1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning. These steps cover Ultra 1000 Premium product code NB07500-1008. For another Ultra 1000 product code, follow the cleaning instructions supplied with that exact pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Detach the cup and blade assembly or pitcher from the motor base, then separate the components for cleaning.
3. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.
6. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.

Next steps

1. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
2. Wash the pitcher. Rinse and briefly brush the pitcher before putting it in the dishwasher, without the sanitise cycle; alternatively hand-wash it with soap and water and remove stuck food with a dish brush or sponge.
3. Clean the tamper. Always hand-wash the tamper with soap and water; scrub stuck-on ingredients with a dish brush or sponge.
4. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
5. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
6. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, invert the sealed cup and blade onto the motor base, then gently push and twist to start; turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Switch off and unplug the motor base Wait until every moving part has stopped, then remove the cup and easy-twist extractor-blade assembly before cleaning.
2. Wash the cups and to-go lids on the dishwasher top rack, without a sanitise cycle
3. Hand-wash the easy-twist extractor blade with soap and water Do not remove any blade components.
4. Wipe the unplugged motor base with a cloth dampened with warm soapy water Use a small brush on the actuator area if needed. NEVER submerge the motor base in water.
5. Dry the easy-twist extractor blade completely after every use. Check its underside for cracking or breakage and replace a damaged blade immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. These instructions apply to NutriBullet 1000 Series N10-0807DG. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the sealed cup and blade assembly on the motor base and blend for about 20–30 seconds to loosen dried food.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning. These steps cover Turbo 1000 product code NBT07400-1006AK. For NBT07400-1004AW or NBT07400-1006AW, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Take the blender apart for cleaning. These steps cover the black 1000 Series Mega Pack, product code N10-1107AK. For another pack code, match the cleaning method to the guide supplied with it; use the Milling Blade steps only when that blade is included. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 12 Piece pack, product code N12-1207C, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Use these 1200 Series care instructions only if they match your pack’s guide. For the 10 Piece pack, product code N12-1007, check the user guide that came with it for the correct start control and accessory instructions. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect the assembled blender to power and run the sealed cup and extractor blade assembly on the motor base for about 20–30 seconds, using the start control shown in the guide supplied with your 1200 Series pack.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare to clean. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and gently turn clockwise to start the automatic cycle; turn the cup anticlockwise to stop after 20–30 seconds.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.

Next steps

1. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.
2. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
3. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
4. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
5. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare for cleaning.

   Unplug the motor base and wait for all moving parts to stop before removing or separating the cup and blade. Let a warm sealed cup cool before carefully opening it away from your body.

2. Wash the cup and lid.

   Cups and To-Go Lids can be washed by hand in warm soapy water or placed on the dishwasher’s top rack. Do not use the sanitise cycle; it can warp the plastic.

3. Hand-wash the extractor blade.

   Hand-wash the extractor blade with warm soapy water and rinse. Keep it out of the dishwasher, leave its gasket in place, and dry both sides completely. A loose or damaged gasket requires a complete replacement extractor blade.

4. Wipe the motor base.

   Wipe the unplugged base with a sponge or cloth dampened with warm soapy water. Use a small brush if needed on accessible white actuator tabs. NEVER submerge the motor base in water. Do not remove the motor base's rubber or plastic liners. If liquid has entered the electrical base, leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Take the blender apart for cleaning. Unplug the motor base and wait until all moving parts have stopped before touching or removing any parts.
2. Remove the cup and blade. Lift the cup and extractor blade assembly off the motor base, then separate the cup from the extractor blade for washing.
3. Loosen dried food inside the cup. Fill the cup about two-thirds full with room-temperature water at 21°C or cooler, then screw the extractor blade on tightly.
4. Reconnect power, place the inverted sealed cup and blade assembly on the motor base, then gently push down and twist; run for about 20–30 seconds, then gently push and turn the cup anticlockwise to stop.
5. Finish removing the residue. Stop the motor, unplug the base and remove the assembly after the blades stop; open the cup, lightly scrub away the loosened food and rinse.

Next steps

1. Rinse the cups and To-Go Lids and briefly brush off dried food with a dish brush before loading them.
2. Wash the cups and lids. Wash the cups, To-Go Lids and other removable pieces, except the motor base and extractor blade, in warm soapy water and rinse; alternatively place these washable pieces on the dishwasher top rack.
3. Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
4. Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean. NEVER submerge the motor base in water.
5. Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.

This video shows the easiest way to keep your cup and blade clean: rinse them right after use, then towel-dry them or leave them on a drying rack.

1. Prepare to clean. These steps cover the cup and blade of Select 1000 product code NB07200-1007DG. For the Select 1000 with pitcher, product code NB07200-1006DG, use its supplied pitcher instructions. Power off, unplug the motor base and wait until every moving part has stopped before taking the blender apart.
2. Detach the cup and blade assembly from the motor base, then separate the components for cleaning.
3. Fill the cup to its MAX line with room-temperature water at 21°C or cooler and add 1–2 drops of dish soap; tightly screw on the easy-twist extractor blade.
4. Reconnect power and press POWER, lock the sealed cup and blade assembly clockwise onto the motor base, select LOW or HIGH and blend for 20–30 seconds; press the selected speed or POWER to stop.
5. Finish the clean. Stop, unplug and wait for the blade to stop before removing the assembly; scrub the loosened debris away with soap and water.

