Skip to main content

How can we help?

Why is my full-size blender leaking?

  • Updated

An overfilled pitcher, an unsecured lid or pouring opening, damaged parts, or a poor cup-to-blade seal can cause a full-size blender to leak.

Before removing parts, stop the appliance, disconnect its power supply and wait for all movement to stop; let hot parts and contents cool before handling them.

Is liquid getting into, or coming from inside, the base?

If liquid has entered the motor base or electrical housing, or dark or oily-looking liquid is coming from inside it, stop using it, unplug it only if it is safe to do so, and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase). Keep a rechargeable appliance disconnected from its charger; do not open the housing or run another cycle to test it.

If a leak continues after the checks, or the source is unclear, leave the appliance off and use the same help link. Include the full model name and where the liquid appeared.

If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.

NutriBullet Triple Prep System

The NutriBullet Triple Prep System can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

Is the cup filled above its MAX line?
  • Check the NutriBullet Triple Prep System cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and Extractor Blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the Extractor Blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the NutriBullet Triple Prep System cup and Extractor Blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the Extractor Blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the NutriBullet Triple Prep System Extractor Blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Do not pull out the Extractor Blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Are the cup or blade assembly damaged?
  • Empty and clean the NutriBullet Triple Prep System cup, then inspect its sides and rim for cracks, crazing, cloudiness or breakage.
  • Inspect the detached Extractor Blade as well. Stop using a cracked cup, a broken blade housing and replace that part with the correct genuine replacement. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  • The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed NutriBullet Triple Prep System cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool at least 30 minutes, and longer until completely cool; do not try to open it while warm.
  • When the cup is fully cool, remove it slowly from the base. Point it away from your face and body, cover the Extractor Blade with a towel, and slowly untwist it; do not force stuck parts apart.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed NutriBullet Triple Prep System cup. Do not use fizzy drinks or effervescent powders for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
  • Blade friction can warm the NutriBullet Triple Prep System mixture during prolonged or repeated blending, allowing pressure to build.
  • Keep each continuous blend to no more than one minute.
  • Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Was blended food left sealed under the blade?
  • Blended food left sealed in the NutriBullet Triple Prep System cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
  • After blending and safe pressure release, remove the Extractor Blade; use the intended storage lid or transfer the mixture to another suitable container.
  • If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are the cup and blade the correct parts for this model?
  • Check that the cup and Extractor Blade belong to the NutriBullet Triple Prep System.
  • Remove the unsuitable attachment after shutdown and check that its product code matches your machine.
  • Use only the genuine matching cup and blade combination. Do not force a thread or reuse a part that cannot sit securely.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Triple Prep System pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Triple Prep System pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Press the lid down to secure it, then press down and twist the Vented Lid Cap until locked. The lid must stay fully seated; replace a damaged detachable lid before further use. Keep the pouring spout latched closed during blending.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Triple Prep System pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Triple Prep System off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Triple Prep System pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
Are the pitcher lid vents blocked?
  • Food blocking the NutriBullet Triple Prep System Pitcher Lid vents can trap pressure and cause splattering.
  • With the blender off and the mixture cool enough to handle, remove the lid and wash it with soap and water. Clear visible residue from the vent slots, rinse, and check that the openings are unobstructed.
  • Refit the lid securely with its vent openings clear. Replace a damaged lid; do not run the pitcher with blocked vents.
Is the food processor bowl overfilled?
  • Check the NutriBullet Triple Prep System Work Bowl MAX line; exceeding it can damage the bowl or cover.
  • Power off, unplug and wait for the blades to stop. Turn the Work Bowl Lid counter-clockwise first, then twist the Work Bowl counter-clockwise off the Motor Base. Lift out the blade or disc by its plastic centre before removing excess food.
  • Refit the Blade Adapter and intended blade, secure the Work Bowl to the base clockwise, then lock its Lid clockwise with the arrows aligned. Keep both food and added liquid below the MAX line.
Are the work bowl and lid properly locked?
  • The NutriBullet Triple Prep System work bowl and lid must both be secured before processing.
  • With power disconnected, inspect the bowl and lid for trapped food or damage. Wash away residue before refitting the bowl.
  • Lock the Work Bowl onto the Motor Base first, then turn the Work Bowl Lid clockwise until the arrows align; insert the Food Pusher. Do not operate if a damaged latch prevents a secure fit.
Is the feed chute being overloaded or food forced through?
  • Forcing too much food down the NutriBullet Triple Prep System feed chute can overload the bowl.
  • Stop feeding more ingredients and let food move naturally down the chute; use the supplied Food Pusher without excessive pressure.
  • If food remains trapped, switch off and unplug before disassembly. Remove the lid and blade or disc carefully, clear the food and refit the attachments for a smaller batch.
Is the work bowl, lid or its locking area damaged?
  • With the NutriBullet Triple Prep System disconnected from power, remove the work bowl lid and blade or disc before emptying and cleaning the bowl.
  • Inspect the bowl, lid and locking areas for damage; stop using a damaged detachable component and replace it with a genuine matching part. Buy a replacement bowl (Australia) or bowl (New Zealand).
  • Refit the replacement using the bowl and lid locking steps above. If the fit remains insecure, keep the appliance off.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Triple Prep System, then wait until every moving part has stopped.
  2. Detach the cool Cup and Extractor Blade together or unlock and remove the Pitcher. For the Work Bowl, unlock its Lid counter-clockwise first, then twist the Work Bowl counter-clockwise off the base; carefully lift out the blade or disc by its plastic centre before emptying the food.
  3. Wipe the accessible NutriBullet Triple Prep System Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the Cup, Extractor Blade, Pitcher and Lid, or Work Bowl and Lid, separately with soap and water. Remove the Work Bowl Blade Attachments or Discs and Blade Adapter for cleaning, keep fingers away from cutting edges, then rinse and dry the washable parts.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet Blender Combo 1200

