• For NutriBullet Select 1200 / 2.0 Select 1200, for the cup, screw the easy-twist extractor blade on tightly and lock the inverted assembly clockwise onto the base.
• For the pitcher, screw the blade into its bottom and twist the pitcher onto the base until it clicks.

1. For NutriBullet Select 1200 / 2.0 Select 1200, secure the pitcher lid and vented cap when using the pitcher, plug in, press POWER, then select LOW, HIGH or EXTRACT.
2. The selected control should light and blending should begin, otherwise switch off and recheck the fitted vessel.

• EXTRACT on NutriBullet Select 1200 / 2.0 Select 1200 stops at the end of its program, and cup speed settings stop automatically after 60 seconds.
• Pitcher speed settings run until paused or stopped.
• PULSE runs only while its button is held.
• Releasing it stops the blades.
• Do not keep the motor running continuously for more than one minute.
• If the motor stops unexpectedly before the selected cycle ends, unplug the base and allow at least 15 minutes to cool before checking the fit and ingredients and trying again.
• If it still fails, leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

1. For NutriBullet Select 1200 / 2.0 Select 1200, press POWER, wait for the blade to stop, remove the lid and use the tamper to move stuck food.
2. If ingredients keep sticking, add a little more liquid so they can circulate, keeping solids and liquids below their separate MAX marks.

• With NutriBullet Select 1200 / 2.0 Select 1200 switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• Never run NutriBullet Select 1200 / 2.0 Select 1200 with an empty cup or use it as an ice crusher without liquid.
• Switch off and unplug, wait for the blade to stop and lift off the cup-and-blade assembly.
• Open only when the cup is completely cool.
• Reduce the hard-ingredient load and add liquid below MAX, then tighten the blade and lock the cup back onto the base.
• Select the required control after reconnecting power.
• If the load still stalls, stop and complete the motor-cooling check.

• Switch NutriBullet Select 1200 / 2.0 Select 1200 off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Select 1200 / 2.0 Select 1200, keep single-serve Cup use within four EXTRACT programs or 180 seconds of continuous running in a six-minute period. The same limit applies to its Pitcher.
• If the blender shuts down after repeated use, switch it off and unplug it.
• Allow at least 15 minutes for the Motor Base to cool before another attempt.
• If the Cup feels warm, leave it closed until completely cool before opening or changing the load.
• Refit the properly filled vessel securely before reconnecting power.

What if it still will not start? Leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Select 1000 / Select 1000 with pitcher, for NB07200-1007DG cup use, tighten the extractor blade onto the cup, plug in and press POWER, then twist the inverted cup clockwise onto the base and choose a speed or EXTRACT.
• Blending should start with the selected control lit, otherwise disconnect power and reseat the cup.

• EXTRACT on NutriBullet Select 1000 / Select 1000 with pitcher stops at the end of its program, and cup speed settings stop automatically after 60 seconds.
• PULSE runs only while its button is held.
• Releasing it stops the blades.
• Do not keep the motor running continuously for more than one minute.
• If the motor stops unexpectedly before the selected cycle ends, unplug the base and allow at least 15 minutes to cool before checking the fit and ingredients and trying again.
• If it still fails, leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

1. For NutriBullet Select 1000 / Select 1000 with pitcher, press POWER or the selected speed to stop, then wait for the blade to become still before unlocking the cup anticlockwise.
2. If movement continues, switch off at the power supply only when safe and stop the checks.

• With NutriBullet Select 1000 / Select 1000 with pitcher switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• Do not run NutriBullet Select 1000 / Select 1000 with pitcher with an empty cup or use the blades to crush hard ingredients without liquid.
• Switch off and unplug, wait for the blade to stop and remove the cup-and-blade assembly.
• For a cool cup, unscrew the blade, reduce the hard-ingredient load and add liquid within MAX.
• Securely screw the blade back on and lock the cup onto the base.
• If the corrected recipe still will not blend, stop and use the motor-cooling check.

• Switch NutriBullet Select 1000 / Select 1000 with pitcher off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Select 1000 / Select 1000 with pitcher, keep single-serve Cup use within four EXTRACT programs or 180 seconds of continuous running in a six-minute period.
• If the blender shuts down after repeated use, switch it off and unplug it.
• Allow at least 15 minutes for the Motor Base to cool before another attempt.
• If the Cup feels warm, leave it closed until completely cool before opening or changing the load.
• Refit the properly filled vessel securely before reconnecting power.