Next steps

1. Wash cups and To-Go Lids. Rinse the cups and To-Go Lids, briefly scrub any remaining debris with a dish brush, then put them on the dishwasher top rack.
2. Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
3. Wipe the motor base. Use a sponge or dish cloth dampened with warm soapy water to wipe the unplugged motor base until clean; wipe external leakage residue with a damp sponge and warm water.
4. Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place. NEVER submerge the motor base in water.
5. Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Prepare for cleaning. These steps cover Ultra 1200 McLaren product code NB07500-1206GO-MC. For Club Pack product code NB07500-1214S, follow the guide supplied with that pack. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Start cleaning. Power off and unplug the Motor Base, wait until the motor and all attachments stop, then detach the Cup, Blending Pitcher or Work Bowl.
2. Choose the vessel that needs a rinse blend. For the Cup, fill to the MAX line with room-temperature water and add one or two drops of dish soap; twist the Extractor Blade on tightly, mount the assembly on the Motor Base, plug in and blend for 20–30 seconds. For the Blending Pitcher, fill halfway with water and add one or two drops of dish soap; fit the Pitcher Lid, press the Lid Cap down firmly and twist it until locked, lock the Pitcher onto the Motor Base, plug in and blend for 20–30 seconds. Use the matching method for the vessel you are cleaning.
3. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; continue with the component washing steps below.
4. Clean the Extractor Blade. Clean the Extractor Blade immediately after use with a small brush or sponge dampened with soapy water, keeping fingers away from the cutting edges.
5. Clean the base. Wipe the Motor Base with a warm sponge or dishcloth dampened with soapy water; use a small brush to clean its actuator system, then wipe dry with a clean cloth. NEVER submerge the motor base in water or cleaning liquid.
6. Choose a safe dishwasher cycle. Do not use the dishwasher heat or sanitise cycle for any part or accessory; the heat can warp parts.

Next steps

1. Rinse or scrub debris from the Blade Adapter, Blade Attachments, Cups, Food Pusher and To-Go Lids before washing them in the dishwasher.
2. Wash the pitcher. Wash the Blending Pitcher and Pitcher Lid in the dishwasher, or hand-wash with soap and water without touching the sharp blades.
3. Wash the tamper. Hand-wash the Tamper with soap and water.
4. Wash the processor bowl. Remove all Blade Attachments, Discs and the Blade Adapter from the Work Bowl before washing the Work Bowl and Work Bowl Lid in the dishwasher or by hand with soap and water.
5. Store the system. Store NutriBullet Triple Prep System upright with nothing on top, with accessories safely covered. In the Work Bowl, fit the Blade Adapter onto the central shaft, then the Chopping Blade, Dough Blade and Slice/Shred Disc, and fit the Lid. Never store exposed Blades or Discs.

1. Take the blender apart for washing. Match the product code on your NutriBullet Blender Combo 1200 to NBF07500-1210DG before following these steps; check the guide supplied with a different Blender Combo 1200 pack. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Loosen dried ingredients. Fill the Cup or Pitcher to its MAX line with room-temperature water at 21°C or below, and add one or two drops of dish soap.
3. Run the cleaning blend. For a Cup, twist on the Easy-Twist Extractor Blade and mount the assembly on the Motor Base; for the Pitcher, fit the Lid and mount it on the base. Plug in and blend for 20–30 seconds.
4. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; continue with the component washing steps below.
5. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
6. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.

Next steps

1. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
2. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
3. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.
4. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
5. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.

1. Which SmartSense parts are dishwasher-safe? These washing and control instructions are for NutriBullet SmartSense Blender NBF07600. Wash the SmartSense Blender Pitcher in the dishwasher; keep the Tamper and Motor Base out of the dishwasher.
2. Wash the tamper and wipe the base. Hand-wash the Tamper with soap and water. Wipe the Motor Base with a damp cloth. NEVER submerge the motor base in water.

1. Which SmartSense parts are dishwasher-safe? These washing and control instructions are for NutriBullet SmartSense Blender Combo NBF07700-1507. Wash the SmartSense Blender Combo Pitcher in the dishwasher; keep the Tamper and Motor Base out of the dishwasher.
2. Wash the tamper and wipe the base. Hand-wash the Tamper with soap and water. Wipe the Motor Base with a damp cloth. NEVER submerge the motor base in water.

1. Take the blender apart for washing. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
3. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.
4. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
5. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender.
6. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.
7. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
8. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.

1. Begin cleaning. Turn off and unplug the blender; wait until all parts stop, then remove the Pitcher from the Motor Base.
2. Clean the base. Wipe the outside of the unplugged Motor Base with a clean cloth. NEVER submerge the motor base in water. Do not take the motor base apart.
3. Clear the actuator area. Use a small brush to clear residue around the actuator system while the Motor Base is unplugged.
4. Wash the pitcher. Rinse and briefly scrub the Pitcher with a dish brush before dishwasher washing, or hand-wash with soap and water. Use a brush or sponge on stuck food and keep clear of the sharp blades.
5. Wash the lid and cap. Before first use, rinse detachable parts and hand-wash with warm soapy water or wash in the dishwasher. Keep the Motor Base out of the dishwasher.

1. Take the blender apart for washing. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Loosen dried ingredients. Fill the Cup or Pitcher to its MAX line with room-temperature water at 21°C or below, and add one or two drops of dish soap.
3. Run the cleaning blend. For a Cup, twist on the Easy-Twist Extractor Blade and mount the assembly on the Motor Base; for the Pitcher, fit the Lid and mount it on the base. Plug in and blend for 20–30 seconds.
4. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; continue with the component washing steps below.
5. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
6. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.

Next steps

1. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
2. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
3. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.
4. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
5. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.

1. Begin cleaning. Turn off and unplug the blender; wait until all parts stop, then remove the Pitcher or Cup from the Motor Base.
2. Fill the vessel for a cleaning blend. Fill the Cup or Pitcher to its liquid MAX line with room-temperature water at 21°C, then add one or two drops of dish soap.
3. Run the cleaning blend for that vessel. For a Cup, twist the Extractor Blade tightly onto it and mount the assembly on the Motor Base. For a Pitcher, secure the Pitcher Lid with its Vented Lid Cap inserted and lock the Pitcher onto the Motor Base. Plug in and blend on LOW for 20–30 seconds.
4. Stop and detach the vessel. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; then continue with the washing steps below.
5. Clean the base. Wipe the outside of the unplugged Motor Base with a clean cloth. NEVER submerge the motor base in water. Do not take the motor base apart.

Next steps

1. Clear the actuator area. Use a small brush to clear residue around the actuator system while the Motor Base is unplugged.
2. Wash the pitcher. Rinse and briefly scrub the Pitcher with a dish brush before dishwasher washing, or hand-wash with soap and water. Use a brush or sponge on stuck food and keep clear of the sharp blades.
3. Wash the cups and lids. Rinse and briefly scrub Cups and To-Go Lids with a dish brush before putting them on the dishwasher top rack; do not use the sanitise cycle.
4. Wash the detachable blade and other accessories. Before first use, rinse detachable parts and wash them with warm soapy water; the first-use instructions also permit dishwasher washing for parts other than the Motor Base, without heat or sanitise cycles.
5. Store the clean pitcher. Store the Pitcher upright with its Lid secured and nothing on top; keep remaining parts somewhere safe from damage.

