A loose cup blade or lid, an overfilled container, a blocked juice path or a damaged detachable part can let liquid escape. Check the location of the leak, then use the checks for your Magic Bullet model.
Before removing parts, stop the appliance, disconnect its power supply and wait for all movement to stop; let hot parts and contents cool before handling them.
Is liquid getting into, or coming from inside, the base?
If liquid has entered the motor base or electrical housing, or dark or oily-looking liquid is coming from inside it, stop using it, unplug it only if it is safe to do so, and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase). Keep a rechargeable appliance disconnected from its charger; do not open the housing or run another cycle to test it.
If a leak continues after the checks, or the source is unclear, leave the appliance off and use the same help link. Include the full model name and where the liquid appeared.
If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.
Magic Bullet To Go 200W
The Magic Bullet To Go 200W can leak when its cup is overfilled, its blade is not tightly sealed, or its cup or blade gasket is damaged.
Is the cup filled above its MAX line?
- Check the Magic Bullet To Go 200W cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
- After the motor stops, disconnect power. Once the cup is cool, remove the cup and Cross Blade together, turn the assembly upright, and unscrew the blade.
- Reduce the batch to at or below MAX and screw the Cross Blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
- Look at the join between the Magic Bullet To Go 200W cup and Cross Blade; the blade must sit squarely and form a tight seal.
- With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the Cross Blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
- Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
- Inspect the gasket in the Magic Bullet To Go 200W Cross Blade before reassembling the cup; it must remain seated and intact.
- A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
- Do not pull out the Cross Blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Are the cup, its tabs or the blade housing damaged?
- Empty and clean the Magic Bullet To Go 200W cup, then inspect its sides, rim and fitting tabs for cracks, crazing, cloudiness or breakage.
- Inspect the detached Cross Blade as well. Stop using a cracked cup, damaged tabs or broken blade housing and replace that part with the correct genuine replacement. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
- The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
- Hot ingredients can pressurise the sealed Magic Bullet To Go 200W cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
- If the cup feels hot or warm, stop blending and leave it alone to cool until completely cool; do not try to open it while warm.
- Once cool, point the cup away from your face and body and carefully untwist the Cross Blade to release pressure. Do not force a cup that remains stuck; leave the blender off and use the help route.
Were carbonated or effervescent ingredients used?
- Carbonated ingredients release gas in the sealed Magic Bullet To Go 200W cup. Do not use fizzy drinks for a cup blend.
- Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
- For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
- Blade friction can warm the Magic Bullet To Go 200W mixture during prolonged or repeated blending, allowing pressure to build.
- Keep each continuous blend to no more than one minute.
- Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Was blended food left sealed under the blade?
- Blended food left sealed in the Magic Bullet To Go 200W cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
- After blending and safe pressure release, remove the Cross Blade; use the intended storage lid or transfer the mixture to another suitable container.
- If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
How do I clean and refit the parts after a spill?
- Switch off and unplug the Magic Bullet To Go 200W, then wait until every moving part has stopped.
- Remove the cup and Cross Blade together. Empty the cool vessel and separate its detachable parts for washing.
- Wipe the accessible Magic Bullet To Go 200W Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
- Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; leave the fixed base liners and components in place.
- Wash the detachable cup and blade separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
- Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Magic Bullet Blender Combo
The Magic Bullet Blender Combo can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.
Is the cup filled above its MAX line?
- Check the Magic Bullet Blender Combo cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
- After the motor stops, disconnect power. Once the cup is cool, remove the cup and Cross Blade together, turn the assembly upright, and unscrew the blade.
- Reduce the batch to at or below MAX and screw the Cross Blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
- Look at the join between the Magic Bullet Blender Combo cup and Cross Blade; the blade must sit squarely and form a tight seal.
- With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the Cross Blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
- Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
- Inspect the gasket in the Magic Bullet Blender Combo Cross Blade before reassembling the cup; it must remain seated and intact.
- A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
- Do not pull out the Cross Blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Are the cup or blade assembly damaged?
- Empty and clean the Magic Bullet Blender Combo cup, then inspect its sides and rim for cracks, crazing, cloudiness or breakage.
