blender right-side-up, open the drinking lid and empty it. Repeat once using fresh water without soap, then dry the motor assembly upright with the Flip-Top Lid open.
  • Use this method only for the food-contact vessel; it does not clean or repair liquid inside the motor housing.
Is food trapped in the sip hole, vent hole or under the blade?
  • Use the NutriBullet Flip Tritan Cleaning Brush on those accessible areas after shutdown, keeping clear of the sharp blade.
  • Shield the USB-C port during the limited blade-area or sip-hole rinse described above. The whole Motor Base, Blade, and Lid assembly must stay out of the water.
  • If the obstruction cannot be removed through the accessible openings, do not take the motor housing apart or run the blender to dislodge it.

NutriBullet Flex Portable / Flex Portable McLaren

Turn the blender off, disconnect its charging cable and wait for the blade to stop. Wipe ingredient spills from the NutriBullet Flex Portable / Flex Portable McLaren Motor Base with a damp cloth. Keep the Motor Base away from running water.

  1. Turn the NutriBullet Flex Portable / Flex Portable McLaren off, unplug its charging cable and wait for the blade to stop. Keep the Silicone Charge Port Cover in place while cleaning.
  2. Before detaching the Cup, check whether it feels hot or warm. If it does, leave it on the Motor Base without touching or opening it for at least 30 minutes, and longer until cool. Do not blend again.
  3. Once the Cup is cool, slowly open the Sip Lid with Carry Loop away from your face and body and pour the contents into another vessel. Close the lid before taking the empty cup apart.
  4. Grip the Cup and Motor Base and gently twist the Cup off without pulling on the Sip Lid or pushing down. Stand the empty vessel upside down on the flat lid; twist the Blade Block clockwise to remove it, then remove the Sip Lid counter-clockwise.
  5. Hand-wash the Blade Block, Blending Cup and Sip Lid with Carry Loop in warm soapy water, then rinse them. Wipe ingredient spills from the Motor Base with a damp cloth. NEVER submerge the motor base in water. Do not put the motor base under running water.
  6. Remove excess water from the lidโ€™s gasket area and gently guide its gasket back into place if it moved. Allow the lid to air-dry fully and dry the Blade Block completely.
  7. Insert the Blade Block through the bottom of the Cup and twist counter-clockwise to its soft-stop. Refit the Sip Lid clockwise, click the Sip Cap shut, then gently twist the Cup and Blade Block into the Motor Base without force. Store upright with the blades covered by the Cup.
Did the Sip Lid gasket move or trap water during cleaning?
  • Inspect the NutriBullet Flex Portable / Flex Portable McLaren Sip Lid with Carry Loop around its gasket before putting the lid away.
  • Remove excess moisture and gently return a displaced gasket to its seat. Keep the lid open for air-drying so no moisture stays trapped around the sealing area.
  • After the lid has dried, close the Sip Cap until it clicks. If the gasket or lid is damaged rather than displaced, replace the affected detachable part.
Is solid food still trapped in the Blade Block?
  • Keep the NutriBullet Flex Portable / Flex Portable McLaren off with the charger unplugged. Follow the cooling and emptying steps above before detaching the Cup from the Motor Base and standing the empty vessel upside down on the flat Sip Lid.
  • Carefully remove the Blade Block clockwise and clear the accessible obstruction with the Blade Block removed. Do not put a hand or utensil inside the Cup to clear a blockage.
  • Wash and dry the Blade Block before refitting it. If the blade is bent or damaged, stop using it and obtain the correct replacement instead of trying to straighten it.

NutriBullet GO

Turn the blender off, disconnect its USB cable and wait for the blades to stop. Wipe accessible food residue from the NutriBullet GO Motor Base and blade assembly with a damp sponge or cloth and dry the spill before use; do not put the Motor Base under running water or the blade assembly in the dishwasher.

  1. Turn the NutriBullet GO off and disconnect its USB cable. Wait until the motor and blades have completely stopped before handling the cup.
  2. For cool contents, invert the assembled blender so the Cup is upright, then twist the Motor Base anti-clockwise off the Cup. If the vessel feels warm, let it cool before carefully untwisting the blade with the opening away from your body.
  3. Empty the Cup and hand-wash it and its lid with warm soapy water, then rinse.
  4. Gently rinse only the blade assembly and carefully clean it with a damp sponge or cloth, keeping away from the sharp edges. NEVER submerge the motor base in water. Do not run the motor base directly under water; the blade assembly must not go in the dishwasher.
  5. Clean and dry spilled mixture on the blender and on the surrounding work surface before using it again. The guide says not to operate the NutriBullet GO when wet.
  6. Secure the Blade Cover onto the Motor Base when the Cup is removed for storage, and keep all parts together where they cannot be damaged.
Has mixture spread under or around the blender?
  • The NutriBullet GO guide requires significant spillage on the appliance or work surface to be cleaned and dried before use continues.
  • With the blender off, remove food from the accessible surfaces using the cleaning method above. Check the surface beneath and next to the blender is dry before putting the base back down.
  • If the spill has entered the motor housing or charging slot, leave the blender off for support advice; cleaning the worktop does not remove liquid inside an electrical assembly.
Does food remain on the blade after rinsing?
  • Clean accessible food from the NutriBullet GO blade assembly with a damp sponge or cloth while the motor is off.
  • Keep the Motor Base outside the direct water stream and never put the motor-and-blade assembly in the dishwasher.
  • If removal would require servicing or opening the Motor Base, stop there; the guide prohibits attempting to repair or service the appliance.

NutriBullet Juicer 800W

Unplug the appliance and wait for all movement to stop before cleaning. Clean spills from the exposed NutriBullet Juicer 800W Motor Base with a clean damp cloth, then allow it to dry completely.