1. Find the full product code on the NutriBullet Power Core Plus appliance label. NEVER submerge the motor base in water.
2. Use the NutriBullet Power Core Plus user guide supplied with that product code for washing each part and checking dishwasher permission

1. Prepare for washing. Turn NutriBullet Portable Blender off after use, disconnect the charger and wait for the blades to stop before removing the Cup or cleaning.
2. Loosen residue with a rinse blend. For stuck residue, add cold water and a drop of soap to the Cup without passing MAX, fit the Lid and lock its latch; press Power to wake, wait about one second, then press again for one 20-second cycle. Turn off and wait for the blades to stop before washing.
3. Wash the cup and lid. Hand-wash the Cup and Lid in warm soapy water and rinse clean, or put them on the dishwasher top rack without the heat or sanitise cycle.
4. Clean the fixed blades. Gently rinse only the blade assembly and wipe it with a damp sponge or cloth; keep your fingers away from the sharp blades.
5. Protect the motor base. Do not place the motor base under running water or put the motor base in the dishwasher.
6. Wipe and dry the motor base. Gently wipe and dry the Motor Base with a clean cloth. NEVER submerge the motor base in water or cleaning liquid.
7. Store the blender. Store upright in a safe place with the Cup attached to cover the blades; do not stack anything on top.

1. Prepare to clean Flip. Disconnect the charger and leave NutriBullet Flip Stainless undisturbed for 90 seconds so it shuts down completely; check that the blades have stopped before taking parts apart.
2. Prepare a cleaning blend. Rinse out the Blending Cup with fresh water, add a drop of dish soap and fill the cup halfway with water.
3. Start the cleaning cycle. Secure the Motor Base, Blade, and Lid on the Cup with the Flip-Top Lid closed. Wake the blender with Power, then press Power again to start the 30-second cycle; flip and shake the blender to agitate the water.
4. Rinse afterwards. When the cycle ends, open the Flip-Top Lid over the sip hole and empty the soapy water; repeat one cycle with fresh water only, without soap.
5. Switch from the cleaning blend to hand washing. After the final rinse cycle, disconnect the charger and leave Flip undisturbed for 90 seconds to shut down completely; check that the blades have stopped before hand washing or removing parts.
6. Clean the Blending Cup. Wash the Blending Cup with soap and water.

Next steps

1. Rinse the blades. Point the blade downward at an angle and carefully rinse only the blade area, keeping a thumb or finger over the USB-C port. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire Motor Base, Blade, and Lid assembly.
2. Clean the drinking spout. With the blade facing upwards, carefully rinse the sip hole under a gentle flow of warm water while covering the USB-C port with a thumb or finger.
3. Reach narrow openings. Use the supplied Cleaning Brush for the straw, under the blades, the sip hole and the vent hole.
4. Dry Flip fully. Wipe the Motor Base, Blade, and Lid and pat the USB-C port dry with a clean cloth. Stand the assembly upright with the Flip-Top Lid open and allow it to dry fully in a sunny area before charging; avoid excessive heat and keep within the guide’s recommended 10–40°C storage and charging range.
5. Store Flip. Store in a dry, temperature-controlled place with the Cup or Blade Cover attached over the blades; put nothing on top.

1. Prepare to clean Flip. Disconnect the charger and leave NutriBullet Flip Tritan undisturbed for 90 seconds so it shuts down completely; check that the blades have stopped before taking parts apart.
2. Prepare a cleaning blend. Rinse out the Blending Cup with fresh water, add a drop of dish soap and fill the cup halfway with water.
3. Start the cleaning cycle. Secure the Motor Base, Blade, and Lid on the Cup with the Flip-Top Lid closed. Wake the blender with Power, then press Power again to start the 30-second cycle; flip and shake the blender to agitate the water.
4. Rinse afterwards. When the cycle ends, open the Flip-Top Lid over the sip hole and empty the soapy water; repeat one cycle with fresh water only, without soap.
5. Switch from the cleaning blend to hand washing. After the final rinse cycle, disconnect the charger and leave Flip undisturbed for 90 seconds to shut down completely; check that the blades have stopped before hand washing or removing parts.
6. Clean the Blending Cup. Wash the Blending Cup with soap and water.

Next steps

1. Rinse the blades. Point the blade downward at an angle and carefully rinse only the blade area, keeping a thumb or finger over the USB-C port. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire Motor Base, Blade, and Lid assembly.
2. Clean the drinking spout. With the blade facing upwards, carefully rinse the sip hole under a gentle flow of warm water while covering the USB-C port with a thumb or finger.
3. Reach narrow openings. Use the supplied Cleaning Brush for the straw, under the blades, the sip hole and the vent hole.
4. Dry Flip fully. Wipe the Motor Base, Blade, and Lid and pat the USB-C port dry with a clean cloth. Stand the assembly upright with the Flip-Top Lid open and allow it to dry fully in a sunny area before charging; avoid excessive heat and keep within the guide’s recommended 10–40°C storage and charging range.
5. Store Flip. Store in a dry, temperature-controlled place with the Cup or Blade Cover attached over the blades; put nothing on top.

1. Take Flex apart. Use these steps for NutriBullet Flex Portable NBPB07222 and Flex Portable McLaren Papaya NBPB07222PA-MC. Check the remaining charge on the LED Battery Bar, then turn the blender off and disconnect the charger. Gently twist the Cup and Blade Block off the Motor Base, holding the Cup and base without pushing down or gripping the Sip Lid. Twist the Blade Block clockwise to remove it, keeping clear of the blades; close the Sip Cap before twisting the Sip Lid with Carry Loop anticlockwise.
2. Wash the detachable parts. Hand-wash the Blade Block with warm soapy water and rinse clean, taking care around its sharp blades. Wash the Blending Cup and Sip Lid with Carry Loop with warm soapy water, or put those two parts on the dishwasher top rack without a heat or sanitise cycle.
3. Clean the motor base. Wipe food from the Motor Base with a damp cloth. Keep its Silicone Charge Port Cover in place. NEVER submerge the motor base in water. Never put the base in the dishwasher or run the motor base under water.
4. Dry before reassembly. Dry the Blade Block completely before attaching it to the Cup. Fully dry the Sip Lid before blending or storage; air-dry with the Sip Cap open to avoid trapped moisture around the seal.
5. Store Flex. Store upright with the Blade Block secured to the Blending Cup and the Sip Lid attached so the blades stay covered; do not stack objects on top.

