1. Start cleaning. Power off and unplug the Motor Base, wait until the motor and all attachments stop, then detach the Cup, Blending Pitcher or Work Bowl.
2. Choose the vessel that needs a rinse blend. For the Cup, fill to the MAX line with room-temperature water and add one or two drops of dish soap; twist the Extractor Blade on tightly, mount the assembly on the Motor Base, plug in and blend for 20–30 seconds. For the Blending Pitcher, fill halfway with water and add one or two drops of dish soap; fit the Pitcher Lid, press the Lid Cap down firmly and twist it until locked, lock the Pitcher onto the Motor Base, plug in and blend for 20–30 seconds. Use the matching method for the vessel you are cleaning.
3. Stop before handling parts. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; continue with the component washing steps below.
4. Clean the Extractor Blade. Clean the Extractor Blade immediately after use with a small brush or sponge dampened with soapy water, keeping fingers away from the cutting edges.
5. Clean the base. Wipe the Motor Base with a warm sponge or dishcloth dampened with soapy water; use a small brush to clean its actuator system, then wipe dry with a clean cloth. NEVER submerge the motor base in water or cleaning liquid.
6. Choose a safe dishwasher cycle. Do not use the dishwasher heat or sanitise cycle for any part or accessory; the heat can warp parts.

Next steps

1. Wash the small accessories. Rinse or scrub debris from the Blade Adapter, Blade Attachments, Cups, Food Pusher and To-Go Lids before washing them in the dishwasher.
2. Wash the pitcher. Wash the Blending Pitcher and Pitcher Lid in the dishwasher, or hand-wash with soap and water without touching the sharp blades.
3. Wash the tamper. Hand-wash the Tamper with soap and water.
4. Wash the processor bowl. Remove all Blade Attachments, Discs and the Blade Adapter from the Work Bowl before washing the Work Bowl and Work Bowl Lid in the dishwasher or by hand with soap and water.
5. Store the system. Store NutriBullet Triple Prep System upright with nothing on top, with accessories safely covered. In the Work Bowl, fit the Blade Adapter onto the central shaft, then the Chopping Blade, Dough Blade and Slice/Shred Disc, and fit the Lid. Never store exposed Blades or Discs.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Air Fryer 6L; allow it to cool down thoroughly before removing or cleaning parts.
2. Wash the removable parts. Remove the Cooking Basket and 3-in-1 Tray. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and 3-in-1 Tray or any oven cleaner; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Air Fryer 6L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Air Fryer 6L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet XXL Digital Air Fryer 7L; allow it to cool down thoroughly before removing or cleaning parts.
2. Wash the removable parts. Remove the Cooking Basket and Crisping Tray. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and Crisping Tray; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet XXL Digital Air Fryer 7L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid.
6. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet XXL Digital Air Fryer 7L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet Twin Drawer Air Fryer; allow it to cool down thoroughly before removing or cleaning parts.
2. Wash the removable parts. Remove the Cooking Drawers and Crisping Trays. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Drawers and Crisping Trays; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet Twin Drawer Air Fryer base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid.
6. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet Twin Drawer Air Fryer and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Vision Air Fryer 8L; allow it to cool down thoroughly before removing or cleaning parts.
2. Wash the removable parts. Remove the Cooking Basket and 3-in-1 Tray. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket and 3-in-1 Tray or any oven cleaner; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Vision Air Fryer 8L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Vision Air Fryer 8L and store it in a safe, dry location.

1. Prepare the air fryer for washing. Turn off and unplug the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L; allow it to cool down thoroughly before removing or cleaning parts.
2. Wash the removable parts. Remove the Cooking Basket, Crisping Tray and Wire Rack. Wash them in warm, soapy water, or place them on the top rack of the dishwasher.
3. Avoid the sanitise cycle. Do not use a sanitise cycle: its high temperature can warp the plastic.
4. Use gentle cleaning tools. Do not use abrasive or metal cleaning tools on the Cooking Basket, Crisping Tray and Wire Rack; these can damage the non-stick coating.
5. Clean the base. Gently wipe residue off the inner wall of the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L base with a warm cotton cloth, then dry it with a dry cloth. Wipe the exterior with a damp cloth. NEVER submerge the main unit in water or other liquid. Do not put the main unit in the dishwasher.
6. Remove food from the heating element. If food particles remain on the cooled heating element, brush them off with a soft-to-medium bristle brush.
7. Dry and store the air fryer. Dry every cleaned part thoroughly, reassemble the NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L and store it in a safe, dry location.

