• Inspect the Magic Bullet To Go 200W Cross Blade before each use; replace the complete blade if it becomes loose or damaged. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Plan to replace the Cross Blade every six months, or sooner when needed for performance; the guide makes this dependent on use. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Check the blade gasket without pulling it out. If it is worn, torn, loose, damaged or has been removed, stop using the blade and replace the whole Cross Blade; do not fit a loose replacement seal. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Treat increasing noise or unusual vibration as a reason to inspect both the cup and blade for wear, and replace the worn component before continuing. Buy a replacement cross blade (Australia) or cross blade (New Zealand).

• If hard ingredients stop the Cross Blade, unplug and lift the cup/blade assembly from the base; shake the assembly to move the ingredients.
• If still blocked, untwist the blade from a cool cup and use a utensil, never fingers, to free the blades; reattach the blade securely before retrying.
• If cleaning and freeing stuck food do not restore blending, replace a seized blade rather than continuing to run it.
• Always include liquid and do not run with an empty cup; dry or empty operation can damage the blade.

1. Hand-wash the Cross Blade; keep it out of the dishwasher because hot water can damage the outer-rim seal. Leave the gasket seated in the blade housing.
2. If extra disinfecting is desired after washing, rinse with a 10% vinegar/water solution; never remove the seal to clean underneath it.
3. Dry the Cross Blade completely, resting it on its side so both sides can drain.
4. Hand-tighten the blade onto its matching cup before placing it on the base; it should align securely without exposed blades.
5. For storing a blend, remove the blade and fit the flip-top lid. Never store an uncovered blade on the motor base.

• Inspect the Magic Bullet Blender Combo Cross Blade regularly; stop using it if damaged or if the blades do not rotate freely.
• Look at the gasket while leaving it in place. A missing, dislodged or damaged gasket means stop using the attachment and obtain help with a complete replacement; the seal is not individually replaceable.
• Replace the Cross Blade every six months, or earlier if needed, depending on use.
• Use only genuine parts specifically designed for Magic Bullet Blender Combo; do not choose a replacement by appearance.

• If the cup or pitcher is overloaded and the blade stops, switch off, wait for it to stop, unplug and empty some contents; refit the assembly before resuming.
• Do not crush ice or overfill with ice, and do not grind dry grains, cereal or coffee; these can jam or damage the blade.
• Remove stone-fruit pits and keep utensils and other non-food objects out of the vessel before blending.

1. Return the control to HOME, wait until the blade has stopped, unplug, then detach the cup or pitcher from the Motor Base.
2. For the sealed cup, turn it upright with the Cross Blade on top, untwist the blade, then transfer the ingredients.
3. For the pitcher, lift the lid tab and remove the lid, transfer the ingredients, then twist off the Cross Blade following the direction arrows underneath the pitcher.
4. Rinse the blade attachment under lukewarm water without removing the seal; soap-and-water hand washing or the top dishwasher rack may be used, with no heat/sanitise cycle or bottom-rack placement.
5. Securely tighten the Cross Blade to the matching cup or pitcher before reuse, so the threaded joint is sealed.
6. Store all components together where they cannot be damaged, with the blade covered by the cup or pitcher; never leave the blade exposed on the motor base.

• Inspect the Magic Bullet Mini Juicer Sieve before every use; stop using and replace a cracked, bent or damaged Sieve, and do not operate with a cracked or damaged protecting cover.
• Replace the Sieve when it looks dull or works less efficiently after it has been thoroughly cleaned.
• The Magic Bullet Mini Juicer Sieve withstands moderate to heavy use.
• Use genuine replacement parts for the Magic Bullet Mini Juicer.
• After-market parts may cause the Magic Bullet Mini Juicer to malfunction.
• Buy a replacement sieve from the accessories page for Australia or New Zealand.

1. With the motor and Sieve completely stopped, remove the Juice Cup and turn the Silicone Spout Cap upwards.
2. Push up from the bottom of each Locking Arm, then allow the arms to fall away from the cover; do not release them while the Sieve turns.
3. Pull the Pulp Bin away at an angle, remove the cover and lift the Juice Bowl with the Sieve still inside by pulling upwards from under the bowl.
4. Take the bowl and Sieve to the sink; lift the Sieve vertically from its centre without touching the cutting teeth.

• Immediately after juicing, scrub the Sieve under running water with the supplied Cleaning Brush, working outside first and then inside; the holes should be clear of pulp.
• If dried pulp blocks the holes, soak the Sieve in hot water for 30 minutes and brush again; clean after every use to prevent mineral and food buildup.
• Hand-wash the Sieve with warm soapy water or wash it in the dishwasher without the heat sanitation cycle.
• For refitting, seat the Juice Bowl in its keyed position on the unplugged base; hold the Sieve by its top edges, align it with the drive coupling and press until it clicks.
• Place the cover with the Feed Chute above the Sieve and Pulp Chute at the rear; raise and snap both Locking Arms into their vertical locked positions.
• Snap the Pulp Bin into the rear, insert the Food Pusher, turn the Spout Cap down and place the lidded Juice Cup with its open lid hole under the spout before juicing.
• Keep the assembled juicer and its parts together in a safe, cool, dry place for storage, with the power disconnected.

• Check the Magic Bullet Kitchen Express 250W Cross Blade, Chopping Blade and Reversible Slice/Shred Disc; stop using any attachment that appears damaged and replace it with the correct part.
• Use the cup and Cross Blade assembly specifically designed for Magic Bullet Kitchen Express 250W.
• Do not treat poor chopping alone as proof that a blade has expired: first check for overfilling, trapped food and correct assembly.

1. Keep the bowl at or below MAX, leave the feed chute uncrowded, and guide food with the Food Pusher without excessive force.
2. Remove rinds, seeds and pits before processing; do not crush ice or put non-food items into the bowl or cup.
3. Limit operation to one minute at a time to avoid overheating and pressure buildup.
4. Switch OFF, wait for all moving parts to stop and unplug the Motor Base before disassembly.
5. For the Work Bowl, turn it anticlockwise off the Motor Base and place it on a clean, dry, flat surface.
6. Turn the lid anticlockwise to unlock and remove it.
7. Carefully lift out the Chopping Blade and set it aside before pouring food out of the bowl. If using the Slice/Shred Disc, lift it out using its finger holes before emptying the bowl.

Next steps

1. For the blending cup, detach the cup/blade assembly from the Motor Base, turn the cup upright, remove the Cross Blade, then empty the cup before washing.
2. Wash detachable parts on the top dishwasher rack or by hand in warm soapy water, then rinse; do not use a sanitise cycle.
3. Hold a disc through its two larger finger holes when lifting it; keep hands clear of its cutting edges.
4. Fit the replacement Chopping Blade on the bowl shaft, or put the disc on the shaft with the chosen cutting side up; lock the bowl lid and then the bowl clockwise onto the base.
5. For the Cross Blade, screw it onto the matching cup until sealed, invert the assembly and lock the cup clockwise onto the base.
6. Store all parts together where they cannot be damaged or cause harm, and keep a cup attached to any Cross Blade stored on the motor base.