1. Prepare GO for cleaning. Turn NutriBullet GO off and check that no light is on; wait for the motor and blades to stop before separating the cup.
2. Wash the cup and lid. Place the Cup and Lid on the dishwasher top rack, or hand-wash them with warm soapy water and rinse.
3. Clean the blades. Gently rinse the blade assembly and carefully wipe it with a damp sponge or cloth, without touching the sharp edges.
4. Store GO. Keep all parts together in a safe place; screw the Blade Cover onto the Motor Base when it is not in use.

1. Stop and prepare for cleaning. Match the original Juicer 800W product code NBJ07100; follow the spout and control instructions for that code. Turn the juicer off, unplug it and wait until the motor and Sieve have completely stopped.
2. Remove the juice pitcher. For NBJ07100, remove the Juice Pitcher from under the spout and lower the No-Drip Spout cover over the opening to prevent drips.
3. Unlock the bowl. Pull the Locking Handle backwards out of the ears on both sides of the Basin Cover, then lower the handle.
4. Take the juicing parts to the sink. Lift the Pulp Basin from the Motor Base with its Basin Cover and Sieve still in place; take that assembly to the sink.
5. Remove the pusher and cover. Lift the Food Pusher out of the feed chute; lift the Basin Cover vertically off and scrape pulp from its inside with the Cleaning Brush’s flat end.
6. Lift out the sieve. Gently lift the Sieve straight up from the centre of the Pulp Basin without touching its sharp blade teeth; clean it immediately.

Next steps

1. Empty the pulp. Use the flat end of the Cleaning Brush to scrape pulp from the Pulp Basin, then empty the basin and rinse the detached parts under running water.
2. Clean the sieve holes. Scrub the Sieve under running water with the Cleaning Brush after every use; avoid its sharp teeth and remove residue from blocked holes.
3. Hand-wash the Food Pusher with warm soapy water. Keep the Motor Base out of the dishwasher
4. For NBJ07100, wash the detachable juicing parts other than the Food Pusher in the dishwasher, or hand-wash them in warm soapy water Keep the Motor Base out and do not use the sterilise cycle.
5. Clean the motor base. Wipe the Motor Base with a clean damp cloth. NEVER submerge the motor base in water or another liquid.

1. Prepare to take the slow juicer apart. Turn OFF, let the juicer cool completely, unplug and wait until the motor, grinding assembly and all moving parts stop.
2. Remove the containers. Take the Juice Container from under the juice spout and close the spout cover to prevent drips; remove the Pulp Container.
3. Remove the cover and auger. Turn the Juice Bowl Cover anticlockwise to unlock and lift it off; remove the Auger from the bowl.
4. Separate the screen and brush. Lift the Juice Bowl from the base, remove the Rotating Bowl Brush and Juicing Screen together, then slide the brush down to separate it from the screen. Lift out the Food Pusher.
5. Empty the Juice and Pulp Containers, saving or discarding their contents, before washing.
6. Rinse the removable parts. Rinse the Juice Bowl Cover, Food Pusher, Auger, Juicing Screen, Rotating Bowl Brush, Juice Bowl and both containers under running water; do not use a metal sponge.

Next steps

1. Wash detachable parts with warm soapy water or in the dishwasher, except the Auger, which must be hand-washed with warm soapy water and a soft cloth. Keep the Motor Base out of the dishwasher
2. Clear the juicing screen. Use the small Cleaning Brush under running water to clean the Juicing Screen after every use; clear the holes without touching its sharp edges.
3. Clear the pulp spout. Pull the pulp plug out of the pulp spout; use the narrow end of the Cleaning Brush inside the spout and run water through the bowl and spout until remaining pulp is removed.
4. Refit the pulp plug. Before reassembly, check underneath the Juice Bowl and seat the pulp plug properly in the pulp spout.
5. Clean the motor base. Wipe the outside of the Motor Base with a clean damp cloth. NEVER submerge the motor base in water or any other liquid.
6. Dry and store the slow juicer. Dry all parts thoroughly, reassemble and store in a safe, dry place; the Juice Container fits inside the Pulp Container. When moving the juicer, hold the base rather than the Juice Bowl or Cover.

1. Stop and prepare for cleaning. Turn the juicer off, unplug it and wait until the motor and Sieve have completely stopped.
2. Remove the juice pitcher. Remove the Juice Pitcher from under the spout and lower the No-Drip Spout cover over the opening to prevent drips.
3. Unlock the bowl. Pull the Locking Handle backwards out of the ears on both sides of the Basin Cover, then lower the handle.
4. Take the juicing parts to the sink. Lift the Pulp Basin from the Motor Base with its Basin Cover and Sieve still in place; take that assembly to the sink.
5. Remove the pusher and cover. Lift the Food Pusher out of the feed chute; lift the Basin Cover vertically off and scrape pulp from its inside with the Cleaning Brush’s flat end.
6. Lift out the sieve. Gently lift the Sieve straight up from the centre of the Pulp Basin without touching its sharp blade teeth; clean it immediately.

Next steps

1. Empty the pulp. Use the flat end of the Cleaning Brush to scrape pulp from the Pulp Basin, then empty the basin and rinse the detached parts under running water.
2. Clean the sieve holes. Scrub the Sieve under running water with the Cleaning Brush after every use; avoid its sharp teeth and remove residue from blocked holes.
3. Hand-wash the Food Pusher with warm soapy water. Keep the Motor Base out of the dishwasher
4. The remaining detachable juicing parts are dishwasher-safe; they can also be hand-washed in warm soapy water. Do not use the dishwasher sterilise cycle.
5. Clean the motor base. Wipe the Motor Base with a clean damp cloth. NEVER submerge the motor base in water or another liquid.
6. Wash the Glass Storage Bottles and their lids, and the Freezer Trays and their lids, in the dishwasher.

