• Identify the Tall Cup, stainless-steel Cross Blade and Motor Base; check your pack contents before ordering optional lids or handled cups.
• Inspect the cup and its three locating tabs for cracks, crazing, cloudiness, discolouration, rounded edges or breakage; stop using a damaged cup and replace it.
• Check that the Cross Blade gasket is intact and completely seated before use; do not pull it out. Replace the complete blade if the seal is removed, loose or damaged. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Replace a loose or damaged Cross Blade and inspect it before every use; the guide recommends replacement every six months depending on use, or sooner as needed. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• If operation becomes unusually noisy or vibrates more than before, stop and inspect the consumable cup and blade for wear; replace the affected worn component. Buy a replacement cross blade (Australia) or cross blade (New Zealand).

1. Hand-tighten the Cross Blade onto the cup until sealed, then line up the cup tabs with the base tabs; pressing the cup down starts the motor, and releasing pressure stops it.
2. For lock-on use, press down and gently twist the cup clockwise; twist it anticlockwise to release and wait for movement to stop before lifting it.
3. Remove the cup/blade assembly from the Motor Base before cleaning; wash the cup and other non-motor, non-blade accessories on the top dishwasher rack or by hand with warm soapy water.
4. Hand-wash the Cross Blade, leaving the gasket in place; never place the blade attachment in the dishwasher. Dry both sides completely before storing.
5. Rinse and brush dried food off cups, lids and lip rings before dishwashing; avoid the sanitise cycle because it can warp them.

Next steps

1. Wipe the inside and outside of the unplugged Motor Base with a warm soapy cloth; use a small brush on sticky actuator tabs without removing the rubber or plastic liners. Keep the base out of the dishwasher.
2. Use a flip-top lid when storing blended food instead of leaving the Cross Blade on the cup, and never leave an exposed blade on the Motor Base without a cup attached.
3. Keep all Magic Bullet cups and accessories out of the microwave; never test a new blade by running it empty or without liquid.
4. For extra blade disinfecting after washing, rinse with a 10% vinegar/water solution while leaving the gasket in place.

• Choose Cross Blade MBF50200-BA071CDB for the Blender Combo.
• Use the supplied Tall Cup or an accessory cup specifically listed for Magic Bullet Blender Combo.
• Identify the 450 mL single-serve cup, its To-Go Lid, the 1.5 L pitcher, Pitcher Lid and removable Vented Lid Cap separately when ordering; the Cross Blade is removable from the cup and pitcher.
• Leave the blade seal in place when cleaning; replace the whole blade assembly if its non-removable seal needs replacement.

1. For the cup, tighten the Cross Blade until firmly sealed, turn the cup upside down and twist clockwise onto the Motor Base; the motor must not run with a loose cup/blade assembly.
2. For the pitcher, tighten the blade anticlockwise onto its bottom; turn the blade clockwise to release it, following the arrows underneath the pitcher.
3. Press the Pitcher Lid down until it snaps into place, then press and twist the Vented Lid Cap into its locked position; use both lid pieces during operation.
4. Set the pitcher upright on the base and turn it clockwise until it clicks; if it will not lock, recheck the alignment instead of forcing it.

1. Return the control to HOME, wait until the blade has stopped, unplug, then detach the cup or pitcher from the Motor Base.
2. For the sealed cup, turn it upright with the Cross Blade on top, untwist the blade, then transfer the ingredients.
3. For the pitcher, lift the lid tab and remove the lid, transfer the ingredients, then twist off the Cross Blade following the direction arrows underneath the pitcher.
4. Wash the cup, pitcher, blade and accessories with soap and water or in the top rack of the dishwasher; do not use the sanitise cycle.
5. Wipe the Motor Base with a damp sponge or cloth and clean the actuator with a small dry brush. Never remove base pieces.
6. Store the components together where they cannot be damaged or cause injury, with no blade exposed.

• Identify the Juice Bowl, Juice Bowl Cover with 5 cm Feed Chute, Food Pusher, stainless-steel Sieve, Pulp Bin, 470 mL Juice Cup and lid, silicone spout cap and sieve cleaning brush; request the named piece against MBJ07110K.