The NutriBullet Blender Combo 1200 (NBF07500-1210DG) can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

For product code NBF07500-1210DG.

Is the cup filled above its MAX line?
  • Check the NutriBullet Blender Combo 1200 cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and easy-twist extractor blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the easy-twist extractor blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the NutriBullet Blender Combo 1200 cup and easy-twist extractor blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the easy-twist extractor blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the NutriBullet Blender Combo 1200 easy-twist extractor blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Do not pull out the easy-twist extractor blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Is the bottom of the easy-twist extractor blade cracked or broken?
  • After cleaning the NutriBullet Blender Combo 1200 easy-twist extractor blade, inspect the underside for cracks or breakage.
  • Replace a damaged easy-twist extractor blade before blending again. Keep the blade assembly intact; removing its components can permanently damage it and cause leakage. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  • Refit the matching replacement securely to the cup. If the assembly will not tighten correctly, leave the blender off.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed NutriBullet Blender Combo 1200 cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool until completely cool; do not try to open it while warm.
  • Once cool, point the cup away from your face and body and carefully untwist the easy-twist extractor blade to release pressure. Do not force a cup that remains stuck; leave the blender off and use the help route.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed NutriBullet Blender Combo 1200 cup. Do not use fizzy drinks for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
  • Blade friction can warm the NutriBullet Blender Combo 1200 mixture during prolonged or repeated blending, allowing pressure to build.
  • Keep each continuous blend to no more than one minute.
  • Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Was blended food left sealed under the blade?
  • Blended food left sealed in the NutriBullet Blender Combo 1200 cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
  • After blending and safe pressure release, remove the easy-twist extractor blade; use the intended storage lid or transfer the mixture to another suitable container.
  • If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Blender Combo 1200 pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Blender Combo 1200 pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Seat the lid fully and secure the vented lid cap before blending. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Blender Combo 1200 pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Blender Combo 1200 off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Blender Combo 1200 pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Blender Combo 1200, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Blender Combo 1200 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet SmartSense Blender โ€” Australia

Keep the NutriBullet SmartSense Blender NBF07600 off and give support the product code and leak location for the correct checks.

The cleaning steps below cover accessible spills.

How do I clean and refit the parts after a spill?
  1. Wipe accessible splashes from the NutriBullet SmartSense Blender Motor Base with a damp cloth. NEVER submerge the motor base in water.
  2. Hand-wash the Tamper with soap and water. The Pitcher is dishwasher-safe; the Tamper and Motor Base must stay out of the dishwasher.