1. Prepare to clean the Batch Juicer. Turn the Dial to OFF, unplug and wait for the Auger and motor to stop before opening or removing anything.
2. Remove the hopper. Open the Lid, hold the Hopper handle and turn it anticlockwise until the arrows no longer align; lift the Hopper off.
3. Remove the auger and bowl. Pull the Auger straight upwards out of the Juicing Bowl, then lift the Juicing Bowl off the Motor Base.
4. Rinse out pulp. Empty the Hopper and Juicing Bowl, then rinse the detached parts under running water.
5. Scrub the Auger with the Cleaning Brush under running water; clean the Auger, Hopper and Juicing Bowl every time to prevent residue buildup.

Next steps

1. Clean under the bowl. Clean beneath the Juicing Bowl, including the Silicone Cover, Spouts and Spout Cover.
2. Reseat the silicone cover. After washing, push the Silicone Cover firmly back into place until it is fully inserted and sits flush.
3. All components except the Motor Base are dishwasher-safe, or can be hand-washed in warm soapy water. Avoid the sterilise cycle, metal sponges and abrasive pads.
4. Clean the motor base. Wipe the Motor Base with a clean damp cloth. NEVER submerge the motor base in water or any other liquid.
5. Store the Batch Juicer. Keep the parts together in a safe place where sharp pieces cannot cause harm; do not place anything on top of the container lid.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Air Fryer 6L; allow it to cool down thoroughly before removing or cleaning parts.
2. Remove the Cooking Basket and 3-in-1 Tray Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and 3-in-1 Tray or any oven cleaner; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Air Fryer 6L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Air Fryer 6L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet XXL Digital Air Fryer 7L; allow it to cool down thoroughly before removing or cleaning parts.
2. Remove the Cooking Basket and Crisping Tray Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and Crisping Tray; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet XXL Digital Air Fryer 7L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid.
6. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet XXL Digital Air Fryer 7L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet Twin Drawer Air Fryer; allow it to cool down thoroughly before removing or cleaning parts.
2. Remove the Cooking Drawers and Crisping Trays Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Drawers and Crisping Trays; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet Twin Drawer Air Fryer base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid.
6. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet Twin Drawer Air Fryer and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Vision Air Fryer 8L; allow it to cool down thoroughly before removing or cleaning parts.
2. Remove the Cooking Basket and 3-in-1 Tray Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and 3-in-1 Tray or any oven cleaner; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Vision Air Fryer 8L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Vision Air Fryer 8L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L; allow it to cool down thoroughly before removing or cleaning parts.
2. Remove the Cooking Basket, Crisping Tray and Wire Rack. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket, Crisping Tray and Wire Rack; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L and store it in a safe, dry location.

1. Take the blender apart. Unplug the NutriBullet Immersion Blender 800W and wait until the motor, blade or whisk has completely stopped. Lift the stopped blending arm or whisk out of its mixing vessel, then detach the motor body from the blending arm, whisk or chopping bowl. Separate the whisk from its holder, or the S-blade and lid from the chopping bowl; leave the blending arm as one piece. Empty the mixing vessel or chopping bowl.
2. Wash the chopping bowl, whisk, blending cup and chopping blade with warm, soapy water, or place those parts in the dishwasher.
3. Clean the geared attachments. Hand-wash the whisk holder, chopping bowl lid and blending arm with warm, soapy water. Do not soak these three parts or put them in the dishwasher, because water can damage the internal gears.
4. Avoid metal sponges. Do not use a metal sponge to clean any parts; it can scratch or damage them.
5. Clear the blade and whisk. Clean the blade and whisk after every use, handling the sharp blade carefully; remove all traces of food so residue does not build up and reduce blending performance.
6. Clean the motor unit. Wipe the motor unit with a damp cloth only. NEVER submerge the main unit in water or another liquid.
7. Dry and store attachments. Let all parts dry thoroughly, then store the NutriBullet Immersion Blender 800W and attachments in a safe, dry place where they cannot be damaged or cause harm.

1. Prepare the cooker for cleaning. Remove cooked food from the Cooking Pot or Steaming Basket for serving or storage, and discard leftover scraps. Turn off and unplug the NutriBullet EveryGrain Cooker and let it cool completely before cleaning the heating plate.
2. Remove stuck-on food. Soak the Cooking Pot with water before cleaning if food sticks. For hard residue, apply dishwashing liquid directly to it, leave it for a few minutes, then soak the area in water.
3. Wash the Steaming Basket, Spatula and Measuring Scoop in warm, soapy water, or put these accessories in the dishwasher.
4. Protect the Cooking Pot. Always hand-wash the Cooking Pot with warm, soapy water to protect its non-stick coating. Do not put the Cooking Pot in the dishwasher.
5. Clean the heating plate. After the heating plate is completely cool, wipe it with a clean, damp cloth. Clean the Cooking Pot, used Steaming Basket and heating plate after every use to prevent buildup.

Next steps

1. Clean the lid and water collection parts. After every use, wipe the Sealing Panel and Condensation Collector thoroughly with a damp cloth or sponge and warm, soapy water. Remove the Steam Vent plug and rinse it in warm water; wipe inside the Steam Vent with a damp cloth.
2. Avoid steel wool. Do not use steel wool pads or balls on the Cooking Pot, Sealing Panel or any other cooker part.
3. Clean the Cooker Base. Wipe the Cooker Base with a damp cloth only. NEVER submerge the main unit in water or another liquid.
4. Store the cooker. Once the NutriBullet EveryGrain Cooker is off, unplugged and at room temperature, store it upright in a cool, dry place with its accessories and power cord.

