1. Power off and unplug the Motor Base, wait for every blade or disc to stop, and detach the Cup, Pitcher or Work Bowl.
2. Clean the Extractor Blade immediately with a small brush or sponge dampened with soapy water.
3. Rinse or scrub food off the Blade Adapter, blade attachments, Cups, Food Pusher and To-Go Lids before putting these dishwasher-safe accessories in the dishwasher.
4. Wash the Pitcher and Pitcher Lid in the dishwasher or with soap and water by hand; keep your hands clear of the sharp pitcher blades.
5. Remove the blade or disc and Blade Adapter from the Work Bowl before washing the Work Bowl and Work Bowl Lid in the dishwasher or by hand.
6. Wash the Tamper by hand with soap and water.

Next steps

1. Use no heat or sanitise cycle for any part; do not sanitise parts in a microwave, oven, air fryer, stovetop pot or boiling water.
2. Wipe the Motor Base with a warm sponge or cloth dampened with soapy water, brush the actuator system, and dry the base. Keep its vents clear.
3. For residue in a Cup, add room-temperature water to the MAX line and 1–2 drops of dish soap, fit the Extractor Blade, and blend 20–30 seconds; unplug, scrub and rinse.
4. For Pitcher residue, half-fill it with water and 1–2 drops of dish soap, fit the lid, and blend 20–30 seconds; unplug, scrub and rinse.
5. Replace Cups, Pitchers or Work Bowls with cracks, cloudiness, warping or damage. Replace the Extractor Blade if it cannot rotate freely or its gasket is missing or damaged. Buy a replacement pitcher (Australia) or pitcher (New Zealand). Buy a replacement work bowl (Australia) or work bowl (New Zealand). Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
6. Store the blender upright with nothing on top. In the Work Bowl, place the Blade Adapter on the centre shaft, then the Chopping Blade, Dough Blade and Slice/Shred Disc; fit the Work Bowl Lid so no cutting edges remain exposed.

The care steps below cover product code NBF07500-1210DG. Check the code on the appliance before following these steps.

1. Switch off, unplug and wait for the blades to stop; detach the Cup and Easy-Twist Extractor Blade from the Motor Base.
2. Clean the Easy-Twist Extractor Blade immediately after use with soap and water, using a small brush or sponge to dislodge food without touching its sharp edges.
3. Leave every component of the Easy-Twist Extractor Blade in place; taking it apart can permanently damage it and cause leakage.
4. Dry the Easy-Twist Extractor Blade completely. Inspect its underside for cracks or breaks and replace the assembly if damaged or loose. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Rinse and briefly brush the Cups and To-Go Lids before washing them on the dishwasher top rack; never use the sanitise cycle because it can warp the plastic.
6. For stubborn food in the Cup, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, attach the blade, and blend for 20–30 seconds; unplug, then scrub and rinse.
7. Wipe the Motor Base with a sponge or cloth dampened with warm, soapy water, and use a small brush on the actuator area if needed. Do not remove base parts.

Next steps

1. Rinse and brush the Pitcher before washing it in the dishwasher, or hand-wash it with soap and water; avoid the sanitise cycle and scrub stuck food with a dish brush or sponge.
2. Inspect the Pitcher and its twisting threads for cracks, crazing or breaks. Replace a damaged Pitcher and do not use one that fails to align correctly with the blade. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
3. Hand-wash the Tamper with soap and water, using a dish brush or sponge for stuck food.
4. For stubborn Pitcher residue, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, secure the lid, and blend for 20–30 seconds; unplug and scrub away the loosened food.
5. Store the blender upright with nothing on top and the remaining accessories protected from damage; never leave the blade exposed on the Motor Base without a Cup attached.
6. Store the Pitcher upright with its lid secured and nothing on top of the lid.

• It comes with a 1500-watt motor base, a 1.8 L pitcher with an integrated blade, a pitcher lid with a vented lid cap and a tamper.

• The pitcher is plastic. Never wash it on the dishwasher's heat or sanitise cycle, as high temperatures can warp the plastic.

• Do not put any part or accessory in a microwave, oven, air fryer or stovetop pot, or in boiling water. This will damage the part.
• Never put any parts or accessories in the freezer.
• Never put the motor base in water. Wipe it with a damp, soapy sponge or cloth instead.

1. Switch off, unplug and wait for the blades to stop; detach the Cup and Easy-Twist Extractor Blade from the Motor Base.
2. Clean the Easy-Twist Extractor Blade immediately after use with soap and water, using a small brush or sponge to dislodge food without touching its sharp edges.
3. Leave every component of the Easy-Twist Extractor Blade in place; taking it apart can permanently damage it and cause leakage.
4. Dry the Easy-Twist Extractor Blade completely. Inspect its underside for cracks or breaks and replace the assembly if damaged or loose.
5. Rinse and briefly brush the Cups and To-Go Lids before washing them on the dishwasher top rack; never use the sanitise cycle because it can warp the plastic.
6. For stubborn food in the Cup, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, attach the blade, and blend for 20–30 seconds; unplug, then scrub and rinse.
7. Wipe the Motor Base with a sponge or cloth dampened with warm, soapy water, and use a small brush on the actuator area if needed. Do not remove base parts.