  1. Switch off, unplug and wait for the Sieve to stop. Remove the Juice Pitcher; on NBJ07100 lower the No-Drip Spout cover.
  2. Lower the Locking Handle away from the Basin Cover ears. Lift the Pulp Basin with its cover and Sieve off the Motor Base and take the assembly to the sink.
  3. Lift out the Food Pusher and Basin Cover, lift the Sieve by its top edges and empty the pulp. Keep clear of the sharp Sieve teeth.
  4. Wipe the exposed Motor Base and surrounding spill with a clean damp cloth. NEVER submerge the motor base in water. Do not rinse the Motor Base.
  5. Hand-wash the removed parts in warm soapy water. Scrub the Sieve under running water with the Cleaning Brush; for dried pulp, soak only the Sieve in hot water for 30 minutes, then brush and rinse.
  6. Allow the Motor Base and cleaned parts to dry completely. Seat the Pulp Basin, click the Sieve onto the drive coupling, align the cover ears and raise the Locking Handle into its locked upright position.
Is the residue on the accessible Motor Base?
  • Use the cleaning sequence above for a surface spill. Inspect the dry exposed surface before putting the juicing assembly back.
  • If liquid has run through an opening or remains under the housing, keep the juicer off and follow the liquid-in-base advice at the end.
Is pulp blocking a detachable juicing part?
  • Keep the Motor Base separate while washing. Remove the pulp from the detachable screen, bowl and outlets using the supplied Cleaning Brush.
  • Check the cleaned openings before refitting. Repeat the appropriate cleaning step if pulp remains; replace a cracked or damaged detachable part.

NutriBullet Cold Press Slow Juicer

Unplug the appliance and wait for all movement to stop before cleaning. Remove spills from the outside of the NutriBullet Cold Press Slow Juicer Motor Base with a clean damp cloth and dry it thoroughly.

  1. Switch OFF, unplug and allow complete cooling. Wait for every moving part to stop before removing the Juice Container; close the juice spout cover and remove the Pulp Container.
  2. Turn the Juice Bowl Cover anticlockwise and lift it off. Lift out the Auger, remove the Juice Bowl, then separate the Juicing Screen from the Rotating Bowl Brush.
  3. Empty the containers and wash the detachable parts in warm soapy water. Hand-wash the Auger with a soft cloth; use the Cleaning Brush under running water on the sharp Juicing Screen.
  4. Pull the pulp plug out of the pulp spout. Use the narrow end of the Cleaning Brush to remove trapped pulp and run water through the detached bowl and spout.
  5. Wipe the outside of the Motor Base with a clean damp cloth. NEVER submerge the motor base in water. Dry every part thoroughly before putting the pulp plug back into position.
  6. Seat the Juice Bowl, screen and Rotating Bowl Brush, then turn and press the Auger onto the centre axis. Turn the cover clockwise until the locked symbol aligns with the triangle; put the containers below their spouts.
Is the residue on the accessible Motor Base?
  • Use the cleaning sequence above for a surface spill. Inspect the dry exposed surface before putting the juicing assembly back.
  • If liquid has run through an opening or remains under the housing, keep the juicer off and follow the liquid-in-base advice at the end.
Is pulp blocking a detachable juicing part?
  • Keep the Motor Base separate while washing. Remove the pulp from the detachable screen, bowl and outlets using the supplied Cleaning Brush.
  • Check the cleaned openings before refitting. Repeat the appropriate cleaning step if pulp remains; replace a cracked or damaged detachable part.

NutriBullet Juicer Pro 1000W

Unplug the appliance and wait for all movement to stop before cleaning. Clean spills from the exposed NutriBullet Juicer Pro 1000W Motor Base with a clean damp cloth, then allow it to dry completely.

  1. Switch off, unplug and wait for the Sieve to stop. Remove the Juice Pitcher and close the No-Drip Spout cover.
  2. Lower the Locking Handle away from the Basin Cover ears. Lift the Pulp Basin with its cover and Sieve off the Motor Base and take the assembly to the sink.
  3. Lift out the Food Pusher and Basin Cover, lift the Sieve by its top edges and empty the pulp. Keep clear of the sharp Sieve teeth.
  4. Wipe the exposed Motor Base and surrounding spill with a clean damp cloth. NEVER submerge the motor base in water. Do not rinse the Motor Base.
  5. Hand-wash the removed parts in warm soapy water. Scrub the Sieve under running water with the Cleaning Brush; for dried pulp, soak only the Sieve in hot water for 30 minutes, then brush and rinse.
  6. Allow the Motor Base and cleaned parts to dry completely. Seat the Pulp Basin, click the Sieve onto the drive coupling, align the cover ears and raise the Locking Handle into its locked upright position.
Is the residue on the accessible Motor Base?
  • Use the cleaning sequence above for a surface spill. Inspect the dry exposed surface before putting the juicing assembly back.
  • If liquid has run through an opening or remains under the housing, keep the juicer off and follow the liquid-in-base advice at the end.
Is pulp blocking a detachable juicing part?
  • Keep the Motor Base separate while washing. Remove the pulp from the detachable screen, bowl and outlets using the supplied Cleaning Brush.
  • Check the cleaned openings before refitting. Repeat the appropriate cleaning step if pulp remains; replace a cracked or damaged detachable part.

NutriBullet Cold Press Batch Juicer

Unplug the appliance and wait for all movement to stop before cleaning. Clean spills from the NutriBullet Cold Press Batch Juicer Motor Base with a clean damp cloth and dry it before use. Do not put the motor base in the dishwasher.