1. Prepare the processor for cleaning. Turn off and unplug the NutriBullet Food Processor, then detach the blades and other attachments from the Motor Base before cleaning.
2. Wash the Blade Adaptor, Chopping Blade, Dough Blade, Slice/Shred Discs, Spiralizer Disc, Work Bowl, Work Bowl Lid and Dual-Size Food Pusher by hand in warm, soapy water or on the dishwasher top rack.
3. Handle the blades. Handle each sharp blade attachment carefully while removing and cleaning it.
4. Avoid damaging cycles and scrubbers. Do not use a sanitise cycle, steel wool pads or balls, or other hard materials that can warp or scratch the Work Bowl, lid and other parts.
5. Clean the Motor Base. Keep the Motor Base unplugged. Wipe it with a sponge or dishcloth dampened with warm, soapy water; use a small brush on the actuator system area if food remains. Wipe leakage residue with a damp sponge and warm water. NEVER submerge the motor base in water. Never remove pieces from the base.
6. Store the blade attachments. With the processor off and unplugged, fit the Blade Adaptor over the centre shaft. Lower the Chopping Blade onto the shaft, then the Dough Blade above it. Place the disc attachments on the adaptor above the blades, in their lower storage position; the disc and adaptor lines should not align.
7. Choose a storage arrangement. Store either both Slice/Shred Discs with the Chopping Blade and Dough Blade, or one Slice/Shred Disc and the Spiralizer Disc with those blades. Put the Spiralizer Disc in last, aligning its notches with the upper tabs and turning its FRONT marking towards the front.
8. Close the stored processor. Lock the Work Bowl Lid onto the bowl with the Dual-Size Pusher nested in the Feed Chute, then wrap the power cord under the Motor Base.

1. Prepare Chill for washing. Unplug the NutriBullet Chill and wait until all parts stop moving before handling them. Handle the sharp blade by its shaft, keeping fingers away from its edge.
2. Separate and wash the detachable parts. Remove the Blade from the Blade Block before placing the Pint Cup, lid, Blade, Blade Block and Shaft on the dishwasher top rack. These parts can also be washed by hand with warm, soapy water.
3. Hand-wash the Blade Block. Use a sponge and dish soap to gently clean the circular opening in the Blade Block and around the Blade Shaft.
4. Clean the Motor Base. Wipe the Motor Base with a damp sponge or cloth and mild, soapy water. Use a cleaning brush around the top where the Pint Cup attaches if needed. Keep liquid away from the drive shaft and centre hole. NEVER submerge the motor base in water. Do not put the motor base in the dishwasher.
5. Store the blade safely. Make sure all parts are clean and dry. Store the NutriBullet Chill unplugged, with the Blade Cover fitted to the blade or the blade attached to the Pint Cup. Never leave an exposed Blade Block on the Motor Base.

1. Prepare the processor for cleaning. Turn off and unplug the NutriBullet Limitless Food Processor before detaching blades and accessories from the Motor Base.
2. Hand-wash the Blade Adaptor, Chopping Blade, Reversible Slice/Shred Disc, Work Bowl, lid, Food Pusher, Endless Chute and Slinger Disc with warm, soapy water, or place them on the top dishwasher rack. Keep the dishwasher temperature at or below 82°C.
3. Avoid damaging cycles and scrubbers. Do not use heat or sanitise cycles, steel wool pads or balls, or other hard materials that could warp or scratch the parts.
4. Handle sharp attachments. Handle blades and discs with care while washing; keep them covered by the appropriate lid or cover when stored, never exposed.
5. Clean the Motor Base. With the base unplugged, wipe it using a sponge or dishcloth dampened with warm, soapy water. Scrub the actuator area with a small brush if necessary and wipe leakage residue with a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove any base pieces or put the base in the dishwasher.
6. Store the blades in the bowl. With the processor off and unplugged, lower the Chopping Blade onto the Blade Adaptor, then lower the Reversible Slice/Shred Disc onto the adaptor above it.
7. Finish storing the processor. Lock the Work Bowl Lid in place with the Food Pusher nested in the Feed Chute. Store the Endless Chute and Slinger Disc separately.

1. Prepare Baby for cleaning. Unplug the NutriBullet Baby and wait until every moving part has stopped before removing the cup or Batchbowl and blade.
2. Loosen dried food in a cup. Fill the cup halfway with soapy water and twist on the blade. Place the cup-and-blade assembly onto the Motor Base, reconnect power, then press down and twist clockwise to blend for 10–20 seconds. Twist anticlockwise to stop, unplug and wait for the blade to stop. Remove the assembly and untwist the blade; empty the water, lightly scrub away remaining debris and rinse.
3. Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse
4. Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.

1. Prepare Steam + Blend for cleaning. Turn off and unplug the NutriBullet Baby Steam + Blend, then let it cool completely before handling or cleaning parts.
2. Open and separate the used bowl. Allow at least ten minutes for cooling and wait until the appliance is completely cool and all moving parts have stopped. With the appliance unplugged, turn the Work Bowl clockwise off the base. Open the lid and turn its circular bottom grip anticlockwise to separate the lid into two pieces; remove trapped food or water and dry those pieces fully. Lift the Blending Blade vertically out by a non-sharp area using a mitt.
3. Empty and clean the reservoir and blade stem. Remove food from the Work Bowl, untwist the Water Reservoir Cap and discard remaining water. Use a cloth or soft-bristled brush to clear food from the bowl and inside the lid. Clean inside the Blade Stem to remove food or water, then dry it completely.
4. Rinse food away. Rinse the Work Bowl, Work Bowl Lid and Blending Blade under running water after use, holding the sharp blade by a non-sharp area. Clean the blade after every blend so food and mineral residue cannot build up.
5. Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasher
6. Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.

Next steps

1. Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use. NEVER submerge the motor base in water.
2. Check whether descaling is needed. Descale every four weeks, or sooner if limescale appears. Allow the appliance to cool completely after a steam cycle before starting.
3. Descale the Water Reservoir. Empty the Water Reservoir. Use a suitable chemical-free descaler or pour in 240 mL white vinegar. Leave the vinegar for at least 30 minutes, up to 24 hours according to the buildup, then discard it. Rinse with cool water and empty the loosened scale into the sink.
4. Finish descaling. After descaling, boil fresh water several times and discard it to remove remaining scale or vinegar. For the final cleaning cycle, let the appliance cool, fill the Water Reservoir to the 25-minute line and lock its cap clockwise. Fit the Blending Blade vertically onto the Blade Holder, lock the Work Bowl Lid clockwise and lock the bowl anticlockwise onto the base. Connect power, select Steam with the Setting Dial and press Power. The indicator flashes blue while steaming; five beeps mark completion. After the cycle, unplug and cool completely; lift the sharp blade vertically out using a mitt, then discard water from the Work Bowl and reservoir. Repeat descaling if limescale remains.
5. Store Steam + Blend. Unplug the appliance when it will not be used for a while. Keep all pieces together and store the assembled NutriBullet Baby Steam + Blend in a safe, dry, cool place.