NutriBullet Smart Touch Blender Combo

The NutriBullet Smart Touch Blender Combo can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

Is the cup filled above its MAX line?
  • Check the NutriBullet Smart Touch Blender Combo cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and easy-twist extractor blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the easy-twist extractor blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the NutriBullet Smart Touch Blender Combo cup and easy-twist extractor blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the easy-twist extractor blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the NutriBullet Smart Touch Blender Combo easy-twist extractor blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Do not pull out the easy-twist extractor blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Are the cup, its tabs or the blade housing damaged?
  • Empty and clean the NutriBullet Smart Touch Blender Combo cup, then inspect its sides, rim and fitting tabs for cracks, crazing, cloudiness or breakage.
  • Inspect the detached easy-twist extractor blade as well. Stop using a cracked cup, damaged tabs or broken blade housing and replace that part with the correct genuine replacement.
  • The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed NutriBullet Smart Touch Blender Combo cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool until completely cool; do not try to open it while warm.
  • Once cool, point the cup away from your face and body and carefully untwist the easy-twist extractor blade to release pressure. Do not force a cup that remains stuck; leave the blender off and use the help route.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed NutriBullet Smart Touch Blender Combo cup. Do not use fizzy drinks for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
  • Blade friction can warm the NutriBullet Smart Touch Blender Combo mixture during prolonged or repeated blending, allowing pressure to build.
  • Keep each continuous blend to no more than one minute.
  • Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Smart Touch Blender Combo pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Smart Touch Blender Combo pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Seat the lid fully and secure the vented lid cap before blending. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Smart Touch Blender Combo pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Smart Touch Blender Combo off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Smart Touch Blender Combo pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Smart Touch Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Smart Touch Blender Combo Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet Power Core Blender

An overfilled pitcher, an unsecured lid or lid opening, or a damaged pitcher can let liquid escape from the NutriBullet Power Core Blender.

Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Power Core Blender pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Power Core Blender pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Fit the Pitcher Lid with its cap attached, aligning the rear loop opposite the spout with the pitcher handle. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Power Core Blender pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Power Core Blender off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Power Core Blender pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
Are the pitcher lid vents blocked?
  • Food blocking the NutriBullet Power Core Blender Pitcher Lid vents can trap pressure and cause splattering.
  • With the blender off and the mixture cool enough to handle, remove the lid and wash it with soap and water. Clear visible residue from the vent slots, rinse, and check that the openings are unobstructed.
  • Refit the lid securely with its vent openings clear. Replace a damaged lid; do not run the pitcher with blocked vents.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Power Core Blender, then wait until every moving part has stopped.
  2. Unlock and remove the Pitcher from the Motor Base, take off the Lid and empty the remaining ingredients.
  3. Wipe the accessible NutriBullet Power Core Blender Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet Blender Combo 1000

The NutriBullet Blender Combo 1000 can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

Is the cup filled above its MAX line?
  • Check the NutriBullet Blender Combo 1000 cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and easy-twist extractor blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the easy-twist extractor blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the NutriBullet Blender Combo 1000 cup and easy-twist extractor blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the easy-twist extractor blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the NutriBullet Blender Combo 1000 easy-twist extractor blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Do not pull out the easy-twist extractor blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Is the bottom of the easy-twist extractor blade cracked or broken?
  • After cleaning the NutriBullet Blender Combo 1000 easy-twist extractor blade, inspect the underside for cracks or breakage.
  • Replace a damaged easy-twist extractor blade before blending again. Keep the blade assembly intact; removing its components can permanently damage it and cause leakage. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  • Refit the matching replacement securely to the cup. If the assembly will not tighten correctly, leave the blender off.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed NutriBullet Blender Combo 1000 cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool until completely cool; do not try to open it while warm.
  • Once cool, point the cup away from your face and body and carefully untwist the easy-twist extractor blade to release pressure. Do not force a cup that remains stuck; leave the blender off and use the help route.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed NutriBullet Blender Combo 1000 cup. Do not use fizzy drinks for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
  • Blade friction can warm the NutriBullet Blender Combo 1000 mixture during prolonged or repeated blending, allowing pressure to build.
  • Keep each continuous blend to no more than one minute.
  • Do not restart repeatedly to investigate a leak. Let the contents cool, then finish the cup, blade and filling checks before using the blender again.
Was blended food left sealed under the blade?
  • Blended food left sealed in the NutriBullet Blender Combo 1000 cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
  • After blending and safe pressure release, remove the easy-twist extractor blade; use the intended storage lid or transfer the mixture to another suitable container.
  • If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Blender Combo 1000 pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Blender Combo 1000 pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Seat the lid fully and secure the vented lid cap before blending. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Blender Combo 1000 pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Blender Combo 1000 off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Blender Combo 1000 pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Blender Combo 1000, then wait until every moving part has stopped.
  2. Remove the cup and easy-twist extractor blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Blender Combo 1000 Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet Power Core Blender Combo