1. Take the blender apart. Unplug the NutriBullet Immersion Blender 800W and wait until the motor, blade or whisk has completely stopped. Lift the stopped blending arm or whisk out of its mixing vessel, then detach the motor body from the blending arm, whisk or chopping bowl. Separate the whisk from its holder, or the S-blade and lid from the chopping bowl; leave the blending arm as one piece. Empty the mixing vessel or chopping bowl.
2. Wash the removable attachments. Wash the chopping bowl, whisk, blending cup and chopping blade with warm, soapy water, or place those parts in the dishwasher.
3. Clean the geared attachments. Hand-wash the whisk holder, chopping bowl lid and blending arm with warm, soapy water. Do not soak these three parts or put them in the dishwasher, because water can damage the internal gears.
4. Avoid metal sponges. Do not use a metal sponge to clean any parts; it can scratch or damage them.
5. Clear the blade and whisk. Clean the blade and whisk after every use, handling the sharp blade carefully; remove all traces of food so residue does not build up and reduce blending performance.
6. Clean the motor unit. Wipe the motor unit with a damp cloth only. NEVER submerge the main unit in water or another liquid.
7. Dry and store attachments. Let all parts dry thoroughly, then store the NutriBullet Immersion Blender 800W and attachments in a safe, dry place where they cannot be damaged or cause harm.

1. Prepare the cooker for cleaning. Remove cooked food from the Cooking Pot or Steaming Basket for serving or storage, and discard leftover scraps. Turn off and unplug the NutriBullet EveryGrain Cooker and let it cool completely before cleaning the heating plate.
2. Remove stuck-on food. Soak the Cooking Pot with water before cleaning if food sticks. For hard residue, apply dishwashing liquid directly to it, leave it for a few minutes, then soak the area in water.
3. Wash the accessories. Wash the Steaming Basket, Spatula and Measuring Scoop in warm, soapy water, or put these accessories in the dishwasher.
4. Protect the Cooking Pot. Always hand-wash the Cooking Pot with warm, soapy water to protect its non-stick coating. Do not put the Cooking Pot in the dishwasher.
5. Clean the heating plate. After the heating plate is completely cool, wipe it with a clean, damp cloth. Clean the Cooking Pot, used Steaming Basket and heating plate after every use to prevent buildup.

Next steps

1. Clean the lid and water collection parts. After every use, wipe the Sealing Panel and Condensation Collector thoroughly with a damp cloth or sponge and warm, soapy water. Remove the Steam Vent plug and rinse it in warm water; wipe inside the Steam Vent with a damp cloth.
2. Avoid steel wool. Do not use steel wool pads or balls on the Cooking Pot, Sealing Panel or any other cooker part.
3. Clean the Cooker Base. Wipe the Cooker Base with a damp cloth only. NEVER submerge the main unit in water or another liquid.
4. Store the cooker. Once the NutriBullet EveryGrain Cooker is off, unplugged and at room temperature, store it upright in a cool, dry place with its accessories and power cord.

