The NutriBullet Ultra 1200 Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Ultra 1200. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Essentials Set extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Essentials Set stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Essentials Set blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Essentials Set extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Essentials Set blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Essentials Set gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Essentials Set blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Essentials Set cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Essentials Set blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Essentials Set cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Essentials Set blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Mega Pack extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Mega Pack blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 600 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 600 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 600 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Stop and unplug the NutriBullet Ultra 1000 / Ultra 1000 Premium. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1000 / Ultra 1000 Premium blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1000 / Ultra 1000 Premium cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1000 / Ultra 1000 Premium component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1000 / Ultra 1000 Premium gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1000 / Ultra 1000 Premium blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1000 / Ultra 1000 Premium cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1000 / Ultra 1000 Premium blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1000 / Ultra 1000 Premium cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1000 / Ultra 1000 Premium blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet Select 1200 / 2.0 Select 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Select 1200 / 2.0 Select 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Select 1200 / 2.0 Select 1200 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet Select 1200 / 2.0 Select 1200 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet Select 1200 / 2.0 Select 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Select 1200 / 2.0 Select 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Select 1200 / 2.0 Select 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check the ingredients and liquid against the MAX line on the NutriBullet Select 1200 / 2.0 Select 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Select 1200 / 2.0 Select 1200 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet Select 1200 / 2.0 Select 1200 replacement assembly and check its gasket before fitting it to the cup.

The NutriBullet Pro+ 1200 / Pro Plus 1200 extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet Pro+ 1200 / Pro Plus 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Pro+ 1200 / Pro Plus 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Pro+ 1200 / Pro Plus 1200 extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Pro+ 1200 / Pro Plus 1200 blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet Pro+ 1200 / Pro Plus 1200 gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet Pro+ 1200 / Pro Plus 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Pro+ 1200 / Pro Plus 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Pro+ 1200 / Pro Plus 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Pro+ 1200 / Pro Plus 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Pro+ 1200 / Pro Plus 1200 blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet 2.0 Pro 1000 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 2.0 Pro 1000 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 2.0 Pro 1000 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 2.0 Pro 1000 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 2.0 Pro 1000 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet 2.0 Pro 1000 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 2.0 Pro 1000 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 2.0 Pro 1000 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 2.0 Pro 1000 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 2.0 Pro 1000 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet 2.0 Pro 1000 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet 2.0 Pro 1000 replacement assembly and check its gasket before fitting it to the cup.

The NutriBullet 1000 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1000 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1000 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1000 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1000 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 1000 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1000 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 1000 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1000 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1000 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1000 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo 1000 Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo 1000. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo 1000 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo 1000 cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo 1000 component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo 1000 gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo 1000 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo 1000 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo 1000 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo 1000 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo 1000 blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 1200 Series / 12 Piece extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1200 Series / 12 Piece stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1200 Series / 12 Piece blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1200 Series / 12 Piece extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1200 Series / 12 Piece blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 1200 Series / 12 Piece gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1200 Series / 12 Piece blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 1200 Series / 12 Piece cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1200 Series / 12 Piece blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1200 Series / 12 Piece cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1200 Series / 12 Piece blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 1200 Series / 10 Piece extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1200 Series / 10 Piece stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1200 Series / 10 Piece blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1200 Series / 10 Piece extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1200 Series / 10 Piece blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 1200 Series / 10 Piece gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1200 Series / 10 Piece blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 1200 Series / 10 Piece cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1200 Series / 10 Piece blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1200 Series / 10 Piece cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1200 Series / 10 Piece blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 2.0 Pro 1200 easy-twist extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 2.0 Pro 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 2.0 Pro 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 2.0 Pro 1200 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 2.0 Pro 1200 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 2.0 Pro 1200 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet 2.0 Pro 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 2.0 Pro 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 2.0 Pro 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 2.0 Pro 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 2.0 Pro 1200 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet 2.0 Pro 1200 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet 2.0 Pro 1200 replacement assembly and check its gasket before fitting it to the cup.

• Do not remove the gasket. Removing it permanently damages the extractor blade and causes leakage.

• Replace the complete extractor blade when its seal is loose or damaged.
• Inspect your blades before each use. We recommend replacing the extractor blade every 6 months for best performance.

• Keep the extractor blade out of the dishwasher. Hand wash it in warm soapy water and rinse.
• Leave the gasket in place. Dry the blade completely. Stand it on its side in the dish drainer so both sides dry.