- Inspect the detached Cross Blade as well. Stop using a cracked cup, a broken blade housing and replace that part with the correct genuine replacement.
- The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
- Hot ingredients can pressurise the sealed Magic Bullet Blender Combo cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
- If the cup feels hot or warm, stop blending and leave it alone to cool at least 30 minutes, and longer until completely cool; do not try to open it while warm.
- When the cup is fully cool, remove it slowly from the base. Point it away from your face and body, cover the Cross Blade with a towel, and slowly untwist it; do not force stuck parts apart.
Were carbonated or effervescent ingredients used?
- Carbonated ingredients release gas in the sealed Magic Bullet Blender Combo cup. Do not use fizzy drinks or effervescent powders for a cup blend.
- Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
- For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Was blended food left sealed under the blade?
- Blended food left sealed in the Magic Bullet Blender Combo cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
- After blending and safe pressure release, remove the Cross Blade; use the intended storage lid or transfer the mixture to another suitable container.
- If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are the cup and blade the correct parts for this model?
- Check that the cup and Cross Blade belong to the Magic Bullet Blender Combo. Use only the cup and blade intended for this model.
- Remove the unsuitable attachment after shutdown and check that its product code matches your machine.
- Use only the genuine matching cup and blade combination. Do not force a thread or reuse a part that cannot sit securely.
Are liquid and solid ingredients below the correct pitcher MAX marks?
- Check the Magic Bullet Blender Combo pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
- Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
- Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
- A lid or opening left unsecured can let the Magic Bullet Blender Combo pitcher splash from the top. Stop the blades before adjusting the lid.
- Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
- Press the lid down to secure it, then press down and twist the Vented Lid Cap until locked. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
- Inspect the Magic Bullet Blender Combo Pitcher, Lid and detachable blade for damage before refitting them.
- Stop using a damaged detachable component and replace it with the correct genuine part for the Combo Blender.
- If correctly fitted, undamaged components still leak, keep the blender off and use the help route in this article.
Did a hot blend splash because it started too fast?
- For a hot blend in the Magic Bullet Blender Combo pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
- Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
- If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
Are the pitcher lid vents blocked?
- Food blocking the Magic Bullet Blender Combo Pitcher Lid vents can trap pressure and cause splattering.
- With the blender off and the mixture cool enough to handle, remove the lid and wash it with soap and water. Clear visible residue from the vent slots, rinse, and check that the openings are unobstructed.
- Refit the lid securely with its vent openings clear. Replace a damaged lid; do not run the pitcher with blocked vents.
Is the removable pitcher blade tightened in the correct direction?
- The Magic Bullet Blender Combo pitcher has a detachable blade; a loose connection can leak at the bottom.
- Empty the pitcher after shutdown. To release the blade, twist it clockwise using the direction indicator on the pitcher; wash the separated blade and pitcher with soap and water, rinse and dry.
- Refit the blade by turning it counter-clockwise onto the bottom of the pitcher until secure. Check the fitted blade before filling the pitcher; replace damaged components before blending.
Were too many cup blends run back-to-back?
- Repeated blending heats the Magic Bullet Blender Combo cup and can build pressure.
- After two consecutive blend cycles, wait at least 10โ15 minutes before another cycle. If the cup is warm, leave it alone for at least 30 minutes and until fully cool before attempting to open it.
- Return the Power Control Knob to HOME when a cycle finishes. Do not run repeated cycles to investigate a leak; complete the filling and attachment checks first.
How do I clean and refit the parts after a spill?
- Switch off and unplug the Magic Bullet Blender Combo, then wait until every moving part has stopped.
- Remove the cup and Cross Blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
- Wipe the Magic Bullet Blender Combo Motor Base surface with a damp sponge or cloth. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
- Use a small dry brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
- Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
- Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Magic Bullet Mini Juicer
A misdirected Silicone Spout Cap, a misplaced or full Juice Cup, or a full Pulp Bin can cause spills or drips from the Magic Bullet Mini Juicer.
Is the Silicone Spout Cap pointing down for juicing or up to prevent drips?
- Turn the Silicone Spout Cap so its nozzle points down while the Magic Bullet Mini Juicer is juicing.