What if it still will not start? Leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Triple Prep System, choose the attachment first.
• Lock the cup clockwise until it clicks, or secure the pitcher lid and cap and lock the pitcher clockwise onto the base, then plug in and press POWER.

1. For NutriBullet Triple Prep System, fit the correct blade and adapter, lock the work bowl clockwise onto the base before locking its lid, align the lid arrows and insert the pusher.
2. The processor menu should illuminate when plugged in, otherwise disconnect power and rebuild in that order.

1. For NutriBullet Triple Prep System, cup blending is limited to one minute with no consecutive cycles.
2. Let the contents settle for 10-15 minutes before another cycle, and do not treat that settling time as a motor-overheat reset.

• For NutriBullet Triple Prep System, four dashes mean the powered base has no locked attachment.
• Refit the correct attachment, and if its menu still does not appear, stop and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

1. For NutriBullet Triple Prep System, the display dims after a program or speed ends or after 60 seconds idle, with Power and Timer still lit.
2. Tap a program or speed to wake it, and if the expected controls do not return, recheck the attachment.

• Overloading NutriBullet Triple Prep System can engage its thermal breaker.
• Unplug the motor base and leave it to cool for an hour before trying again.
• After all movement stops, remove the fitted attachment and reduce excess ingredients.
• Use enough liquid with ice or frozen ingredients.
• Refit the attachment securely before restarting.
• If the motor still will not run, take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• With NutriBullet Triple Prep System switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• Switch NutriBullet Triple Prep System off, unplug and wait until the blade stops.
• Remove the cool fitted vessel and reduce excess contents before refitting it.
• Do not grind dry grains, cereal or coffee with its blending blades.
• For blending, use sufficient liquid with ice or frozen ingredients and stay below MAX.
• If the motor has overheated, use the model’s thermal-breaker wait before attempting another blend.

• An overloaded Feed Chute or excessive Food Pusher pressure can overheat the motor of NutriBullet Triple Prep System.
• Turn off, unplug and wait for all blades or discs to stop.
• Unlock the Work Bowl Lid, reduce the food load and remove any stuck food with a spatula while the processor is disconnected.
• Refit the Work Bowl on the base before locking its Lid with the arrows aligned.
• Start the processor before adding more food.
• Allow food to move down the Feed Chute naturally and use only gentle pressure with the supplied Food Pusher.
• If the motor has shut down, complete the thermal-breaker cooling check before restarting.

• Locking an attachment onto NutriBullet Triple Prep System illuminates the matching menu but does not start processing.
• For a Cup, choose Frozen Drinks, Smoothie, Dressing or an available speed.
• For a Pitcher, select its displayed program or speed.
• With the processor Work Bowl and Lid locked, select Chop, Dip or an available speed, or hold Pulse for manual chopping.
• Release Pulse to stop its burst.
• If the menu shows four dashes instead of attachment controls, turn off and refit the attachment using the assembly checks.

• Switch NutriBullet Triple Prep System off, unplug it and wait until the blade or disc has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• If using a warm sealed Cup, leave it closed and on the base for at least 30 minutes, and longer until completely cool, before removing or opening it. Let any warm contents in other attachments cool before handling them.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• For the Work Bowl, turn its Lid anticlockwise to unlock and remove it first. Then turn the Work Bowl anticlockwise and lift it off the Motor Base. Lift out the blade or disc by its plastic centre before emptying the bowl.
• Remove the object while keeping clear of the blade or disc’s sharp edges. Inspect the vessel and cutting attachment; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Blender Combo 1200, for NBF07500-1210DG, tighten the extractor blade onto a cup and lock the inverted assembly clockwise onto the base, or lock the pitcher clockwise with its lid and vented cap fitted.
• A secure vessel should click into place, otherwise reseat it with power disconnected.

• On NutriBullet Blender Combo 1200, EXTRACT stops automatically when its program finishes, and cup speeds switch off after 60 seconds.
• Pressing the active speed or POWER also stops blending.
• PULSE runs only while you hold it.
• To start a new blend after the required rest, check the vessel is secure, press POWER and select the required speed or EXTRACT.
• Pitcher speeds continue until stopped, so watch the running time and keep each run within the guide’s one-minute limit.
• If the motor stops unexpectedly before the selected cycle ends, use the cooling check.