  1. Turn the Dial OFF, unplug and wait for the Auger to stop.
  2. Open the Lid, turn the Hopper anticlockwise and lift it away. Pull the Auger straight up, then lift the Juicing Bowl off the Motor Base and empty the Hopper and bowl.
  3. Rinse the detachable parts under running water. Use the Cleaning Brush to scrub residue from the Auger, Hopper and Juicing Bowl; hand-wash with warm soapy water without metal sponges or abrasive pads.
  4. Remove remaining residue from the underside, outlets and cover of the detached Juicing Bowl. Push the Silicone Cover firmly back in until it sits flush.
  5. Wipe the Motor Base with a clean damp cloth. NEVER submerge the motor base in water. Do not put the motor base in the dishwasher; clean and dry the spill before using the juicer again.
  6. Refit the Juicing Bowl with its spouts in the base notches. Press the Auger to the bottom, fit the Hopper with the Lid open and twist clockwise until the orange dot disappears; close the Lid.
Is the residue on the accessible Motor Base?
  • Use the cleaning sequence above for a surface spill. Inspect the dry exposed surface before putting the juicing assembly back.
  • If liquid has run through an opening or remains under the housing, keep the juicer off and follow the liquid-in-base advice at the end.
Is pulp blocking a detachable juicing part?
  • Keep the Motor Base separate while washing. Remove the pulp from the detachable screen, bowl and outlets using the supplied Cleaning Brush.
  • Check the cleaned openings before refitting. Repeat the appropriate cleaning step if pulp remains; replace a cracked or damaged detachable part.

NutriBullet CrispLite Air Fryer 6L

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet CrispLite Air Fryer 6L Base inner wall with a warm cotton cloth, dry it with a dry cloth and wipe the exterior with a damp cloth.

  1. Turn the NutriBullet CrispLite Air Fryer 6L OFF, unplug it and let it cool thoroughly before touching its inner surfaces.
  2. Remove the Cooking Basket and 3-in-1 Tray. Wash these detached parts with warm soapy water; avoid abrasive or metal tools that can damage the coating.
  3. Wipe residue from the inner wall of the Air Fryer Base with a warm cotton cloth, then dry with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water.
  4. If food remains on the cooled heating element, remove it gently with a soft-to-medium bristle brush.
  5. Dry the Cooking Basket and 3-in-1 Tray thoroughly, then refit the parts correctly. Clean and dry the surrounding work surface before using the air fryer again.
Is food still stuck to the cooled inner wall?
  • Wipe the accessible inner wall with a warm cotton cloth and dry it with a dry cloth. Wash the removed basket and tray separately.
  • If residue remains beyond the surfaces you can reach without dismantling the housing, leave the appliance off.

NutriBullet XXL Digital Air Fryer 7L

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet XXL Digital Air Fryer 7L Base inner wall with a warm cotton cloth, dry it with a dry cloth and wipe the exterior with a damp cloth.

  1. Turn the NutriBullet XXL Digital Air Fryer 7L OFF, unplug it and let it cool thoroughly before touching its inner surfaces.
  2. Remove the Cooking Basket and Crisping Tray. Wash these detached parts with warm soapy water; avoid abrasive or metal tools that can damage the coating.
  3. Wipe residue from the inner wall of the Air Fryer Base with a warm cotton cloth, then dry with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water.
  4. Dry the Cooking Basket and Crisping Tray thoroughly, then refit the parts correctly. Clean and dry the surrounding work surface before using the air fryer again.
Is food still stuck to the cooled inner wall?
  • Wipe the accessible inner wall with a warm cotton cloth and dry it with a dry cloth. Wash the removed basket and tray separately.
  • If residue remains beyond the surfaces you can reach without dismantling the housing, leave the appliance off.

NutriBullet Twin Drawer Air Fryer

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet Twin Drawer Air Fryer Base inner wall with a warm cotton cloth, dry it with a dry cloth and wipe the exterior with a damp cloth.

  1. Turn the NutriBullet Twin Drawer Air Fryer OFF, unplug it and let it cool thoroughly before touching its inner surfaces.
  2. Remove the Cooking Drawers and Crisping Trays. Wash these detached parts with warm soapy water; avoid abrasive or metal tools that can damage the coating.
  3. Wipe residue from the inner wall of the Air Fryer Base with a warm cotton cloth, then dry with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water.
  4. Dry the Cooking Drawers and Crisping Trays thoroughly, then refit the parts correctly. Clean and dry the surrounding work surface before using the air fryer again.
Is food still stuck to the cooled inner wall?
  • Wipe the accessible inner wall with a warm cotton cloth and dry it with a dry cloth. Wash the removed basket and tray separately.
  • If residue remains beyond the surfaces you can reach without dismantling the housing, leave the appliance off.

NutriBullet CrispLite Vision Air Fryer 8L

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet CrispLite Vision Air Fryer 8L Base inner wall with a warm cotton cloth, dry it with a dry cloth and wipe the exterior with a damp cloth.

  1. Turn the NutriBullet CrispLite Vision Air Fryer 8L OFF, unplug it and let it cool thoroughly before touching its inner surfaces.
  2. Remove the Cooking Basket and 3-in-1 Tray. Wash these detached parts with warm soapy water; avoid abrasive or metal tools that can damage the coating.
  3. Wipe residue from the inner wall of the Air Fryer Base with a warm cotton cloth, then dry with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water.
  4. If food remains on the cooled heating element, remove it gently with a soft-to-medium bristle brush.
  5. Dry the Cooking Basket and 3-in-1 Tray thoroughly, then refit the parts correctly. Clean and dry the surrounding work surface before using the air fryer again.
Is food still stuck to the cooled inner wall?
  • Wipe the accessible inner wall with a warm cotton cloth and dry it with a dry cloth. Wash the removed basket and tray separately.
  • If residue remains beyond the surfaces you can reach without dismantling the housing, leave the appliance off.

NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L Base inner wall with a warm cotton cloth, dry it with a dry cloth and wipe the exterior with a damp cloth.

  1. Turn the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L OFF, unplug it and let it cool thoroughly before touching its inner surfaces.
  2. Remove the Cooking Basket and Crisping Tray and Wire Rack. Wash these detached parts with warm soapy water; avoid abrasive or metal tools that can damage the coating.
  3. Wipe residue from the inner wall of the Air Fryer Base with a warm cotton cloth, then dry with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water.
  4. If food remains on the cooled heating element, remove it gently with a soft-to-medium bristle brush.
  5. Dry the Cooking Basket and Crisping Tray and Wire Rack thoroughly, then refit the parts correctly. Clean and dry the surrounding work surface before using the air fryer again.
Is food still stuck to the cooled inner wall?
  • Wipe the accessible inner wall with a warm cotton cloth and dry it with a dry cloth. Wash the removed basket and tray separately.
  • If residue remains beyond the surfaces you can reach without dismantling the housing, leave the appliance off.