- After switching OFF and waiting for the Sieve to stop, tilt the Juice Cup forwards and slide it away, then turn the Spout Cap upwards immediately to prevent residual drips.
- If it continues dripping with the nozzle raised, inspect the cap for residue or damage while the juicer is unplugged.
Is the Juice Cup correctly aligned, or has it reached MAX?
- Fit the Juice Cup Lid tightly and open the locking lid latch, then angle the cup under the Spout Cap so the nozzle sits directly over and slightly inside the lid opening.
- Level the cup so it fits snugly under the spout; if juice hits the lid rather than entering the opening, stop and reposition it.
- When the Juice Cup reaches the MAX line, stop juicing and wait for the Sieve to stop before removing and emptying the cup to avoid spillage.
Is the Pulp Bin full or not snapped into place?
- With the juicer off, unplugged and the Sieve stopped, unlock the Locking Arms, grip the bottom of the Pulp Bin and pull it away at an angle to unsnap and remove it.
- Empty the bin before washing or refitting; do not let pulp overflow.
- Tilt the Pulp Bin into position at the rear so the back edge of the Juice Bowl Cover slides into its top, then gently push the bottom of the bin until it snaps into place.
- The bin should sit directly under the back edge of the cover; if it will not lock, recheck alignment and damage before starting again.
Are the Sieve holes clogged with dried pulp?
- Lift off the Juice Bowl Cover and raise the Juice Bowl from the Motor Base, then lift the Sieve vertically by its edges without touching the sharp blade teeth.
- Use the Cleaning Brush under running water, brushing the outside before the inside; if pulp has dried onto the Sieve, soak it in hot water for 30 minutes to loosen it.
- Rinse away the pulp and check the holes are clear before refitting; do not restart with blocked or damaged juicing parts.
Are the Juice Bowl, Juice Bowl Cover and both Locking Arms secure?
- Rotate or adjust the Juice Bowl on the Motor Base until seated in its keyed position, then align and press the Sieve onto the motor drive coupling until it clicks.
- Fit the Juice Bowl Cover with the Feed Chute over the Sieve and the Pulp Chute at the rear over the open side of the bowl.
- Raise both Locking Arms, hook their top sections over the cover edge and snap their lower sections down until both stand vertically and lock.
- If either arm cannot lock, remove and reseat the bowl, Sieve and cover rather than holding the lid down by hand.
Is the Feed Chute overloaded or the Food Pusher being forced?
- Start the motor before putting food into the Feed Chute, then feed prepared pieces gradually with the Food Pusher.
- Allow each piece to move down naturally before adding more and avoid excessive force; use no fingers or kitchen utensils in the chute.
- If food stops moving through, switch OFF, unplug and wait for the Sieve to stop before taking the parts apart and clearing the accumulated pulp.
Does juice spill from the Juice Cup during storage?
- Keep the Magic Bullet Mini Juicer Juice Cup upright in the fridge with the Juice Cup Lid tightly sealed and its latch closed.
- Leave nothing on top of the lid and check it is secure; if the cup or lid is damaged, stop using the affected part and replace it.
Is a bowl, cover, container or juicing part cracked or damaged?
- After switching off and unplugging, remove the detachable parts for cleaning and inspect the bowl, cover, collection container and juicing parts for cracks or damage.
- Stop using a damaged detachable part and replace it with the correct genuine part before juicing again; do not try to make a cracked part watertight.
- The replacement must fit and lock securely. If it does not, keep the juicer off.
How do I clean and refit the parts after a spill?
- Set the Power Button to OFF, unplug and wait for the Sieve to stop. Tilt the Juice Cup forward and slide it out, then turn the Silicone Spout Cap upwards.
- Release both Locking Arms by pushing their bottom ends up and letting them fall away. Unsnap the Pulp Bin, lift the Juice Bowl Cover and remove the Juice Bowl and Sieve, holding the Sieve by its edges.
- Empty the pulp and rinse the removable parts. Scrub the Sieve under running water with the Cleaning Brush, outside first and then inside; do not touch the blade teeth.
- Wipe the Motor Base and surrounding spill with a clean damp cloth. NEVER submerge the motor base in water. Hand-wash detached parts with warm soapy water.