The NutriBullet Power Core Blender Combo (NBF07202AK) can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

For product code NBF07202AK.

Is the cup filled above its MAX line?
  • Check the NutriBullet Power Core Blender Combo cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and Extractor Blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the Extractor Blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the NutriBullet Power Core Blender Combo cup and Extractor Blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the Extractor Blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the NutriBullet Power Core Blender Combo Extractor Blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Keep the damaged Extractor Blade off the appliance until the correct replacement is available; do not continue blending with a missing or damaged gasket.
Are the cup or blade assembly damaged?
  • Empty and clean the NutriBullet Power Core Blender Combo Cup. Inspect it for cracking, cloudiness or other damage before refitting it.
  • Check the detached Extractor Blade and its gasket as well. Stop using a damaged Cup or blade assembly and replace the affected detachable part.
  • The replacement must fit securely. If correctly fitted, sound parts still leak, keep the blender off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed NutriBullet Power Core Blender Combo cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool at least 30 minutes, and longer until completely cool; do not try to open it while warm.
  • When the cup is fully cool, remove it slowly from the base. Point it away from your face and body, cover the Extractor Blade with a towel, and slowly untwist it; do not force stuck parts apart.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed NutriBullet Power Core Blender Combo cup. Do not use fizzy drinks or effervescent powders for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Did blending run for too long or repeat without a rest?
  • Blade friction can heat the NutriBullet Power Core Blender Combo mixture and build pressure inside the Cup.
  • Never blend for longer than one minute, and do not run consecutive one-minute cycles. Allow the contents to settle for at least 10โ€“15 minutes before another cycle; a hot or warm Cup must follow the longer cooling procedure above.
  • Once the Cup is fully cool, open it slowly and carefully, pointing it away from your body, to release built-up pressure before another blend. Complete the fitting and filling checks first.
Was blended food left sealed under the blade?
  • Blended food left sealed in the NutriBullet Power Core Blender Combo cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
  • After blending and safe pressure release, remove the Extractor Blade; use the intended storage lid or transfer the mixture to another suitable container.
  • If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are the cup and blade the correct parts for this model?
  • Check that the cup and Extractor Blade belong to the NutriBullet Power Core Blender Combo.
  • Remove the unsuitable attachment after shutdown and check that its product code matches your machine.
  • Use only the genuine matching cup and blade combination. Do not force a thread or reuse a part that cannot sit securely.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the NutriBullet Power Core Blender Combo pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the NutriBullet Power Core Blender Combo pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Position the Pour Spout Cover opposite the handle. Align the lid interlocking mechanism with the opening at the top of the handle and push down securely; close the Pour Spout Cover. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the clean NutriBullet Power Core Blender Combo pitcher, its base and fitting area for cracks, crazing, cloudiness or breakage.
  • Replace a damaged pitcher or detachable lid before using it again; do not keep blending to see whether a crack leaks more.
  • If liquid continues to escape from the bottom of a sound, correctly fitted pitcher, keep the NutriBullet Power Core Blender Combo off and use the help route for the fault.
Did a hot blend splash because it started too fast?
  • For a hot blend in the NutriBullet Power Core Blender Combo pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
Are the pitcher lid vents blocked?
  • Food blocking the NutriBullet Power Core Blender Combo Pitcher Lid vents can trap pressure and cause splattering.
  • With the blender off and the mixture cool enough to handle, remove the lid and wash it with soap and water. Clear visible residue from the vent slots, rinse, and check that the openings are unobstructed.
  • Refit the lid securely with its vent openings clear. Replace a damaged lid; do not run the pitcher with blocked vents.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the NutriBullet Power Core Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and Extractor Blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the accessible NutriBullet Power Core Blender Combo Motor Base surfaces with a sponge or cloth dampened with warm soapy water. NEVER submerge the motor base in water. Do not remove the motor base's housing parts.
  4. Use a small brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

NutriBullet Power Core Plus

Keep the NutriBullet Power Core Plus off and give support the product code and leak location for the correct checks.