NutriBullet Immersion Blender 800W

Unplug the appliance and wait for all movement to stop before cleaning. Wipe spills from the NutriBullet Immersion Blender 800W motor body with a damp cloth and dry it thoroughly; wash the detached washable attachments separately with warm soapy water.

  1. Release the power button, unplug the NutriBullet Immersion Blender 800W and wait until the blade or whisk has stopped. Lift the attachment out of the mixing vessel only after movement stops.
  2. Detach the motor body from the blending arm, whisk or chopping bowl attachment. Separate the whisk from its holder; for the chopper, remove the lid and lift the S-blade by its upper plastic part before emptying the bowl.
  3. Wash the chopping bowl, whisk, blending cup and S-blade with warm soapy water. Clean the blending arm, whisk holder and chopping bowl lid with warm soapy water without soaking or putting them in the dishwasher.
  4. Wipe the motor body with a damp cloth. Dry all parts thoroughly before reassembly. Fit the chosen attachment tightly to the motor body and check that it is locked in place. NEVER submerge the main unit in water.
Is a thick mixture trapping the blade or whisk?
  • With the NutriBullet Immersion Blender 800W off and unplugged, inspect the mixture after all movement has stopped.
  • Remove some mixture or add suitable liquid to loosen it; separate clumps only with the attachment safely detached. Refit the attachment securely and check that the mixture can move around it before resuming.
Is food stuck on the cutting area or whisk?
  • Detach the NutriBullet Immersion Blender 800W attachment after unplugging and stopping. Rinse residue from the blade or whisk with warm water and clean with warm soapy water.
  • For dried residue on the cup, bowl, removable whisk or S-blade, soak the affected washable part in hot water for 30 minutes and then clean it. Do not soak the chopping bowl lid, whisk holder or blending arm. Dry completely before refitting; replace a damaged part.

NutriBullet EveryGrain Cooker

Switch off, unplug and let the appliance cool completely before cleaning. Clean the cooled NutriBullet EveryGrain Cooker inner heating plate and Cooker Base with a clean damp cloth; hand-wash the Cooking Pot separately with warm soapy water.

  1. Switch off and unplug the NutriBullet EveryGrain Cooker and allow the cooker and heating plate to cool completely before cleaning. Remove the Cooking Pot and Steaming Basket, if used, and empty leftover food.
  2. Hand-wash the Cooking Pot with warm soapy water to protect its nonstick coating. Wash the Steaming Basket, Spatula and Measuring Scoop with warm soapy water or in the dishwasher.
  3. Wipe the cooled inner heating plate and Cooker Base with a clean, damp cloth. Wipe the Sealing Panel and Condensation Collector with a damp cloth or sponge and warm soapy water. NEVER submerge the main unit in water.
  4. Remove the Steam Vent plug and rinse it in warm water; clean the inside of the Steam Vent with a damp cloth. Clear visible residue and dry cleaned surfaces before reuse. Do not use steel wool.
  5. Seat the Cooking Pot level on the inner heating plate. If fitting the Steaming Basket, make sure it sits level in the top of the pot without force. Close the Cooker Lid until it clicks; if a component is damaged or will not fit, keep the cooker off.
Is food stuck to the Cooking Pot?
  • Fill the cooled NutriBullet EveryGrain Cooker Cooking Pot with water and let the residue soak. Warm soapy water helps loosen the deposits.
  • For stubborn residue, apply dishwashing liquid directly to the food for a few minutes before soaking. Hand-wash without steel wool so the nonstick coating is protected. If food remains, repeat the soak instead of scraping the coating.
Is residue trapped in the vent, sealing panel or condensation collector?
  • Once the NutriBullet EveryGrain Cooker is unplugged and cool, remove the Steam Vent plug and rinse it with warm water. Wipe inside the Steam Vent with a damp cloth.
  • Clean the Sealing Panel and Condensation Collector with a damp cloth or sponge and warm soapy water after every use. Leave the surfaces clean and dry before cooking again; do not scrape them with steel wool.

NutriBullet Food Processor

Unplug the appliance and wait for all movement to stop before cleaning. Clean surface spills from the NutriBullet Food Processor Motor Base with a cloth or sponge dampened with warm soapy water, leaving all base pieces in place.

  1. Turn NutriBullet Food Processor off, unplug it and wait until the blade or disc has completely stopped. Turn the Work Bowl handle counterclockwise, lift the bowl off the Motor Base and set it on a flat surface.
  2. Turn the Work Bowl Lid counterclockwise to remove it. Lift the blade or disc by its plastic centre, keeping fingers away from cutting edges; do not tip a blade out onto your hand. Remove food with a spatula or spoon.
  3. Wash detachable parts with warm soapy water, or use the top dishwasher rack without a heat or sanitise cycle. Include the Blade Adaptor, attachments and Dual-Size Food Pusher.
  4. Wipe the Motor Base with a sponge or cloth dampened with warm soapy water. A small brush may clean accessible actuator areas; do not remove any base pieces. Wipe away leakage residue with a damp sponge and warm water.
  5. Before reassembly, check the bowl, lid and blade for damage. Fit the blade or disc, then turn the lid clockwise until its markings align with the handle; turn the assembled bowl clockwise onto the Motor Base until it clicks. Keep a damaged or unlocked assembly out of use.
Is a piece of food blocking the Feed Chute?
  • Switch NutriBullet Food Processor off, unplug it and wait for the blade or disc to stop. Unlock and remove the Work Bowl Lid.
  • Use the Food Pusher, a spatula or spoon to remove trapped food from the detached lid. Wash residue away, refit the lid with the markings aligned, and verify the chute is clear before restarting.
Has processed food reached the underside of the disc?
  • Look at the NutriBullet Food Processor Work Bowl without removing the lid while the disc is moving. Food just below the disc can stop more food entering.
  • Switch off, unplug and wait for a full stop. Remove the bowl and lid, lift the disc by its plastic centre, and empty the bowl with a spoon or spatula. Refit the disc and lock the lid and bowl before processing another smaller batch.
Is food dried around the exposed base or actuator area?
  • Keep NutriBullet Food Processor unplugged with the Work Bowl removed. Wipe the Motor Base using a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water.
  • Use a small brush only on the accessible actuator area if needed. Wipe away residue with a damp sponge and warm water; do not remove pieces from the base. If a part is damaged, replace the detachable part before use.