- For dried Sieve residue, soak the Sieve in hot water for 30 minutes and brush again. Clean and dry the spill before reassembly.
- Seat the Juice Bowl and click the Sieve onto the coupling. Fit the cover, lock both arms upright, snap the Pulp Bin underneath the back of the cover and position the Juice Cup under the spout.
Magic Bullet Kitchen Express 250W
An overfilled cup or Work Bowl, a loose cross blade, or a dislodged or damaged blade seal can let contents escape from the Magic Bullet Kitchen Express 250W.
Is the cup filled above its MAX line?
- Check the Magic Bullet Kitchen Express 250W cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
- After the motor stops, disconnect power. Once the cup is cool, remove the cup and cross blade together, turn the assembly upright, and unscrew the blade.
- Reduce the batch to at or below MAX and screw the cross blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
- Look at the join between the Magic Bullet Kitchen Express 250W cup and cross blade; the blade must sit squarely and form a tight seal.
- With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the cross blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
- Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the cross-blade seal dislodged or damaged?
- Turn the Magic Bullet Kitchen Express 250W OFF, unplug it and wait for the blades to stop. Let the cup cool before removing the cup and cross-blade assembly.
- Inspect the cross-blade seal without taking the blade assembly apart. If the seal is dislodged or damaged, stop using it and replace the complete cross-blade assembly; do not try another blend with that seal.
Are the cup, its tabs or the blade housing damaged?
- Empty and clean the Magic Bullet Kitchen Express 250W cup and inspect the detachable parts for damage before reassembly.
- Inspect the detached cross blade as well. Stop using a cracked cup, damaged tabs or broken blade housing and replace that part with the correct genuine replacement.
- The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
- Hot ingredients can pressurise the sealed Magic Bullet Kitchen Express 250W cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
- If the cup feels hot or warm, stop blending and leave it alone to cool until completely cool; do not try to open it while warm.
- Once cool, point the cup away from your face and body and carefully untwist the cross blade to release pressure. Do not force a cup that remains stuck; leave the blender off and use the help route.
Were carbonated or effervescent ingredients used?
- Carbonated ingredients release gas in the sealed Magic Bullet Kitchen Express 250W cup. Do not use fizzy drinks for a cup blend.
- Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
- For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
- Long running can warm the Magic Bullet Kitchen Express 250W cup or work bowl and build pressure inside it.
- Keep each continuous blend to no more than one minute.
- Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Are the cup and blade the correct parts for this model?
- Check that the cup and cross blade belong to the Magic Bullet Kitchen Express 250W. Use only the cup and blade intended for this model.
- Remove the unsuitable attachment after shutdown and check that its product code matches your machine.
- Use only the genuine matching cup and blade combination. Do not force a thread or reuse a part that cannot sit securely.
Is the food processor bowl overfilled?
- An overfilled Magic Bullet Kitchen Express 250W work bowl can let ingredients escape. Check the total amount against the bowl MAX line.
- Turn the Power Control Knob to OFF, unplug and wait for the blade to stop. Turn the bowl counter-clockwise off the base and set it on a clean, dry, flat surface; unlock the lid counter-clockwise and remove the chopping blade or disc before transferring excess food. NEVER submerge the motor base in water.
- Refit the intended blade, lock the lid and process the smaller batch. Keep the bowl below MAX when adding liquid as well.
Are the work bowl and lid properly locked?
- The Magic Bullet Kitchen Express 250W work bowl and lid must both be secured before processing.
- With power disconnected, inspect the bowl and lid for trapped food or damage. Wash away residue before refitting the bowl.
- Turn the bowl lid clockwise to lock it, then place the assembled Work Bowl on the Motor Base and turn the bowl clockwise to secure it. The bowl and lid must both lock; replace a damaged detachable component before processing. Buy a replacement bowl (New Zealand).
Is the feed chute being overloaded or food forced through?
- Forcing too much food down the Magic Bullet Kitchen Express 250W feed chute can overload the bowl.
- Stop feeding more ingredients and let food move naturally down the chute; use the supplied Food Pusher without excessive pressure.