  1. Leave the NutriBullet Power Core Plus switched off while the source of the liquid is unresolved. NEVER submerge the motor base in water.
  2. Read the model code on the appliance label and include it with a description of where the liquid appears when you take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase). Do not remove seals or open the housing to investigate.

Magic Bullet Blender Combo

The Magic Bullet Blender Combo can leak from an overfilled pitcher or cup, an unsecured pitcher lid, a loose cup blade, or a damaged vessel or blade seal.

Is the cup filled above its MAX line?
  • Check the Magic Bullet Blender Combo cup with all ingredients and liquid included; filling above MAX leaves too little room and can let the contents escape.
  • After the motor stops, disconnect power. Once the cup is cool, remove the cup and Cross Blade together, turn the assembly upright, and unscrew the blade.
  • Reduce the batch to at or below MAX and screw the Cross Blade back on tightly. The mixture must remain below the marked limit; divide a large recipe between batches.
Is the blade squarely aligned and tightly attached?
  • Look at the join between the Magic Bullet Blender Combo cup and Cross Blade; the blade must sit squarely and form a tight seal.
  • With power disconnected, remove the cool cup assembly and stand it blade-side up. Unscrew the Cross Blade, then hand-wash the cup and blade using warm soapy water without touching the cutting edges.
  • Rinse and dry the parts. Align the blade with the cup and hand-tighten it securely before returning the complete assembly to the base; stop using any attachment that cannot be secured.
Is the blade gasket loose, missing, removed or damaged?
  • Inspect the gasket in the Magic Bullet Blender Combo Cross Blade before reassembling the cup; it must remain seated and intact.
  • A loose, missing, torn or damaged gasket means the blade assembly must not be used. Replace the affected blade assembly rather than operating it with an incomplete seal.
  • Do not pull out the Cross Blade gasket or dismantle the blade to clean underneath it; wash the accessible surfaces and dry the assembly completely.
Are the cup or blade assembly damaged?
  • Empty and clean the Magic Bullet Blender Combo cup, then inspect its sides and rim for cracks, crazing, cloudiness or breakage.
  • Inspect the detached Cross Blade as well. Stop using a cracked cup, a broken blade housing and replace that part with the correct genuine replacement.
  • The replacement should attach securely without force. If sound parts still leak after correct fitting and filling, keep the appliance off and use the help route in this article.
Did hot or warm ingredients pressurise the cup?
  • Hot ingredients can pressurise the sealed Magic Bullet Blender Combo cup and push contents out. Start a new cup blend only with refrigerated or room-temperature ingredients.
  • If the cup feels hot or warm, stop blending and leave it alone to cool at least 30 minutes, and longer until completely cool; do not try to open it while warm.
  • When the cup is fully cool, remove it slowly from the base. Point it away from your face and body, cover the Cross Blade with a towel, and slowly untwist it; do not force stuck parts apart.
Were carbonated or effervescent ingredients used?
  • Carbonated ingredients release gas in the sealed Magic Bullet Blender Combo cup. Do not use fizzy drinks or effervescent powders for a cup blend.
  • Stop further blending if the mixture is pressurised. Follow the warm-cup cooling steps above before opening a warm vessel.
  • For the next batch, use a non-carbonated liquid and check the ingredient list before adding a powder or supplement.
Was blended food left sealed under the blade?
  • Blended food left sealed in the Magic Bullet Blender Combo cup can ferment and release gas, so the blade assembly must not be used as a storage lid.
  • After blending and safe pressure release, remove the Cross Blade; use the intended storage lid or transfer the mixture to another suitable container.
  • If an old blend has left the cup warm or stuck, stop handling it and use the warm-cup procedure above. Never add another blending cycle to try to release it.
Are the cup and blade the correct parts for this model?
  • Check that the cup and Cross Blade belong to the Magic Bullet Blender Combo.
  • Remove the unsuitable attachment after shutdown and check that its product code matches your machine.
  • Use only the genuine matching cup and blade combination. Do not force a thread or reuse a part that cannot sit securely.
Are liquid and solid ingredients below the correct pitcher MAX marks?
  • Check the Magic Bullet Blender Combo pitcher markings before running the blender. Keep liquids below the liquid MAX line and solids below the solid MAX line where separate marks are provided.