1. For NutriBullet Blender Combo 1200, if the motor stops unexpectedly, unplug and allow at least 15 minutes of cooling before another properly assembled attempt.
2. Keep sealed-cup runs within one minute instead of extending them to finish a thick blend.

• Stuck ingredients can stop circulating in the Pitcher of NutriBullet Blender Combo 1200.
• Power off, unplug and wait for the blade to stop before removing the Pitcher Lid.
• Use the supplied Tamper to dislodge the ingredients, keeping hands away from the blade.
• Remove the Tamper, refit the Lid and Vented Lid Cap, and check the Pitcher is seated before reconnecting.
• If food keeps sticking, add a little more liquid within MAX.
• If the blade still cannot move the mixture, stop and allow the motor to cool.

• With NutriBullet Blender Combo 1200 switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• An empty vessel, an ice-only load or too little liquid can prevent proper blending in NutriBullet Blender Combo 1200.
• Power off and unplug, wait for the blades to stop, then remove the cool cup-and-blade assembly or the pitcher.
• Open the cool vessel, remove excess ingredients below the correct MAX mark and add liquid.
• Do not use the blender as an ice crusher.
• Tighten the cup blade or refit the pitcher lid and cap, then secure the vessel on the base.
• Try a suitable blend after any required cooling rest.
• If food remains stuck, stop and use the ingredient-clearing check.

• Switch NutriBullet Blender Combo 1200 off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Blender Combo 1200, keep single-serve Cup use within four EXTRACT programs or 180 seconds of continuous running in a six-minute period.
• If the blender shuts down after repeated use, switch it off and unplug it.
• Allow at least 15 minutes for the Motor Base to cool before another attempt.
• If the Cup feels warm, leave it closed until completely cool before opening or changing the load.
• Refit the properly filled vessel securely before reconnecting power.

What if it still will not start? Leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

A flat line with BLEND or PULSE not working can mean the pitcher is not attached properly.

• Stop and disconnect power before reattaching the pitcher.
• Restore power and try BLEND or PULSE again.

If the flat line remains, leave the blender off and use the support option in this article.

• Use enough liquid to cover all solid ingredients for AUTO.
• For a smoothie, blend tougher ingredients with liquid in the first AUTO cycle, then add frozen ingredients for the second. Hard or fibrous ingredients may need two cycles.

If the motor is stopped or stalled, stop the attempt rather than repeatedly restarting.

• Switch NutriBullet SmartSense Blender NBF07600 — Australia off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• Remove the Pitcher from the Motor Base, then take off the Pitcher Lid. Leave the blade in the Pitcher.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade for cracks, chips or other damage. Replace a damaged removable vessel before use; for blade damage, leave the blender off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Smart Touch Blender Combo, lock the pitcher clockwise until it clicks, press its lid down firmly and lock the lid cap, then plug in and press POWER.
• The blending controls should appear, otherwise reseat the pitcher and lid.

• For NutriBullet Smart Touch Blender Combo, securely fit the blade and rotate the cup clockwise onto the base until it clicks.
• Select the available cup program or speed rather than looking for SOUPS, which is available only with the pitcher.

1. For NutriBullet Smart Touch Blender Combo, pressing an active program pauses the motor and timer, and pressing the same program resumes it.
2. If you paused a manual speed, selecting a manual speed resumes blending instead.

• For NutriBullet Smart Touch Blender Combo, flashing Power and Timer after a stop may mean overheating.
• Unplug, wait at least 15 minutes and reconnect, and if the display still flashes or the motor fails to run after correct assembly, stop the checks.

• With NutriBullet Smart Touch Blender Combo switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• An empty vessel, an ice-only load or too little liquid can prevent proper blending in NutriBullet Smart Touch Blender Combo.
• Power off and unplug, wait for the blades to stop, then remove the cool cup-and-blade assembly or the pitcher.
• Open the cool vessel, remove excess ingredients below the correct MAX mark and add liquid.
• Do not use the blender as an ice crusher.
• Tighten the cup blade or refit the pitcher lid and cap, then secure the vessel on the base.
• Try a suitable blend after any required cooling rest.
• If food remains stuck, stop and use the ingredient-clearing check.