- If food remains trapped, switch off and unplug before disassembly. Remove the lid and blade or disc carefully, clear the food and refit the attachments for a smaller batch.
Is the work bowl, lid or its locking area damaged?
- With the Magic Bullet Kitchen Express 250W disconnected and the blades stopped, turn the Work Bowl counter-clockwise off the base. Unlock the lid counter-clockwise and lift out the blade or disc before emptying and cleaning the bowl.
- Inspect the bowl, lid and locking areas for damage; stop using a damaged detachable component and replace it with a genuine matching part. Buy a replacement bowl (New Zealand).
- Refit the replacement using the bowl and lid locking steps above. If the fit remains insecure, keep the appliance off.
How do I clean and refit the parts after a spill?
- Switch off and unplug the Magic Bullet Kitchen Express 250W, then wait until every moving part has stopped.
- For the blending cup, turn the cup/cross blade assembly counter-clockwise off the base and turn it upright before unscrewing the blade. For the Work Bowl, turn the bowl counter-clockwise off the base and set it on a clean, dry, flat surface, then unlock its lid counter-clockwise; remove the chopping blade before emptying food, or lift a disc using its two larger finger holes.
- Use a damp sponge or cloth to wipe the Magic Bullet Kitchen Express 250W Motor Base clean without dismantling it.
- Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
- Wash the detachable cup and blade or bowl attachments separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
- Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.
Magic Bullet Air Fryer 2.5L
An overfilled Fry Pot, oil added for deep frying, or removing the pot too quickly can cause spills or splattering from the Magic Bullet Air Fryer 2.5L.
Is the Fry Pot too full or being used for deep frying?
- With the Magic Bullet Air Fryer 2.5L off, unplugged and completely cool, check how high the food sits in the Fry Pot. Leave about 50 mm of room at the top.
- Remove excess contents before cooking a smaller batch. Do not use the Fry Pot for deep frying with oil.
- Clean the cooled pot and tray before refitting them; if the pot is damaged or will not fit correctly, stop using that detachable part and replace it.
Did hot contents spill while removing or moving the Fry Pot?
- Turn the Magic Bullet Air Fryer 2.5L timer and temperature control to 0, unplug and wait until the frying action has stopped before removing the Fry Pot.
- Use its handle or insulated oven gloves and take the pot out carefully. Pulling it out too quickly can cause splattering; let the appliance cool before moving it or cleaning the spill.
- Refit the clean Fry Pot until it clicks into place. If it cannot seat securely, check the pot for damage before another use.
Is liquid or spilled food left under or around the air fryer?
- After the Magic Bullet Air Fryer 2.5L has been turned off, unplugged and cooled, remove food from the Fry Pot and Crisping Tray.
- Rinse those detachable parts with hot soapy water and wipe the outside of the Air Fryer Base with a clean damp cloth. NEVER submerge the main unit in water.
- Clean and dry the surrounding surface before further use. If liquid has entered the housing, follow the liquid-in-base advice below.
Is the Fry Pot or another detachable part damaged?
- Inspect the clean, cooled Magic Bullet Air Fryer 2.5L Fry Pot and Crisping Tray for damage.
- Stop using a damaged detachable part and replace it. Do not attempt to repair the appliance or its housing yourself.
- Keep the air fryer off if the pot cannot lock into place or liquid continues to escape from an unidentified source.
How do I clean and refit the parts after a spill?
- Set the Magic Bullet Air Fryer 2.5L timer and temperature control to 0, unplug it and allow the heating element to cool completely. The orange indicator light should no longer be illuminated.
- Remove the Fry Pot from the Base. Inspect the pot for food scraps, then pull out the Crisping Tray by its centre handle and remove food from the tray; take care around its sharp edges.
- Rinse the detached Fry Pot and Crisping Tray with hot soapy water. Wipe the exterior of the Air Fryer Base with a clean damp cloth.
- Clean and dry the spill and the work surface. Refit the Fry Pot securely until it clicks; do not use the appliance while wet.
Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: Magic Bullet To Go 200W user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Blender Combo user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Mini Juicer user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Kitchen Express 250W user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Air Fryer 2.5L user guide (PDF)