Next steps

1. Rinse and brush the Pitcher before washing it in the dishwasher, or hand-wash it with soap and water; avoid the sanitise cycle and scrub stuck food with a dish brush or sponge.
2. Inspect the Pitcher and its twisting threads for cracks, crazing or breaks. Replace a damaged Pitcher and do not use one that fails to align correctly with the blade. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
3. Hand-wash the Tamper with soap and water, using a dish brush or sponge for stuck food.
4. For stubborn Pitcher residue, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, secure the lid, and blend for 20–30 seconds; unplug and scrub away the loosened food.
5. Store the blender upright with nothing on top and the remaining accessories protected from damage; never leave the blade exposed on the Motor Base without a Cup attached.
6. Store the Pitcher upright with its lid secured and nothing on top of the lid.

1. Turn off and unplug the Motor Base, wait until all parts stop moving, then lift off the Pitcher.
2. Rinse the Pitcher and scrub away food with a dish brush before placing it in the dishwasher; avoid the sanitise cycle, whose high heat can warp plastic.
3. Alternatively, hand-wash the Pitcher with soap and water, using a brush or sponge on stuck food and keeping your hands away from the sharp blades.
4. Wipe the Motor Base with a sponge or cloth dampened with warm, soapy water; remove residue around the actuator with a small brush. Do not dismantle the base.
5. Inspect the Pitcher for cracks and other damage; replace a damaged Pitcher and never use one that does not fit the Motor Base correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
6. Store the Pitcher upright with its lid fitted and nothing on top; keep the other parts somewhere protected from damage.

1. Switch off, unplug and wait for the blades to stop; detach the Cup and Easy-Twist Extractor Blade from the Motor Base.
2. Clean the Easy-Twist Extractor Blade immediately after use with soap and water, using a small brush or sponge to dislodge food without touching its sharp edges.
3. Leave every component of the Easy-Twist Extractor Blade in place; taking it apart can permanently damage it and cause leakage.
4. Dry the Easy-Twist Extractor Blade completely. Inspect its underside for cracks or breaks and replace the assembly if damaged or loose. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Rinse and briefly brush the Cups and To-Go Lids before washing them on the dishwasher top rack; never use the sanitise cycle because it can warp the plastic.
6. For stubborn food in the Cup, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, attach the blade, and blend for 20–30 seconds; unplug, then scrub and rinse.
7. Wipe the Motor Base with a sponge or cloth dampened with warm, soapy water, and use a small brush on the actuator area if needed. Do not remove base parts.

Next steps

1. Rinse and brush the Pitcher before washing it in the dishwasher, or hand-wash it with soap and water; avoid the sanitise cycle and scrub stuck food with a dish brush or sponge.
2. Inspect the Pitcher and its twisting threads for cracks, crazing or breaks. Replace a damaged Pitcher and do not use one that fails to align correctly with the blade. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
3. Hand-wash the Tamper with soap and water, using a dish brush or sponge for stuck food.
4. For stubborn Pitcher residue, add water at 21°C or cooler to the MAX line and 1–2 drops of dish soap, secure the lid, and blend for 20–30 seconds; unplug and scrub away the loosened food.
5. Store the blender upright with nothing on top and the remaining accessories protected from damage; never leave the blade exposed on the Motor Base without a Cup attached.
6. Store the Pitcher upright with its lid secured and nothing on top of the lid.

1. Turn off and unplug the Motor Base, wait until all parts stop moving, then lift off the Pitcher.
2. Rinse the Pitcher and scrub away food with a dish brush before placing it in the dishwasher; avoid the sanitise cycle, whose high heat can warp plastic.
3. Alternatively, hand-wash the Pitcher with soap and water, using a brush or sponge on stuck food and keeping your hands away from the sharp blades.
4. Wipe the Motor Base with a sponge or cloth dampened with warm, soapy water; remove residue around the actuator with a small brush. Do not dismantle the base.
5. Inspect the Pitcher for cracks and other damage; replace a damaged Pitcher and never use one that does not fit the Motor Base correctly.
6. Store the Pitcher upright with its lid fitted and nothing on top; keep the other parts somewhere protected from damage.
7. Rinse and briefly brush the Cups and To-Go Lids, then wash them on the dishwasher top rack without the sanitise cycle.
8. For dried food, fill the Cup or Pitcher with room-temperature water at 21°C to the liquid MAX line and add 1–2 drops of dish soap. Attach the Extractor Blade to the Cup, or fit the Pitcher Lid with its Vented Lid Cap inserted, and blend on LOW for 20–30 seconds; unplug, then scrub and rinse.