• Stuck ingredients can stop circulating in the Pitcher of NutriBullet Smart Touch Blender Combo.
• Power off, unplug and wait for the blade to stop before removing the Pitcher Lid.
• Use the supplied Tamper to dislodge the ingredients, keeping hands away from the blade.
• Remove the Tamper, refit the Lid and Vented Lid Cap, and check the Pitcher is seated before reconnecting.
• If food keeps sticking, add a little more liquid within MAX.
• If the blade still cannot move the mixture, stop and allow the motor to cool.

• Cup speeds on NutriBullet Smart Touch Blender Combo stop after 60 seconds, while an intelligent program may pulse or change speed before its countdown ends.
• A completed program gives an audible alert and restores the main control panel.
• PULSE runs only while held.
• Release stops it.
• If the motor has stopped with Power and Timer flashing instead, use the overheating check.
• Do not extend a continuous blend beyond one minute.

• Switch NutriBullet Smart Touch Blender Combo off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• The Pitcher of NutriBullet Power Core Blender sits straight down on the Motor Base.
• With power disconnected, lift off the Pitcher and fit its Lid and Vented Lid Cap, aligning the rear loop opposite the spout with the handle.
• Lower the Pitcher onto the Motor Base with its studs aligned with the grooves.
• A click confirms it is seated.
• Plug in, press Power and select LOW.
• The blending mode lights should illuminate.
• If the Pitcher does not seat, lift it off and check the alignment again without forcing it.

1. For NutriBullet Power Core Blender, PULSE runs only while held, so releasing it is a normal stop.
2. Choose a manual speed for continuous blending, starting the pitcher on LOW and increasing after the mixture is smooth and steady.

1. For NutriBullet Power Core Blender, with power off and unplugged, wait for all movement to stop before opening the lid and loosening ingredients.
2. Remove the utensil completely before replacing the lid, and add more liquid if food keeps sticking.

• Do not run NutriBullet Power Core Blender for more than one minute or run consecutive cycles totalling more than one minute.
• If a blend stops early, switch off and unplug before checking its ingredient load.
• Follow the thermal-breaker cooling check below before another attempt.
• If normal operation does not return, leave the blender off.

• Too much ice or other ingredients can overheat NutriBullet Power Core Blender.
• Switch off and unplug the motor base.
• If its thermal breaker has stopped the motor, allow an hour to cool before retrying.
• With power disconnected and the blade still, remove the lid and reduce the load.
• Never try to grind dry grains, cereal or coffee.
• Refit the lid and vessel before switching on.
• If the motor still will not run, stop the checks.

• With NutriBullet Power Core Blender switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• An overloaded vessel or ice without enough liquid can stop the blade of NutriBullet Power Core Blender.
• Switch off, unplug and wait until the blade is still before removing the fitted vessel.
• Open it only when cool, remove excess ingredients below MAX and add enough liquid for blending.
• Never run the blender empty or crush ice by itself.
• Remove any utensil used to loosen food, then refit the correct Lid and vessel securely.
• If the motor has already overheated, use the hour-long thermal-breaker cooling check before trying the smaller blend.

• Switch NutriBullet Power Core Blender off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• Remove the Pitcher from the Motor Base, then take off the Pitcher Lid. Leave the fixed blade in the Pitcher.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Blender Combo 1000, tighten the extractor blade onto a cup and lock the inverted assembly clockwise onto the base, or lock the pitcher clockwise with its lid and vented cap fitted.
• A secure vessel should click into place, otherwise reseat it with power disconnected.

• On NutriBullet Blender Combo 1000, EXTRACT stops automatically when its program finishes, and cup speeds switch off after 60 seconds.
• Pressing the active speed or POWER also stops blending.
• PULSE runs only while you hold it.
• To start a new blend after the required rest, check the vessel is secure, press POWER and select the required speed or EXTRACT.
• Pitcher speeds continue until stopped, so watch the running time and keep each run within the guide’s one-minute limit.
• If the motor stops unexpectedly before the selected cycle ends, use the cooling check.