NutriBullet Chill

Unplug the appliance and wait for all movement to stop before cleaning. Clean spills from the NutriBullet Chill Motor Base with a damp sponge or cloth and mild soapy water; keep liquid away from the drive shaft and centre hole.

  1. Unplug the NutriBullet Chill and wait for all movement to stop. Hold the release button and turn the Pint Cup counterclockwise to remove it from the Motor Base.
  2. Keep the Pint Cup upright and turn the Blade Block counterclockwise to lift it off. Handle the blade holder by its plastic grip, keeping fingers away from the blade and shaft, which may be hot.
  3. Empty the Pint Cup. Hand-wash the Pint Cup, lid, Blade, Blade Block and Shaft with warm soapy water, gently cleaning the circular Blade Block opening and around the shaft with a sponge.
  4. Wipe the Motor Base with a damp sponge or cloth and mild soapy water. A cleaning brush can remove food around the cup attachment area; keep liquid away from the drive shaft and centre hole.
  5. Dry every part, including the inside and outside of the Blade Shaft, before fitting it to the base. For storage, attach the Blade Cover or attach the blade to the Pint Cup; do not leave the blade exposed.
Is residue inside the Blade Block opening or around the Shaft?
  • With the NutriBullet Chill unplugged and the blade holder removed, use a sponge and dish soap to clean the circular opening on the Blade Block and around the Shaft.
  • Rinse the washable components and dry the Shaft inside and out before assembly. For dishwasher cleaning, remove the Blade from the Blade Block and use the top rack without a sanitise cycle.
Is food dried on the cup rim or base attachment area?
  • Wipe the NutriBullet Chill Pint Cup inner rim with a towel before refreezing leftovers so the Blade Block can fit after freezing.
  • For the unplugged Motor Base, use a damp cloth and mild soapy water, with a brush around the cup attachment area if needed. Keep cleaning liquid away from the drive shaft and centre hole; finish with clean, dry parts. NEVER submerge the motor base in water.

NutriBullet Limitless Food Processor

Unplug the appliance and wait for all movement to stop before cleaning. Clean surface spills from the NutriBullet Limitless Food Processor Motor Base with a cloth or sponge dampened with warm soapy water, leaving all base pieces in place.

  1. Turn NutriBullet Limitless Food Processor off, unplug it and wait until the blade or disc has completely stopped. Turn the Work Bowl handle counterclockwise, lift the bowl off the Motor Base and set it on a flat surface.
  2. Turn the Work Bowl Lid counterclockwise to remove it. Lift the blade or disc by its plastic centre, keeping fingers away from cutting edges; do not tip a blade out onto your hand. Remove food with a spatula or spoon.
  3. Wash detachable parts with warm soapy water, or use the top dishwasher rack without a heat or sanitise cycle. Clean the Endless Chute and Slinger Disc too if they were used.
  4. Wipe the Motor Base with a sponge or cloth dampened with warm soapy water. A small brush may clean accessible actuator areas; do not remove any base pieces. Wipe away leakage residue with a damp sponge and warm water.
  5. Before reassembly, check the bowl, lid and blade for damage. Fit the blade or disc, then turn the lid clockwise until its markings align with the handle; turn the assembled bowl clockwise onto the Motor Base until it clicks. Keep a damaged or unlocked assembly out of use.
Is a piece of food blocking the Feed Chute?
  • Switch NutriBullet Limitless Food Processor off, unplug it and wait for the blade or disc to stop. Unlock and remove the Work Bowl Lid.
  • Use the Food Pusher, a spatula or spoon to remove trapped food from the detached lid. Wash residue away, refit the lid with the markings aligned, and verify the chute is clear before restarting.
Has processed food reached the underside of the disc?
  • Look at the NutriBullet Limitless Food Processor Work Bowl without removing the lid while the disc is moving. Food just below the disc can stop more food entering.
  • Switch off, unplug and wait for a full stop. Remove the bowl and lid, lift the disc by its plastic centre, and empty the bowl with a spoon or spatula. Refit the disc and lock the lid and bowl before processing another smaller batch.
Is food dried around the exposed base or actuator area?
  • Keep NutriBullet Limitless Food Processor unplugged with the Work Bowl removed. Wipe the Motor Base using a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water.
  • Use a small brush only on the accessible actuator area if needed. Wipe away residue with a damp sponge and warm water; do not remove pieces from the base. If a part is damaged, replace the detachable part before use.

NutriBullet Baby

Unplug the appliance and wait for all movement to stop before cleaning. Clean accessible spills inside and outside the NutriBullet Baby Motor Base with a damp rag; use a warm soapy cloth for an external spill and let the base dry completely before use.