• Replace the complete NutriBullet 500 Series / 4 Piece extractor blade if its gasket is loose or damaged; if the gasket is missing, keep the blade unused while support confirms the matching replacement. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the NutriBullet 500 Series blade gasket is loose or damaged, replace the complete extractor blade; do not remove the gasket. Keep a blade with a missing gasket out of use. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• For product code NB5-0407DG, use the compatible NBM-BA031 extractor blade when replacing the complete blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Stop, unplug and wait for all movement to stop. If the sealed cup is warm, let it cool completely before carefully opening it away from your face and body; do not force a stuck cup open.
• Look at the gasket without pulling it out. It must be completely seated before use. Removing it permanently damages the extractor blade and can cause leakage.
• If the gasket is loose, missing or damaged, stop using that blade and replace the complete extractor blade assembly with the approved part for this model. Do not push a loose ring back in or use another appliance’s blade. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check that the extractor blade is screwed tightly onto the cup. Keep the ingredients and liquid at or below MAX, and use cool ingredients and liquid at 21°C or below.
• Check the cup and its three side tabs for cracks, crazing, breaks or rounding. Replace a damaged cup or one with a missing tab.
• If the connection still leaks or does not fit securely, stop using the affected parts and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase). If liquid has entered the motor base, leave the appliance off for assessment.

1. Unplug before removing normally releasing parts. Hand-wash the extractor with warm soapy water and rinse; keep it out of the dishwasher and do not remove its gasket.
2. Dry both sides of the extractor completely. Cups and to-go lids can go on the dishwasher’s top rack, but never use the sanitising cycle, which can warp the plastic.
3. Cleaning cannot repair a loose or damaged gasket. Replace the complete extractor blade if its gasket is not intact and fully seated. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

The NutriBullet 700 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 700 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 700 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 700 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 700 Series blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 700 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 700 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 700 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 700 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 700 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 700 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet Select 1000 / Select 1000 with pitcher stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Select 1000 / Select 1000 with pitcher blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Select 1000 / Select 1000 with pitcher easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Select 1000 / Select 1000 with pitcher blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet Select 1000 / Select 1000 with pitcher gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet Select 1000 / Select 1000 with pitcher blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Select 1000 / Select 1000 with pitcher cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Select 1000 / Select 1000 with pitcher blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check the ingredients and liquid against the MAX line on the NutriBullet Select 1000 / Select 1000 with pitcher cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Select 1000 / Select 1000 with pitcher blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet Select 1000 / Select 1000 with pitcher easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet Select 1000 / Select 1000 with pitcher replacement assembly and check its gasket before fitting it to the cup. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Set the NutriBullet Pro+ Matte Black extractor blade aside and look at the ring without pulling out any remaining rubber.
• For a loose or damaged extractor-blade gasket, replace the complete blade assembly; the gasket is not a separately fitted repair.
• Use the product code N12-1207MK-C when asking for the correct NutriBullet Pro+ Matte Black blade.

• Keep the loose ring with the NutriBullet Pro+ Matte Black component it came from, and photograph both parts.

The NutriBullet 600 Essentials Kit extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Essentials Kit stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Essentials Kit blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Essentials Kit extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Essentials Kit blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 600 Essentials Kit gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Essentials Kit blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 600 Essentials Kit cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Essentials Kit blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Essentials Kit cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Essentials Kit blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Stop and unplug the NutriBullet Ultra 1200 McLaren / Club Pack. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 McLaren / Club Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 McLaren / Club Pack cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 McLaren / Club Pack component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 McLaren / Club Pack gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 McLaren / Club Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Ultra 1200 McLaren / Club Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 McLaren / Club Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 McLaren / Club Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 McLaren / Club Pack blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Ultra 1200 Premium Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Ultra 1200 Premium. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 Premium blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 Premium cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 Premium component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 Premium gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 Premium blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1200 Premium cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 Premium blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 Premium cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 Premium blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 600 Mega Pack extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Mega Pack blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 600 Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 600 Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo 1000 Deluxe Set Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo 1000 Deluxe Set. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo 1000 Deluxe Set blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo 1000 Deluxe Set cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo 1000 Deluxe Set component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo 1000 Deluxe Set gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo 1000 Deluxe Set blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo 1000 Deluxe Set cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo 1000 Deluxe Set blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo 1000 Deluxe Set cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo 1000 Deluxe Set blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo Ultimate Pack Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo Ultimate Pack. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo Ultimate Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo Ultimate Pack cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo Ultimate Pack component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo Ultimate Pack gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo Ultimate Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo Ultimate Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo Ultimate Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo Ultimate Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo Ultimate Pack blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.