1. Prepare the blender for cleaning. Power off and unplug the Magic Bullet To Go 200W. Wait until all moving parts stop, then remove the Blending Cup and Cross Blade assembly from the Motor Base.
2. Rinse the cups, lids and lip rings, brush away dried debris and place them on the dishwasher top rack, or hand-wash with warm, soapy water and rinse. Do not use a sanitise cycle for the cups.
3. Wash the Cross Blade. Hand-wash the Cross Blade and leave its gasket in place; removing the gasket can damage the blade assembly and cause leaks. Keep the Cross Blade out of the dishwasher.
4. Disinfect the blade if desired. After washing, rinse the Cross Blade with a 10% vinegar-and-water solution if additional disinfecting is desired.
5. Dry and inspect the Cross Blade. Dry the Cross Blade completely on its side in a dish drainer so both sides dry. Replace the complete Cross Blade if its gasket is loose or damaged; replace the blade every six months or as needed for performance. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
6. Clear the Motor Base and actuator tabs. With the Magic Bullet To Go 200W unplugged, wipe the inside and outside of its Motor Base using a sponge or cloth dampened with warm, soapy water. Pay attention to sticky debris on the actuator tabs; use a small brush if necessary. Keep the rubber and plastic liners in place. NEVER submerge the motor base in water. Do not put the motor base in the dishwasher.

1. Prepare the blender for cleaning. Power off and unplug the Magic Bullet Value Pack 200W. Wait until all moving parts stop, then remove the Blending Cup and Cross Blade assembly from the Motor Base.
2. Rinse the cups, lids and lip rings, brush away dried debris and place them on the dishwasher top rack, or hand-wash with warm, soapy water and rinse. Do not use a sanitise cycle for the cups.
3. Wash the Cross Blade. Hand-wash the Cross Blade and leave its gasket in place; removing the gasket can damage the blade assembly and cause leaks. Keep the Cross Blade out of the dishwasher.
4. Disinfect the blade if desired. After washing, rinse the Cross Blade with a 10% vinegar-and-water solution if additional disinfecting is desired.
5. Dry and inspect the Cross Blade. Dry the Cross Blade completely on its side in a dish drainer so both sides dry. Replace the complete Cross Blade if its gasket is loose or damaged; replace the blade every six months or as needed for performance. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
6. Clear the Motor Base and actuator tabs. With the Magic Bullet Value Pack 200W unplugged, wipe the inside and outside of its Motor Base using a sponge or cloth dampened with warm, soapy water. Pay attention to sticky debris on the actuator tabs; use a small brush if necessary. Keep the rubber and plastic liners in place. NEVER submerge the motor base in water. Do not put the motor base in the dishwasher.

1. Start cleaning. Turn the Power Control Knob to HOME, unplug the Motor Base and wait for the blades to stop; separate the Cup or Pitcher from the base.
2. Open and empty the cup. If you used the Blending Cup, turn the removed sealed Cup upright with the Cross Blade on top. Unscrew the Cross Blade, then pour out the remaining contents.
3. Open and empty the pitcher. If you used the Pitcher, lift the lid tab with your thumb to loosen and remove the Pitcher Lid, then empty the contents. Twist the Cross Blade clockwise to detach it from the empty Pitcher, following its loosening indicator.
4. Hand-wash the Cup, Pitcher, Cross Blade and accessories with soap and water or use the dishwasher top rack. Keep all components off the bottom rack and avoid heat and sanitise cycles.
5. Clean the base. Wipe the unplugged Motor Base with a damp sponge or cloth. NEVER submerge the motor base in water. Do not remove any pieces from the motor base.
6. Clean the actuator. Use a small dry brush to scrub the actuator clean while the Motor Base is unplugged.
7. Store the blender. Store all components together where they are protected from damage; cover exposed blades with the Cup or Pitcher.

1. Prepare to dismantle the Mini Juicer. Set the Power Button to OFF, unplug and wait until the motor, Sieve and all moving parts have stopped.
2. Remove the juice cup. Tilt the Juice Cup slightly forwards and slide it out from under the spout; immediately turn the Silicone Spout Cap upwards to prevent drips.
3. Release the locking arms. Push upwards from the bottom of each Locking Arm to unclip it, then lower both arms away from the juicer.
4. Remove the pulp bin. Grip the Pulp Bin underneath and pull it away at an angle until it snaps out; keep it angled and slide it away from the Juice Bowl and Cover, then empty it.
5. Lift out the bowl. Lift off the Juice Bowl Cover, then pull upwards from the bottom of the Juice Bowl to remove it with the Sieve still inside.
6. Remove the pusher and sieve. Lift the Food Pusher out of the chute, remove excess pulp from the cover and take the cover, bowl and Sieve to the sink; gently lift the Sieve straight out without touching its blade teeth.

Next steps

1. Rinse the parts. Empty the Juice Bowl and rinse all detached parts except the Motor Base under running water.
2. Clean the sieve properly. Immediately after juicing, use the supplied Cleaning Brush under running water, brushing the outside of the Sieve first and then the inside; avoid its sharp blades.
3. Clean the juice bowl thoroughly. Periodically clean the Juice Bowl with a water-and-vinegar mixture to help avoid mould.
4. Every component except the Motor Base, including the Sieve, is dishwasher-safe; alternatively hand-wash in warm soapy water. Do not use the heat sanitation cycle.
5. Clean the Motor Base. Wipe it with a clean damp cloth. NEVER submerge the motor base in water or other liquid.
6. Store the Mini Juicer. Unplug and wind the cord around the cord wrap underneath; for longer storage, keep all parts together as an assembled juicer in a cool, dry, safe place. Put nothing on the Juice Cup Lid.