1. Prepare the processor for cleaning. Turn off and unplug the NutriBullet Food Processor, then detach the blades and other attachments from the Motor Base before cleaning.
2. Wash the removable parts. Wash the Blade Adaptor, Chopping Blade, Dough Blade, Slice/Shred Discs, Spiralizer Disc, Work Bowl, Work Bowl Lid and Dual-Size Food Pusher by hand in warm, soapy water or on the dishwasher top rack.
3. Handle the blades. Handle each sharp blade attachment carefully while removing and cleaning it.
4. Avoid damaging cycles and scrubbers. Do not use a sanitise cycle, steel wool pads or balls, or other hard materials that can warp or scratch the Work Bowl, lid and other parts.
5. Clean the Motor Base. Keep the Motor Base unplugged. Wipe it with a sponge or dishcloth dampened with warm, soapy water; use a small brush on the actuator system area if food remains. Wipe leakage residue with a damp sponge and warm water. NEVER submerge the motor base in water. Never remove pieces from the base.
6. Store the blade attachments. With the processor off and unplugged, fit the Blade Adaptor over the centre shaft. Lower the Chopping Blade onto the shaft, then the Dough Blade above it. Place the disc attachments on the adaptor above the blades, in their lower storage position; the disc and adaptor lines should not align.
7. Choose a storage arrangement. Store either both Slice/Shred Discs with the Chopping Blade and Dough Blade, or one Slice/Shred Disc and the Spiralizer Disc with those blades. Put the Spiralizer Disc in last, aligning its notches with the upper tabs and turning its FRONT marking towards the front.
8. Close the stored processor. Lock the Work Bowl Lid onto the bowl with the Dual-Size Pusher nested in the Feed Chute, then wrap the power cord under the Motor Base.

1. Prepare Chill for washing. Unplug the NutriBullet Chill and wait until all parts stop moving before handling them. Handle the sharp blade by its shaft, keeping fingers away from its edge.
2. Separate and wash the detachable parts. Remove the Blade from the Blade Block before placing the Pint Cup, lid, Blade, Blade Block and Shaft on the dishwasher top rack. These parts can also be washed by hand with warm, soapy water.
3. Hand-wash the Blade Block. Use a sponge and dish soap to gently clean the circular opening in the Blade Block and around the Blade Shaft.
4. Clean the Motor Base. Wipe the Motor Base with a damp sponge or cloth and mild, soapy water. Use a cleaning brush around the top where the Pint Cup attaches if needed. Keep liquid away from the drive shaft and centre hole. NEVER submerge the motor base in water. Do not put the motor base in the dishwasher.
5. Store the blade safely. Make sure all parts are clean and dry. Store the NutriBullet Chill unplugged, with the Blade Cover fitted to the blade or the blade attached to the Pint Cup. Never leave an exposed Blade Block on the Motor Base.

1. Prepare the processor for cleaning. Turn off and unplug the NutriBullet Limitless Food Processor before detaching blades and accessories from the Motor Base.
2. Wash the removable parts. Hand-wash the Blade Adaptor, Chopping Blade, Reversible Slice/Shred Disc, Work Bowl, lid, Food Pusher, Endless Chute and Slinger Disc with warm, soapy water, or place them on the top dishwasher rack. Keep the dishwasher temperature at or below 82°C.
3. Avoid damaging cycles and scrubbers. Do not use heat or sanitise cycles, steel wool pads or balls, or other hard materials that could warp or scratch the parts.
4. Handle sharp attachments. Handle blades and discs with care while washing; keep them covered by the appropriate lid or cover when stored, never exposed.
5. Clean the Motor Base. With the base unplugged, wipe it using a sponge or dishcloth dampened with warm, soapy water. Scrub the actuator area with a small brush if necessary and wipe leakage residue with a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove any base pieces or put the base in the dishwasher.
6. Store the blades in the bowl. With the processor off and unplugged, lower the Chopping Blade onto the Blade Adaptor, then lower the Reversible Slice/Shred Disc onto the adaptor above it.
7. Finish storing the processor. Lock the Work Bowl Lid in place with the Food Pusher nested in the Feed Chute. Store the Endless Chute and Slinger Disc separately.

Never submerge the Motor Base in water or any other liquid.

1. Prepare Baby for cleaning. Unplug the NutriBullet Baby and wait until every moving part has stopped before removing the cup or Batchbowl and blade.
2. Loosen dried food in a cup. Fill the cup halfway with soapy water and twist on the blade. Place the cup-and-blade assembly onto the Motor Base, reconnect power, then press down and twist clockwise to blend for 10–20 seconds. Twist anticlockwise to stop, unplug and wait for the blade to stop. Remove the assembly and untwist the blade; empty the water, lightly scrub away remaining debris and rinse.
3. Wash the cups and Batchbowl. Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse.
4. Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
5. Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.