1. For NutriBullet Blender Combo 1000, if the motor stops unexpectedly, unplug and allow at least 15 minutes of cooling before another properly assembled attempt.
2. Keep sealed-cup runs within one minute instead of extending them to finish a thick blend.

• Stuck ingredients can stop circulating in the Pitcher of NutriBullet Blender Combo 1000.
• Power off, unplug and wait for the blade to stop before removing the Pitcher Lid.
• Use the supplied Tamper to dislodge the ingredients, keeping hands away from the blade.
• Remove the Tamper, refit the Lid and Vented Lid Cap, and check the Pitcher is seated before reconnecting.
• If food keeps sticking, add a little more liquid within MAX.
• If the blade still cannot move the mixture, stop and allow the motor to cool.

• With NutriBullet Blender Combo 1000 switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• An empty vessel, an ice-only load or too little liquid can prevent proper blending in NutriBullet Blender Combo 1000.
• Power off and unplug, wait for the blades to stop, then remove the cool cup-and-blade assembly or the pitcher.
• Open the cool vessel, remove excess ingredients below the correct MAX mark and add liquid.
• Do not use the blender as an ice crusher.
• Tighten the cup blade or refit the pitcher lid and cap, then secure the vessel on the base.
• Try a suitable blend after any required cooling rest.
• If food remains stuck, stop and use the ingredient-clearing check.

• Switch NutriBullet Blender Combo 1000 off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• Let any warm contents cool completely before opening the vessel.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Blender Combo 1000, keep single-serve Cup use within four EXTRACT programs or 180 seconds of continuous running in a six-minute period.
• If the blender shuts down after repeated use, switch it off and unplug it.
• Allow at least 15 minutes for the Motor Base to cool before another attempt.
• If the Cup feels warm, leave it closed until completely cool before opening or changing the load.
• Refit the properly filled vessel securely before reconnecting power.

What if it still will not start? Leave it off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For NutriBullet Power Core Blender Combo, fit the pitcher lid with its interlocking mechanism aligned at the handle, then twist the pitcher clockwise onto the base until it clicks.
• Plug in, press POWER and select LOW to begin, otherwise recheck the pitcher and lid locks.

1. For NutriBullet Power Core Blender Combo, PULSE runs only while held, so releasing it is a normal stop.
2. Choose a manual speed for continuous blending, starting the pitcher on LOW and increasing after the mixture is smooth and steady.

1. For NutriBullet Power Core Blender Combo, with power off and unplugged, wait for all movement to stop before opening the lid and loosening ingredients.
2. Remove the utensil completely before replacing the lid, and add more liquid if food keeps sticking.

• For NutriBullet Power Core Blender Combo, tighten the extractor blade onto the cup, invert it and twist it clockwise onto the base until it locks.
• The cup should be secure before selecting a control, otherwise remove and refit it rather than forcing the fit.

• Too much ice or other ingredients can overheat NutriBullet Power Core Blender Combo.
• Switch off and unplug the motor base.
• If its thermal breaker has stopped the motor, allow an hour to cool before retrying.
• With power disconnected and the blade still, remove the lid and reduce the load.
• Never try to grind dry grains, cereal or coffee.
• Refit the lid and vessel before switching on.
• If the motor still will not run, stop the checks.

• With NutriBullet Power Core Blender Combo switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• An overloaded vessel or ice without enough liquid can stop the blade of NutriBullet Power Core Blender Combo.
• Switch off, unplug and wait until the blade is still before removing the fitted vessel.
• Open it only when cool, remove excess ingredients below MAX and add enough liquid for blending.
• Never run the blender empty or crush ice by itself.
• Remove any utensil used to loosen food, then refit the correct Lid and vessel securely.
• If the motor has already overheated, use the hour-long thermal-breaker cooling check before trying the smaller blend.

• For the Cup on NutriBullet Power Core Blender Combo, press Power and then Smoothie to run its blending program.
• A finished program is a normal stop.
• Do not blend in a sealed Cup for longer than one minute or run consecutive cycles.
• Let the contents settle for at least 10–15 minutes before another cycle, and do not open a Cup that is still warm.
• With the Pitcher, pressing the selected speed again pauses it and turns off that setting light.
• Choose a speed to resume only after checking the load and fit.
• If Power remains lit after stopping, the blender is idle rather than disconnected.
• An early stop under a heavy load needs the thermal-breaker check.