1. Prepare Kitchen Express for cleaning. Power off and unplug the Magic Bullet Kitchen Express 250W and wait for every moving part to stop. Turn the Work Bowl anticlockwise to remove it from the Motor Base, then turn its lid anticlockwise and lift it off. Carefully lift out the Chopping Blade before pouring food or scraps from the bowl. If you used the Slice/Shred Disc, remove it using the two larger finger holes before emptying the bowl. If you used the Blending Cup, turn it anticlockwise to remove it, stand it upright with the Cross Blade on top, unscrew the blade and empty the contents.
2. Place every removable component on the dishwasher top rack, or hand-wash with warm, soapy water and rinse. Keep the Motor Base out of the dishwasher and never use a sanitise cycle, which can warp the cups and Work Bowl
3. Handle the sharp attachments. Handle the blades carefully; pick up each blade disc using its two larger finger holes.
4. Clean the Motor Base. With the Motor Base unplugged, wipe it with a sponge or damp cloth. If dried food remains at the actuator system, scrub that area with a small brush until clear. NEVER submerge the motor base in water or other liquid. Do not remove pieces from the base.
5. Store Kitchen Express. Store all pieces together in a safe place where they cannot be damaged or cause harm.

1. Prepare the air fryer for cleaning. Turn off and unplug the Magic Bullet Air Fryer 2.5L after use. Before removing the Fry Pot, check the timer reads 0, the orange indicator light is off and the heating element is completely cool.
2. Remove food scraps. Pull the Fry Pot out of the Base and inspect inside for food scraps. Lift the Crisping Tray by its centre handle and clear remaining scraps from both parts, taking care around the tray’s sharp edges.
3. Wash the Fry Pot and Crisping Tray. Rinse the Fry Pot and Crisping Tray with hot, soapy water. Clean them after each use, as soon as the heating element has cooled, so food does not dry onto the surfaces.
4. Clean the base. Wipe the exterior of the Air Fryer Base with a clean, damp cloth. NEVER submerge the main unit in water or another liquid.
5. Store the air fryer. Store all Magic Bullet Air Fryer 2.5L parts together in a safe place where they cannot be damaged or cause harm.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Choose a safe dishwasher setting. Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.
7. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.

Next steps

1. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
2. Take apart the processor for washing. With power disconnected and the blade or disc stopped, turn the Work Bowl Lid anticlockwise and lift it off, then turn the Work Bowl and Processor Base anticlockwise and lift them from the Motor Base.
3. Remove the blade or disc. Hold the plastic centre hub of the Chopping Blade or Slice/Shred Disc and pull upwards; never tip the Work Bowl to drop a sharp part into your hand.
4. Remove the Work Bowl from the Processor Base. Hold the Processor Base from below with one hand and the Work Bowl handle with the other, turn the bowl anticlockwise and carefully lift it off the Processor Base and Blade Adapter.
5. Remove residue from processor blades and discs. Immerse only the removed Blades or Discs in room-temperature water with 1–2 drops of dish soap, wait 20–30 seconds, then carefully scrub away the loosened debris.
6. Put the Blades, Discs, Work Bowl and Work Bowl Lid on the dishwasher top rack only; never use the heat or sanitise cycle.
7. Keep the Processor Base and Blade Adapter out of the dishwasher and wash them by hand; alternatively hand-wash all Processor Attachment parts with a sponge or cloth, soap and water.

Next steps

1. Take apart the grinder for cleaning. After each use, unplug the Motor Base, wait for the blades to stop, disengage the Coffee & Dry Spice Grinder Attachment and separate the Grinding Cup from the Grinder Blade, handling the sharp blade carefully.
2. Wash the Grinding Cup and Grinder Blade on the dishwasher top rack only, without the heat or sanitise cycle; alternatively hand-wash them with a sponge or cloth, soap and water.
3. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
4. Store the blender. Store the blender upright with nothing placed on top and keep accessories in a safe place; never leave an exposed Rapid Extractor Blade on the motor base without a cup attached.
5. Store the processor blade and disc safely. Fit the Blade Adapter onto the Work Bowl centre shaft, followed by the Chopping Blade; hold the Disc by its centre knob and lower it to the lower storage position about halfway down the adapter shaft without aligning their marks, then attach the Work Bowl Lid.
6. Cover the sharp parts. Keep Blades and Discs covered inside the Processor Attachment with the Work Bowl Lid attached; never leave a Blade or Disc exposed on the Motor Base.
7. Store the grinder. Store the blender and Coffee & Dry Spice Grinder Attachment in a dry, cool, clean place with the power cord safely tucked away; do not use the grinder as a food-storage container or leave an exposed Blade Assembly on the Motor Base.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Reconnect power, invert the sealed cup and blade assembly onto the motor base and turn clockwise until it clicks; the motor starts automatically, so turn the cup anticlockwise to stop after 20–30 seconds and wait for the blades to stop.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
7. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
8. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.

1. Stop and prepare for cleaning. Turn the juicer off, unplug it and wait until the motor and Sieve have completely stopped.
2. Remove the Juice Pitcher. Tilt the Juice Pitcher slightly forwards to separate its flip-top opening from the No-Drip Spout, then slide it out. Immediately turn the No-Drip Spout upwards to prevent drips.
3. Release the Locking Handle. Pull the handle backwards out of the ears on both sides of the Basin Cover, then lower it.
4. Lift the juicing assembly to the sink. Lift the Pulp Basin upwards off the Motor Base with the Basin Cover and Sieve still in place, then take that assembly directly to the sink.
5. Remove the Food Pusher. Lift it out of the Feed Chute.
6. Remove and scrape the Basin Cover. Lift the cover vertically off the Pulp Basin. Use the flat end of the Cleaning Brush to scrape pulp from inside the cover.
7. Remove and clean the Sieve. Gently lift it vertically out of the centre of the Pulp Basin. Clean it immediately with the Cleaning Brush under running water to remove pulp and clear the holes. Do this after every use, taking care not to touch the sharp blade teeth on the flat disc.

Next steps

1. Empty the Pulp Basin. Use the flat end of the Cleaning Brush to scrape out the pulp, then empty it into your waste bin or compost.
2. Rinse the removable parts. Once the Pulp Basin is empty, rinse the detached juicing parts under running water. NEVER submerge the motor base in water or any other liquid. Do not rinse the Motor Base.
3. Clean the No-Drip Spout. Remove the spout, wash it by hand and rinse it with water.
4. Wash the detachable parts. Hand-wash the removable parts in warm soapy water. For the dishwasher option, check the exclusions below.
5. Wipe the Motor Base. Use a clean, damp cloth.
6. Store the clean parts. Store the Juice Pitcher upright with its Lid secured and nothing on top. Keep the remaining pieces in a safe place where they will not be damaged or cause harm.