  1. Unplug the NutriBullet Baby and wait until all movement stops. Twist the cup or Batchbowl assembly counterclockwise off the Motor Base and keep the vessel upright before unscrewing the extractor blade.
  2. Empty the vessel. Hand-wash the cups or Batchbowl with warm soapy water and rinse, or place them on the top dishwasher rack. Hand-wash the extractor blade and leave its seal in place; the blade is not dishwasher safe.
  3. Wipe the accessible inside and outside of the Motor Base with a damp rag. For an external spill, use a warm soapy cloth and allow the base to dry completely before operating.
  4. Check the blade seal is completely seated and that the vessel and blade are undamaged. Twist the extractor blade onto the cup or Batchbowl until sealed; for the Batchbowl, fit the lid firmly and lock in its vented cap before blending.
Is dried food stuck to the cup or blade?
  • For a NutriBullet Baby with an intact, correctly sealed cup and blade and a clean, dry Motor Base, fill the cup halfway with soapy water, twist on the blade and blend for 10โ€“20 seconds.
  • Unplug, remove the assembly and stand the cup upright. Unscrew the blade, pour out the water, then lightly scrub and rinse remaining debris. If the vessel or blade leaks or is damaged, hand-wash and replace the faulty part instead of running a cleaning blend. Buy a replacement extractor blade in Australia or New Zealand.
Is the spill confined to the accessible Motor Base surfaces?
  • Keep the NutriBullet Baby unplugged. Wipe the accessible inner and outer base surfaces with a warm soapy cloth.
  • Allow the Motor Base to dry completely before use. NEVER submerge the motor base in water. If liquid has reached inside the housing, use the liquid-inside-base advice in this article.

NutriBullet Baby Steam + Blend

Switch off and unplug; wait at least ten minutes, until the appliance is completely cool and the blade has stopped. Clean spills from the NutriBullet Baby Steam + Blend Motor Base with a clean damp cloth and dry it fully; wash the detached Work Bowl, lid pieces, Blending Blade and Blade Holder separately with warm soapy water.

  1. Turn off and unplug the NutriBullet Baby Steam + Blend. Allow at least ten minutes and wait until the appliance has cooled completely and the blade has stopped before disassembly.
  2. Turn the Work Bowl clockwise to unlock it from the Motor Base. Open the Work Bowl Lid; twist the circular grip on the lid underside counterclockwise to separate the two lid pieces and drain trapped food or water.
  3. Lift the Blending Blade vertically by a non-sharp area, using a mitt if needed, and empty the Work Bowl. Unscrew the Water Reservoir Cap and empty remaining water.
  4. Wash the Work Bowl, lid pieces, Blending Blade and Blade Holder with warm soapy water. Use a soft cloth or brush to remove food, including inside the Blade Stem. Keep the Blending Blade and Blade Holder out of the dishwasher.
  5. Wipe the Motor Base with a clean, damp cloth and dry the cleaned parts fully. Lower the Blending Blade vertically onto the Blade Holder, fit the lid clockwise, then turn the Work Bowl counterclockwise onto the Motor Base until secure.
Is food or water trapped inside the two-piece lid or Blade Stem?
  • With the NutriBullet Baby Steam + Blend cool and unplugged, separate the Work Bowl Lid using its underside grip and drain the trapped contents.
  • Clean both lid pieces and inside the Blade Stem with a soft cloth or brush, then dry fully. Rinse the Blending Blade by holding a non-sharp area; wash the Blade Holder by hand.
Has food dried onto a removable part?
  • Clean the NutriBullet Baby Steam + Blend Work Bowl, lid and Blending Blade promptly after cooling. If food has dried onto one of these parts, soak the affected detachable part in hot water for 30 minutes.
  • Wash and rinse the loosened residue and dry thoroughly. Use warm soapy water for the Blade Holder; the Motor Base is wiped only. If residue remains, repeat gentle hand-cleaning instead of scraping with a sharp tool. NEVER submerge the motor base in water.

Magic Bullet To Go 200W

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the Magic Bullet To Go 200W Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the Magic Bullet To Go 200W, then wait until every moving part has stopped.
  2. Remove the cup and Cross Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible Magic Bullet To Go 200W Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached Magic Bullet To Go 200W Cross Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the Magic Bullet To Go 200W cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

Magic Bullet Value Pack 200W

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the Magic Bullet Value Pack 200W Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the Magic Bullet Value Pack 200W, then wait until every moving part has stopped.
  2. Remove the cup and Cross Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible Magic Bullet Value Pack 200W Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached Magic Bullet Value Pack 200W Cross Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it. Buy a replacement extractor blade in Australia or New Zealand.
Is food dried onto the cup or pitcher?
  • For dried food in the Magic Bullet Value Pack 200W cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

Magic Bullet Blender Combo

Unplug the appliance and wait for all movement to stop before cleaning. Clean surface spills from the Magic Bullet Blender Combo Motor Base with a damp sponge or cloth. Leave its parts in place.

  1. Switch off and unplug the Magic Bullet Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and Cross Blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the Magic Bullet Blender Combo Motor Base surface with a damp sponge or cloth. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
  4. Use a small dry brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Is food stuck to the detached blade?
  • Inspect the detached Magic Bullet Blender Combo Cross Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food dried onto the cup or pitcher?
  • For dried food in the Magic Bullet Blender Combo cup or pitcher, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

Magic Bullet Mini Juicer

Unplug the appliance and wait for all movement to stop before cleaning. Clean surface spills from the Magic Bullet Mini Juicer Motor Base and the surrounding area with a clean damp cloth.