1. Prepare Steam + Blend for cleaning. Turn off and unplug the NutriBullet Baby Steam + Blend, then let it cool completely before handling or cleaning parts.
2. Open and separate the used bowl. Allow at least ten minutes for cooling and wait until the appliance is completely cool and all moving parts have stopped. With the appliance unplugged, turn the Work Bowl clockwise off the base. Open the lid and turn its circular bottom grip anticlockwise to separate the lid into two pieces; remove trapped food or water and dry those pieces fully. Lift the Blending Blade vertically out by a non-sharp area using a mitt.
3. Empty and clean the reservoir and blade stem. Remove food from the Work Bowl, untwist the Water Reservoir Cap and discard remaining water. Use a cloth or soft-bristled brush to clear food from the bowl and inside the lid. Clean inside the Blade Stem to remove food or water, then dry it completely.
4. Rinse food away. Rinse the Work Bowl, Work Bowl Lid and Blending Blade under running water after use, holding the sharp blade by a non-sharp area. Clean the blade after every blend so food and mineral residue cannot build up.
5. Wash the bowl and lid. Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasher.
6. Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.

Next steps

1. Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use. NEVER submerge the motor base in water.
2. Check whether descaling is needed. Descale every four weeks, or sooner if limescale appears. Allow the appliance to cool completely after a steam cycle before starting.
3. Descale the Water Reservoir. Empty the Water Reservoir. Use a suitable chemical-free descaler or pour in 240 mL white vinegar. Leave the vinegar for at least 30 minutes, up to 24 hours according to the buildup, then discard it. Rinse with cool water and empty the loosened scale into the sink.
4. Finish descaling. After descaling, boil fresh water several times and discard it to remove remaining scale or vinegar. For the final cleaning cycle, let the appliance cool, fill the Water Reservoir to the 25-minute line and lock its cap clockwise. Fit the Blending Blade vertically onto the Blade Holder, lock the Work Bowl Lid clockwise and lock the bowl anticlockwise onto the base. Connect power, select Steam with the Setting Dial and press Power. The indicator flashes blue while steaming; five beeps mark completion. After the cycle, unplug and cool completely; lift the sharp blade vertically out using a mitt, then discard water from the Work Bowl and reservoir. Repeat descaling if limescale remains.
5. Store Steam + Blend. Unplug the appliance when it will not be used for a while. Keep all pieces together and store the assembled NutriBullet Baby Steam + Blend in a safe, dry, cool place.

1. Prepare Kitchen Express for cleaning. Power off and unplug the Magic Bullet Kitchen Express 250W and wait for every moving part to stop. Turn the Work Bowl anticlockwise to remove it from the Motor Base, then turn its lid anticlockwise and lift it off. Carefully lift out the Chopping Blade before pouring food or scraps from the bowl. If you used the Slice/Shred Disc, remove it using the two larger finger holes before emptying the bowl. If you used the Blending Cup, turn it anticlockwise to remove it, stand it upright with the Cross Blade on top, unscrew the blade and empty the contents.
2. Wash the removable parts. Place every removable component on the dishwasher top rack, or hand-wash with warm, soapy water and rinse. Keep the Motor Base out of the dishwasher and never use a sanitise cycle, which can warp the cups and Work Bowl.
3. Handle the sharp attachments. Handle the blades carefully; pick up each blade disc using its two larger finger holes.
4. Clean the Motor Base. With the Motor Base unplugged, wipe it with a sponge or damp cloth. If dried food remains at the actuator system, scrub that area with a small brush until clear. NEVER submerge the motor base in water or other liquid. Do not remove pieces from the base.
5. Store Kitchen Express. Store all pieces together in a safe place where they cannot be damaged or cause harm.