  • Switch off, disconnect power and wait for the blades to stop, then remove the pitcher and reduce an excessive batch.
  • Refit the closed lid before blending again. The ingredients must stay within the appropriate MAX mark after everything has been added.
Are the pitcher lid and its opening securely closed?
  • A lid or opening left unsecured can let the Magic Bullet Blender Combo pitcher splash from the top. Stop the blades before adjusting the lid.
  • Remove the lid and wash food deposits from the lid and pitcher contact surfaces with soap and water, then rinse.
  • Press the lid down to secure it, then press down and twist the Vented Lid Cap until locked. The lid must stay fully seated; replace a damaged detachable lid before further use.
Is the pitcher cracked, cloudy or damaged?
  • Inspect the Magic Bullet Blender Combo Pitcher, Lid and detachable blade for damage before refitting them.
  • Stop using a damaged detachable component and replace it with the correct genuine part for the Combo Blender.
  • If correctly fitted, undamaged components still leak, keep the blender off and use the help route in this article.
Did a hot blend splash because it started too fast?
  • For a hot blend in the Magic Bullet Blender Combo pitcher, the fitted vented lid and the correct fill level help control splashes. Hot ingredients must never be moved to a sealed blending cup.
  • Start the pitcher blend on LOW and increase speed only after ingredients are mixed and the surface is steady.
  • If the mixture splashes, stop the motor and let it settle before checking the lid and amount. Open the lid cautiously because steam can escape.
Are the pitcher lid vents blocked?
  • Food blocking the Magic Bullet Blender Combo Pitcher Lid vents can trap pressure and cause splattering.
  • With the blender off and the mixture cool enough to handle, remove the lid and wash it with soap and water. Clear visible residue from the vent slots, rinse, and check that the openings are unobstructed.
  • Refit the lid securely with its vent openings clear. Replace a damaged lid; do not run the pitcher with blocked vents.
Is the removable pitcher blade tightened in the correct direction?
  • The Magic Bullet Blender Combo pitcher has a detachable blade; a loose connection can leak at the bottom.
  • Empty the pitcher after shutdown. To release the blade, twist it clockwise using the direction indicator on the pitcher; wash the separated blade and pitcher with soap and water, rinse and dry.
  • Refit the blade by turning it counter-clockwise onto the bottom of the pitcher until secure. Check the fitted blade before filling the pitcher; replace damaged components before blending.
Were too many cup blends run back-to-back?
  • Repeated blending heats the Magic Bullet Blender Combo cup and can build pressure.
  • After two consecutive blend cycles, wait at least 10โ€“15 minutes before another cycle. If the cup is warm, leave it alone for at least 30 minutes and until fully cool before attempting to open it.
  • Return the Power Control Knob to HOME when a cycle finishes. Do not run repeated cycles to investigate a leak; complete the filling and attachment checks first.
How do I clean and refit the parts after a spill?
  1. Switch off and unplug the Magic Bullet Blender Combo, then wait until every moving part has stopped.
  2. Remove the cup and Cross Blade together or unlock and remove the pitcher. Empty the cool vessel and separate its detachable parts for washing.
  3. Wipe the Magic Bullet Blender Combo Motor Base surface with a damp sponge or cloth. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
  4. Use a small dry brush to loosen sticky debris around the actuator area while the base remains unplugged; keep the Motor Base intact.
  5. Wash the detachable cup and blade, pitcher and lid separately with soap and water, keeping fingers away from the cutting edges. Rinse the washable parts and dry them before reassembly.
  6. Check that the accessible base is free of food and moisture before refitting the clean parts. If liquid has entered the housing, follow the liquid-in-base advice in this article instead of restarting.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: NutriBullet Triple Prep System user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Smart Touch Blender Combo user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Power Core Blender user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Blender Combo 1000 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Power Core Blender Combo user guide (PDF)

The full steps for this model are in its user guide: Magic Bullet Blender Combo user guide (PDF)

Related articles

Contact us