  1. Set the Power Button to OFF, unplug and wait for the Sieve to stop. Tilt the Juice Cup forward and slide it out, then turn the Silicone Spout Cap upwards.
  2. Release both Locking Arms by pushing their bottom ends up and letting them fall away. Unsnap the Pulp Bin, lift the Juice Bowl Cover and remove the Juice Bowl and Sieve, holding the Sieve by its edges.
  3. Empty the pulp and rinse the removable parts. Scrub the Sieve under running water with the Cleaning Brush, outside first and then inside; do not touch the blade teeth.
  4. Wipe the Motor Base and surrounding spill with a clean damp cloth. NEVER submerge the motor base in water. Hand-wash detached parts with warm soapy water.
  5. For dried Sieve residue, soak the Sieve in hot water for 30 minutes and brush again. Clean and dry the spill before reassembly.
  6. Seat the Juice Bowl and click the Sieve onto the coupling. Fit the cover, lock both arms upright, snap the Pulp Bin underneath the back of the cover and position the Juice Cup under the spout.
Is the residue on the accessible Motor Base?
  • Use the cleaning sequence above for a surface spill. Inspect the dry exposed surface before putting the juicing assembly back.
  • If liquid has run through an opening or remains under the housing, keep the juicer off and follow the liquid-in-base advice at the end.
Is pulp blocking a detachable juicing part?
  • Keep the Motor Base separate while washing. Remove the pulp from the detachable screen, bowl and outlets using the supplied Cleaning Brush.
  • Check the cleaned openings before refitting. Repeat the appropriate cleaning step if pulp remains; replace a cracked or damaged detachable part.

Magic Bullet Kitchen Express 250W

Unplug the appliance and wait for all movement to stop before cleaning. Wipe spills from the Magic Bullet Kitchen Express 250W Motor Base with a damp sponge or cloth, keeping the Motor Base assembled.

  1. Switch off and unplug the Magic Bullet Kitchen Express 250W, then wait until every moving part has stopped.
  2. For the blending cup, turn the cup/cross blade assembly counter-clockwise off the base and turn it upright before unscrewing the blade. For the Work Bowl, turn the bowl counter-clockwise off the base and set it on a clean, dry, flat surface, then unlock its lid counter-clockwise; remove the chopping blade before emptying food, or lift a disc using its two larger finger holes.
  3. Use a damp sponge or cloth to wipe the Magic Bullet Kitchen Express 250W Motor Base clean without dismantling it.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade or bowl attachments separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting. NEVER submerge the motor base in water.
Is food dried onto the cup or pitcher?
  • For dried food in the Magic Bullet Kitchen Express 250W cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

Magic Bullet Air Fryer 2.5L

Switch off, unplug and let the appliance cool completely before cleaning. Wipe spills from the exterior of the Magic Bullet Air Fryer 2.5L Base with a clean damp cloth. Rinse the detached Fry Pot and Crisping Tray separately with hot soapy water.

  1. Set the Magic Bullet Air Fryer 2.5L timer and temperature control to 0, unplug it and allow the heating element to cool completely. The orange indicator light should no longer be illuminated.
  2. Remove the Fry Pot from the Base. Inspect the pot for food scraps, then pull out the Crisping Tray by its centre handle and remove food from the tray; take care around its sharp edges.
  3. Rinse the detached Fry Pot and Crisping Tray with hot soapy water. Wipe the exterior of the Air Fryer Base with a clean damp cloth. NEVER submerge the main unit in water.
  4. Clean and dry the spill and the work surface. Refit the Fry Pot securely until it clicks; do not use the appliance while wet.
Is food left on the Fry Pot or Crisping Tray?
  • After cooling and removing the Magic Bullet Air Fryer 2.5L Fry Pot, lift the Crisping Tray out by its centre handle.
  • Remove remaining scraps and wash both parts with hot soapy water. Clean these parts after each use so residue does not harden onto them; leave the base closed.

NutriBullet Ultra Plus+ Compact Kitchen System

Unplug the appliance and wait for all movement to stop before cleaning. Wipe spills gently from the NutriBullet Ultra Plus+ Compact Kitchen System Motor Base exterior with a damp sponge or cloth and dry it with a clean cloth; leave the housing closed.

  1. Power off and unplug the NutriBullet Ultra Plus+ Compact Kitchen System and wait until every blade or disc has stopped. For the blending cup, remove the cup and Rapid Extractor Blade assembly from the base; stand the cup upright before unscrewing the blade.
  2. For the Processor Attachment, turn the Work Bowl Lid counterclockwise and lift it off first. Then turn the Work Bowl and Processor Base counterclockwise off the Motor Base. Lift the blade or disc by its central plastic knob before removing food with a spoon or spatula.
  3. Separate the processor Work Bowl from its Processor Base by holding the base underneath and turning the bowl counterclockwise. Wash the blade, disc, Work Bowl and lid by hand with a sponge or cloth, soap and water, or on the top dishwasher rack without heat/sanitise. Hand-wash the Processor Base and Blade Adapter.
  4. For the Coffee & Dry Spice Grinder, disengage it from the Motor Base and separate the Grinding Cup and Grinder Blade. Hand-wash with a sponge or cloth, soap and water, or use the top dishwasher rack without heat/sanitise.
  5. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to lift residue from it. Wipe the Motor Base exterior gently with a damp sponge or cloth and dry with a clean cloth; do not open the housing. NEVER submerge the motor base in water.
  6. Inspect cleaned parts for cracks, warping, cloudiness or a damaged blade gasket before reassembly. Replace damaged detachable parts; secure the Rapid Extractor Blade tightly on the cup, or reassemble the chosen attachment in the reverse of its removal order. Buy a replacement extractor blade in Australia or New Zealand.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Are ingredients stuck to the Cup or Rapid Extractor Blade?
  • For an intact NutriBullet Ultra Plus+ Compact Kitchen System cup and blade with a clean, dry base, add room-temperature water up to MAX and one or two drops of dish soap. Twist the blade on securely and blend for 20โ€“30 seconds.
  • Unplug, remove and open the assembly, then scrub remaining residue away with soap and water. A leaking or damaged assembly must be hand-washed and repaired by replacing the affected detachable part before any cleaning blend.
Is food packed into the Processor Feed Chute?
  • Power off and unplug the NutriBullet Ultra Plus+ Compact Kitchen System, then wait until the disc or blade stops. Remove the lid before attempting to unlock the Work Bowl assembly.
  • Clear the Feed Chute and remove accumulated food from the bowl after lifting out the blade or disc by its plastic centre. Reassemble with the correct disc side facing up and its hash marks aligned with the Blade Adapter; the disc should sit nearly flush with the bowl rim. Feed the next batch slowly.
Is stubborn residue stuck to a processor blade or disc?
  • Remove the NutriBullet Ultra Plus+ Compact Kitchen System blade or disc only after shutdown and disassembly, holding the plastic centre.
  • Immerse the detached blade or disc in room-temperature water with one or two drops of dish soap for 20โ€“30 seconds, then scrub away loosened residue without touching cutting edges. Hand-wash the Processor Base and Blade Adapter; they must not go in the dishwasher.
Is dry food trapped in the Coffee & Dry Spice Grinder?
  • Unplug the NutriBullet Ultra Plus+ Compact Kitchen System and disengage the Grinder from the Motor Base. Separate the Grinding Cup and Grinder Blade, keeping hands clear of cutting edges.
  • Wash both using a sponge or cloth, soap and water, or place them on the top dishwasher rack without the heat/sanitise cycle. Clean the Motor Base exterior with a damp cloth and check for damage before refitting the attachment.

