Yes to outdoor use where the official instructions permit dry, temperate conditions; store indoors where required.
Before use, make sure the area under and beside the blender is clean and dry. Turn the blender off and wait for the blades to stop before storing it.
Applies to
- NutriBullet Portable Blender / Portable Blender McLaren
- NutriBullet Flip Stainless
- NutriBullet Flex Portable / Flex Portable McLaren
- NutriBullet GO
- NutriBullet Flip Tritan
NutriBullet Portable Blender / Portable Blender McLaren
Yes, the Portable Blender can be used outside in dry, temperate conditions; no to leaving it stored outdoors, because the official guidance says to keep it indoors in a temperature-controlled place when not in use.
Where can I use it?
- Choose a dry, level, stable surface. Do not use near water or in rain or snow.
- Keep out of direct sunlight and away from open flames, other heat sources, and areas with excessive dirt, dust, oil or chemicals.
- Do not blend while driving, operating machinery, cycling, walking or doing another activity that needs your full attention.
- Keep storage and ambient charging temperatures within 10°C–40°C; avoid extreme heat and cold.
- Do not leave the blender inside a vehicle, particularly in summer or winter.
- Do not use in a potentially explosive atmosphere, including fuel stations, fuel or chemical storage/transfer areas, below decks on boats, or places with airborne grain dust or metal powder.
- Keep the USB-C port free of dust and moisture; put only the correct charger into it.
- If the exterior gets wet, wipe it gently with a clean, dry cloth. Never dry it with a hair dryer, clothes dryer, oven or microwave.
- Do not crush or drop the Motor Base. Inspect components for damage or wear before use and stop using damaged parts.
How should I store it after use?
- Power off and disconnect the charger before storing, cleaning or taking parts apart.
- Do not leave blended food sealed in the Cup for prolonged periods: it can spoil, ferment and build pressure. Open the drinking lid carefully after the blade stops.
- Store upright in a safe place with the blades covered, and do not stack anything on top of the blender.
- Keep the Cup attached to the Motor Base during storage to cover the blades.
Never submerge the Motor Base in water or any other liquid.
Never store the Portable Blender in the freezer.
Do not charge or handle the blender if it is wet, if it is in an area that could get wet, or with wet hands.
Extreme heat or cold can drain and damage the battery.
NutriBullet Flip Stainless
Keep the Flip in a dry, temperature-controlled location.
Where can I use it?
- Choose a dry, level, stable surface. Do not use near water or in rain or snow.
- Keep out of direct sunlight and away from open flames, other heat sources, and areas with excessive dirt, dust, oil or chemicals.
- Do not blend while driving, operating machinery, cycling, walking or doing another activity that needs your full attention.
- Keep storage and ambient charging temperatures within 10°C–40°C; avoid extreme heat and cold.
- Do not put the blender in a refrigerator or freezer.
- Do not use in a potentially explosive atmosphere, including fuel stations, fuel or chemical storage/transfer areas, below decks on boats, or places with airborne grain dust or metal powder.
- Keep the USB-C port free of dust and moisture; put only the correct charger into it.
- If the exterior gets wet, wipe it gently with a clean, dry cloth. Never dry it with a hair dryer, clothes dryer, oven or microwave.
- Do not crush or drop the Motor Base. Inspect components for damage or wear before use and stop using damaged parts. NEVER submerge the entire Motor Base, Blade, and Lid in water.
How should I store it after use?
- Power off and disconnect the charger before storing, cleaning or taking parts apart.
- Do not leave blended food sealed in the Cup for prolonged periods: it can spoil, ferment and build pressure. Open the drinking lid carefully after the blade stops.
- Store upright in a safe place with the blades covered, and do not stack anything on top of the blender.
- Use either the Cup or Blade Cover to cover the Motor Base, Blade, and Lid. Keep the storage location dry and temperature-controlled.
- For the separate To-Go Lid, keep the Cup upright because that lid is not leak-proof.