• Switch NutriBullet Power Core Blender Combo off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• If using a warm sealed Cup, leave it closed and on the base for at least 30 minutes, and longer until completely cool, before removing or opening it. Let any warm contents in other attachments cool before handling them.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• For Magic Bullet Blender Combo, use the matching Combo cup and Cross Blade, lock the assembly onto the base and turn the dial right for HIGH.
• The motor should start only with a properly attached assembly, otherwise return the dial to HOME and refit it.

1. For Magic Bullet Blender Combo, too much ice can wedge in the blade and overheat the motor, so stop and correct the ingredient load.
2. If the thermal breaker has shut the motor off, unplug and cool the base for an hour before a properly assembled retry.

1. For Magic Bullet Blender Combo, inspect the disconnected Cross Blade for damage or a missing or damaged gasket.
2. Stop using the affected part and replace it if it is faulty, rather than forcing it to rotate during powered blending.

• With Magic Bullet Blender Combo switched off and unplugged, check that its ventilation openings are free of dust, lint and obstructions.
• Keep the base on a level surface with space for air circulation.
• Do not cover the openings with a cloth or other material.
• Clear the obstruction before the next use, and use the model’s cooling instructions if the motor has already stopped.

• Switch Magic Bullet Blender Combo off, unplug and wait until the blade stops.
• Remove the cool fitted vessel and reduce excess contents before refitting it.
• Do not grind dry grains, cereal or coffee with its blending blades.
• For blending, use sufficient liquid with ice or frozen ingredients and stay below MAX.
• If the motor has overheated, use the model’s thermal-breaker wait before attempting another blend.

• Never run the Cup of Magic Bullet Blender Combo empty.
• Return the Power Control Knob to HOME, unplug and wait for the Blade to stop before taking off the cup-and-blade assembly.
• Add a suitable recipe with enough liquid below MAX, secure the Cross Blade and lock the cup onto the Motor Base before selecting HIGH.
• If a correctly loaded and locked cup still will not run, return to HOME and use the assembly or cooling check.

• Before another blending cycle on Magic Bullet Blender Combo, return the Power Control Knob to HOME.
• Check that the cup-and-blade assembly or Pitcher remains locked onto the Motor Base, then select HIGH or LOW, or use PULSE from HOME.
• The next cycle should begin with the secured vessel.
• If it does not, return the knob to HOME and recheck the vessel lock.

• After two consecutive Cup blending cycles on Magic Bullet Blender Combo, wait 10–15 minutes before another cycle.
• Return the Power Control Knob to HOME and leave the appliance off during this rest.
• If the Cup feels warm, unplug and leave it in place for at least 30 minutes, and longer if needed until completely cool, before removing or opening it.
• If the motor has stopped from overheating, follow the separate one-hour thermal-breaker cooling check before trying again.

• Return the Power Control Knob of Magic Bullet Blender Combo to HOME, unplug and wait for the Blade to stop before removing the Pitcher.
• Check that the Blade is secured in the bottom of the Pitcher.
• If it is loose, turn the Blade counterclockwise to tighten it.
• Press the Pitcher Lid firmly down until it snaps into place, then insert the Vented Lid Cap and twist it closed.
• Place the Pitcher upright onto the Motor Base and turn it clockwise until it clicks.
• Reconnect power and select LOW or HIGH, beginning at LOW for hot ingredients.
• If the Pitcher still will not lock or the motor will not run, leave the knob at HOME and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

• Switch Magic Bullet Blender Combo off, unplug it and wait until the blade has stopped.
• Check for a spoon, packaging or another non-food object among the ingredients. Do not restart while an object is inside.
• If using a warm sealed Cup, leave it closed and on the base for at least 30 minutes, and longer until completely cool, before removing or opening it. Let any warm contents in other attachments cool before handling them.
• For the Cup, unlock and remove the Cup-and-Blade assembly from the Motor Base. Stand it upright, then unscrew the blade from the Cup.
• For the Pitcher, remove it from the Motor Base and take off its lid. Do not reach towards the blade.
• Remove the object while keeping clear of the blade’s sharp edges. Inspect the vessel and blade; replace any cracked, chipped or damaged part before reassembling.

What if the object cannot be removed safely, or the blade still will not move? Leave the appliance off and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).