NutriBullet 600 Mega Pack

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet 600 Mega Pack Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet 600 Mega Pack, then wait until every moving part has stopped.
  2. Remove the cup and extractor blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet 600 Mega Pack Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet 600 Mega Pack extractor blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use the guide-approved hand-washing method to clean the accessible blade surfaces, then rinse and dry the assembly completely.
  • Leave the blade gasket in place. If it becomes loose or damaged, replace the whole blade assembly before refitting it.
Is food dried onto the cup or pitcher?
  • For dried food in the NutriBullet 600 Mega Pack cup, remove the vessel from the base and wash it with soap and water.
  • Use a dish brush or sponge to loosen the remaining deposits and rinse away the residue. A washed rim and fitting area should be clear of stuck food before the blade or lid is refitted.
  • Inspect the cleaned vessel for cracks or damaged fitting tabs; replace a damaged detachable part rather than continuing to use it.

NutriBullet Turbo 1000 Deluxe Set

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Turbo 1000 Deluxe Set Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Turbo 1000 Deluxe Set, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Turbo 1000 Deluxe Set Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Turbo 1000 Deluxe Set Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Turbo 1000 Deluxe Set cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

NutriBullet Turbo Ultimate Pack

Unplug the appliance and wait for all movement to stop before cleaning. Remove surface spills from the NutriBullet Turbo Ultimate Pack Motor Base with a cloth or sponge dampened with warm soapy water. Leave the housing intact.

  1. Switch off and unplug the NutriBullet Turbo Ultimate Pack, then wait until every moving part has stopped.
  2. Remove the cup and Rapid Extractor Blade together. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Turbo Ultimate Pack Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

This video shows how to clean the motor base: unplug it, wipe it inside and out with a damp sponge, use a small brush dipped in warm soapy water, and let it dry before use.

Is food stuck to the detached blade?
  • Inspect the detached NutriBullet Turbo Ultimate Pack Rapid Extractor Blade for food around the cutting area. Keep hands clear of the sharp edges while cleaning.
  • Use a small brush or sponge with soapy water to dislodge residue from the blade, then rinse and dry the assembly completely.
  • Keep the blade intact during cleaning; replace a damaged blade assembly before fitting it to the vessel again.
Is food stuck to the cup or pitcher?
  • Remove the NutriBullet Turbo Ultimate Pack cup from the base before hand-washing it with soap and water.
  • Use a dish brush or sponge to loosen food on accessible surfaces; keep fingers away from blade edges and rinse away all residue.
  • Check that the cleaned cup is sound before refitting it. Replace damaged detachable parts before further use.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: NutriBullet Ultra 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Essentials Set NB9-0807DG user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Mega Pack Black NB9-1107AK user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 600 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1000 / Ultra 1000 Premium user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Select 1200 / 2.0 Select 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Pro+ 1200 / Pro Plus 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 2.0 Pro 1000 NB07100-1008DG user guide (NZ, PDF)

The full steps for this model are in its user guide: NutriBullet 1000 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo 1000 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 1000 Mega Pack / 1000 Series Mega Pack user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 1200 Series / 12 Piece user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 1200 Series / 10 Piece user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 500 Series / 4 Piece user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 700 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Select 1000 / Select 1000 with pitcher user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 600 Essentials Kit user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1200 McLaren / Club Pack user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1200 Premium user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Triple Prep System user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Smart Touch Blender Combo user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Power Core Blender user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Blender Combo 1000 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Power Core Blender Combo user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Portable Blender / Portable Blender McLaren user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Flip Stainless user guide (PDF)

The full steps for this model are in its user guide: Read the NutriBullet Flip Tritan user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Flex Portable / Flex Portable McLaren user guide (PDF)

The full steps for this model are in its user guide: NutriBullet GO user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Juicer 800W user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Cold Press Slow Juicer user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Juicer Pro 1000W user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Cold Press Batch Juicer user guide (PDF)

The full steps for this model are in its user guide: NutriBullet CrispLite Air Fryer 6L user guide (PDF)

The full steps for this model are in its user guide: NutriBullet XXL Digital Air Fryer 7L user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Twin Drawer Air Fryer user guide (PDF)

The full steps for this model are in its user guide: NutriBullet CrispLite Vision Air Fryer 8L user guide (PDF)

The full steps for this model are in its user guide: NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Immersion Blender 800W user guide (PDF)

The full steps for this model are in its user guide: NutriBullet EveryGrain Cooker user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Food Processor user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Chill user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Limitless Food Processor user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Baby user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Baby Steam + Blend user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet To Go 200W user guide (PDF)

The full steps for this model are in its user guide: Read the Magic Bullet Value Pack 200W user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet Blender Combo user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet Mini Juicer user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet Kitchen Express 250W user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet Air Fryer 2.5L user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra Plus+ Compact Kitchen System user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 600 Mega Pack user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo 1000 Deluxe Set user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo Ultimate Pack user guide (PDF)

Related articles

Contact us