- Unplug and leave the blender undisturbed for 90 seconds until it fully shuts down before fitting or removing parts.
NutriBullet Flex Portable / Flex Portable McLaren
Yes, the Flex can be used outside in dry, temperate conditions; the recommended storage temperature is 10°C–40°C.
Where can I use it?
- Choose a dry, level, stable surface. Do not use near water or in rain or snow.
- Keep out of direct sunlight and away from open flames, other heat sources, and areas with excessive dirt, dust, oil or chemicals.
- Do not blend while driving, operating machinery, cycling, walking or doing another activity that needs your full attention.
- Keep storage and ambient charging temperatures within 10°C–40°C; avoid extreme heat and cold.
- Do not leave the blender inside a vehicle, particularly in summer or winter.
- Do not use in a potentially explosive atmosphere, including fuel stations, fuel or chemical storage/transfer areas, below decks on boats, or places with airborne grain dust or metal powder.
- Keep the USB-C port free of dust and moisture; put only the correct charger into it.
- If the exterior gets wet, wipe it gently with a clean, dry cloth. Never dry it with a hair dryer, clothes dryer, oven or microwave.
- Do not crush or drop the Motor Base. Inspect components for damage or wear before use and stop using damaged parts.
How should I store it after use?
- Power off and disconnect the charger before storing, cleaning or taking parts apart.
- Do not leave blended food sealed in the Cup for prolonged periods: it can spoil, ferment and build pressure. Open the drinking lid carefully after the blade stops.
- Store upright in a safe place with the blades covered, and do not stack anything on top of the blender.
- Keep the Blade Block secured to the Blending Cup, with the Sip Lid with Carry Loop attached, and assemble to the Motor Base. Keep it out of infants’ and small children’s reach.
- Dry the Sip Lid with Carry Loop fully before storing so moisture is not trapped in the gasket or seal.
Do not store the Flex in the freezer.
Do not charge or handle the Flex if it is wet, if it is in an area that could get wet, or with wet hands.
NutriBullet GO
Use it in a dry area, and store the parts together in a safe place where they cannot be damaged or cause harm.
Where can I use NutriBullet GO?
- Use the blender on a dry, level surface and never operate when wet. Clean up and dry any spillage under, around or on the blender before continuing.
- Keep the USB cable away from hot surfaces and extreme heat; do not let it knot, tangle or fray.
- Check the cable and all parts for damage; do not use damaged parts or an appliance that has been dropped or malfunctions.
How should I store NutriBullet GO?
- Make sure no light is on, the motor has stopped and the blades have completely stopped before storing.
- Fit the Cup or Blade Cap over the sharp blades, and store all parts together in a safe place where they cannot be damaged or cause harm.
- Do not leave a blended mixture sealed without releasing pressure; fruit and vegetable sugars can ferment and build pressure.
- Never burn the appliance; lithium-ion batteries need proper recycling.
NutriBullet Flip Tritan
Store the Flip Tritan in a dry, temperature-controlled location, and do not use it in wet, rainy or snowy conditions.
Which surroundings must I avoid?
- Use a level, stable surface; do not use near water or in wet, rainy or snowy conditions.
- Keep away from flames, heat, excessive dirt, dust, oil, chemicals and direct sunlight; do not expose the blender to extreme temperatures.
- Do not blend while driving, operating machinery, cycling, walking or doing another activity that needs your full attention.
How should I store it after use?
- Unplug and allow the blender to shut down completely before storing or fitting parts; automatic shutdown takes 90 seconds without activity. NEVER submerge the entire Motor Base, Blade, and Lid in water.
- Keep it in a dry, temperature-controlled location; the recommended storage and ambient charging temperature is 10°C–40°C.
- Cover the blades with the Cup or Blade Cover, and do not stack objects on the blender.
Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: NutriBullet Portable Blender / Portable Blender McLaren user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Flip Stainless user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Flex Portable / Flex Portable McLaren user guide (PDF)
The full steps for this model are in its user guide: NutriBullet GO user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Flip Tritan user guide (PDF)