1. Prepare the air fryer for cleaning. Turn off and unplug the Magic Bullet Air Fryer 2.5L after use. Before removing the Fry Pot, check the timer reads 0, the orange indicator light is off and the heating element is completely cool.
2. Remove food scraps. Pull the Fry Pot out of the Base and inspect inside for food scraps. Lift the Crisping Tray by its centre handle and clear remaining scraps from both parts, taking care around the tray’s sharp edges.
3. Wash the Fry Pot and Crisping Tray. Rinse the Fry Pot and Crisping Tray with hot, soapy water. Clean them after each use, as soon as the heating element has cooled, so food does not dry onto the surfaces.
4. Clean the base. Wipe the exterior of the Air Fryer Base with a clean, damp cloth. NEVER submerge the main unit in water or another liquid.
5. Store the air fryer. Store all Magic Bullet Air Fryer 2.5L parts together in a safe place where they cannot be damaged or cause harm.

1. Prepare for cleaning. Power off and unplug the motor base; wait until the motor has completely stopped before removing the cup or handling the blender.
2. Detach the cup and blade. Detach the cup and Rapid Extractor Blade from the motor base, then separate them to clean the individual components.
3. Fill the cup. Fill the cup to the MAX line with room-temperature water and add 1–2 drops of dish soap, then twist the Rapid Extractor Blade on tightly.
4. Run the rinse blend. Reconnect power, invert the sealed cup and blade assembly onto the motor base and twist clockwise until it clicks and the control panel lights; use the solid-circle blend control for 20–30 seconds to loosen residue.
5. Finish removing the food. Stop the motor, unplug the base and wait for all movement to stop before removing the assembly; scrub the loosened residue away with soap and water.
6. Choose a safe dishwasher setting. Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.
7. Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.

Next steps

1. Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
2. Take apart the processor for washing. With power disconnected and the blade or disc stopped, turn the Work Bowl Lid anticlockwise and lift it off, then turn the Work Bowl and Processor Base anticlockwise and lift them from the Motor Base.
3. Remove the blade or disc. Hold the plastic centre hub of the Chopping Blade or Slice/Shred Disc and pull upwards; never tip the Work Bowl to drop a sharp part into your hand.
4. Remove the Work Bowl from the Processor Base. Hold the Processor Base from below with one hand and the Work Bowl handle with the other, turn the bowl anticlockwise and carefully lift it off the Processor Base and Blade Adapter.
5. Remove residue from processor blades and discs. Immerse only the removed Blades or Discs in room-temperature water with 1–2 drops of dish soap, wait 20–30 seconds, then carefully scrub away the loosened debris.
6. Wash the processor parts. Put the Blades, Discs, Work Bowl and Work Bowl Lid on the dishwasher top rack only; never use the heat or sanitise cycle.
7. Hand-wash the processor base and adapter. Keep the Processor Base and Blade Adapter out of the dishwasher and wash them by hand; alternatively hand-wash all Processor Attachment parts with a sponge or cloth, soap and water.

Next steps

1. Take apart the grinder for cleaning. After each use, unplug the Motor Base, wait for the blades to stop, disengage the Coffee & Dry Spice Grinder Attachment and separate the Grinding Cup from the Grinder Blade, handling the sharp blade carefully.
2. Wash the grinder parts. Wash the Grinding Cup and Grinder Blade on the dishwasher top rack only, without the heat or sanitise cycle; alternatively hand-wash them with a sponge or cloth, soap and water.
3. Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
4. Store the blender. Store the blender upright with nothing placed on top and keep accessories in a safe place; never leave an exposed Rapid Extractor Blade on the motor base without a cup attached.
5. Store the processor blade and disc safely. Fit the Blade Adapter onto the Work Bowl centre shaft, followed by the Chopping Blade; hold the Disc by its centre knob and lower it to the lower storage position about halfway down the adapter shaft without aligning their marks, then attach the Work Bowl Lid.
6. Cover the sharp parts. Keep Blades and Discs covered inside the Processor Attachment with the Work Bowl Lid attached; never leave a Blade or Disc exposed on the Motor Base.
7. Store the grinder. Store the blender and Coffee & Dry Spice Grinder Attachment in a dry, cool, clean place with the power cord safely tucked away; do not use the grinder as a food-storage container or leave an exposed Blade Assembly on the Motor Base.