1. Place the Juice Bowl on the unplugged Motor Base and rotate it until the keyed shape seats; the bowl’s open side must face the rear.
2. Hold the Sieve by its upper rim, align it with the motor drive coupling and push down until it clicks; keep fingers off the sharp teeth.
3. Fit the cover with the Feed Chute above the Sieve and pulp chute at the rear; raise both Locking Arms to grip the cover edge and snap their lower sections closed. Both arms must stand vertically and lock.
4. Tilt the Pulp Bin into place under the cover’s rear edge until it snaps, then gently push the bin base inward to lock it.
5. Slide the Food Pusher into the Feed Chute; use that pusher rather than fingers or a kitchen utensil to feed ingredients.
6. Point the silicone spout cap down for juicing; fit the Juice Cup Lid, open its latch and tip the cup slightly so the spout sits just inside the lid opening.
7. To remove the cup, tip it forward and slide it away, then rotate the spout cap upward to catch residual drips.
8. For disassembly, release both Locking Arms, tilt out the Pulp Bin, remove the cover and lift the bowl with the Sieve still inside; lift the Sieve vertically by its edge over the sink.

1. Empty and rinse all non-motor parts after use; use the supplied brush to clean the Sieve under running water, brushing the outside first and then the inside.
2. If pulp has dried in the Sieve, soak it in hot water for 30 minutes, then brush the holes clear; clean after every use to prevent mineral and pulp build-up from reducing extraction.
3. Hand-wash removable parts with warm soapy water or use the dishwasher without the heat sanitation cycle; periodically clean the Juice Bowl with water and vinegar.
4. Wipe the Motor Base with a clean damp cloth.NEVER submerge the motor base in water or any other liquid.
5. Store the Juice Cup upright with its lid sealed, latch closed and nothing on the lid; unplug the juicer, wrap the cord beneath the base and keep the assembled parts together in a cool, dry safe place.
6. Replace the Sieve if it is dull or becomes less efficient after proper cleaning; choose genuine Mini Juicer parts.

• Use only the cup and Cross Blade assembly specifically designed for Magic Bullet Kitchen Express 250W.
• Identify the 830 mL Work Bowl, Bowl Lid with Feed Chute, Food Pusher, Chopping Blade and reversible Slice/Shred Disc as the food-processor set.
• Identify the two 530 mL Tall Cups, To-Go Lid and stainless-steel Cross Blade as the blending set.

1. For chopping, lower the Chopping Blade onto the bowl shaft, then fit the Bowl Lid and turn it clockwise to lock.
2. For slicing or shredding, hold the disc by its two larger finger holes and lower it onto the bowl shaft with the required cutting side facing up.
3. Turn the filled Work Bowl clockwise onto the Motor Base and check that both bowl and lid are locked before switching on; the motor will not run if either is loose.
4. Use the Food Pusher to guide cut-to-fit ingredients down the Feed Chute; do not overload the chute or force food through it.
5. For blending, screw the Cross Blade onto the cup until sealed, invert it and turn clockwise onto the base; use the cup’s MAX mark to limit the load.
6. After stopping, turn the bowl or cup anticlockwise to unlock; remove a Chopping Blade before pouring food out of the bowl.

1. Empty the Work Bowl, separate all removable pieces and keep the bowl and cup/blade assembly off the Motor Base while cleaning.
2. Hand-wash removable parts with warm soapy water and rinse, or use the dishwasher top rack without the sanitise cycle; lift the disc by its two finger holes.
3. Wipe the Motor Base with a damp cloth and use a small brush to clear dried food from its actuator system. Never remove base components.
4. Keep all components together in a safe place where the sharp attachments cannot cause harm or become damaged.

• Identify the removable Fry Pot and Crisping Tray; the temperature dial and timer are on the Base. Request the named replacement for Magic Bullet Air Fryer 2.5L product code MBA07100.

1. Place the Crisping Tray at the bottom of the Fry Pot; it must sit securely and level with the pot bottom. Keep fingers away from its sharp edges.
2. Hold the pot handle and push the Fry Pot into the Base until it clicks; the outside of the pot must sit flush with the Base, with no part sticking out.
3. If the pot will not seat, remove excess food and leave about 50 mm clear at the top, then refit it; the air fryer will not operate with the Fry Pot installed incorrectly.

1. Turn the timer to 0 and check the orange light is off, unplug and let the heating element cool completely before removing the Fry Pot.
2. Remove the Fry Pot from the Base, lift the Crisping Tray by its centre handle and clear food scraps from both pieces.
3. Rinse the Fry Pot and Crisping Tray with hot soapy water after every use so residue does not bake on; check both are clean before refitting.
4. Wipe only the Base exterior with a clean damp cloth.NEVER submerge the main unit in water. Store all parts together somewhere safe from damage.