Skip to main content

How can we help?

Which replacement parts fit my portable blender?

  • Updated

Compatible portable-blender replacements are the cup, lid or cover and any separately replaceable blade block listed for the exact appliance; a blade built into the motor base is not a separate screw-on replacement. Choose replacement parts listed for the exact blender model, then check the part codes and fitting steps below.

Order genuine parts through Australian accessories or New Zealand accessories. Switch the blender off, disconnect its charging cable and wait for the blades to stop before changing or cleaning parts.

NutriBullet Portable Blender / Portable Blender McLaren

For NB07400, use the Portable Blender’s matching 590 mL cup and Sip and Carry Lid; its blade assembly is part of the Motor Base.

Which pieces belong to the Portable Blender?
  • Identify the 590 mL cup by its measurement marks and alignment dot; match a replacement cup to the Portable Blender name and your NB07400 product code.
  • Identify the Sip and Carry Lid by its handle, release button and locking latch; use that complete lid arrangement when requesting a replacement.
  • Treat the blade assembly as part of the Motor Base; do not replace it with a screw-on blade from a corded personal blender.
  • Use the supplied USB-C charging cable with an approved general-purpose 100–240 V power supply rated 5 V, 2 A maximum; do not substitute a rapid or higher-wattage charger.
How do I check a replacement cup or lid fits correctly?
  1. Twist the cup onto the Motor Base until the two alignment dots line up; the cup must be locked before the motor can run. If it will not align, remove and refit it without defeating the interlock.
  2. Twist the lid onto the cup and put the latch upright in its locked position before blending; after the blade has stopped, lower the latch and press the lid button to open the drinking spout.
  3. Inspect the cup for cracks, cloudiness or other damage and the blade for bending or damage; stop using the affected part and arrange the correct replacement.
  4. Leave the rechargeable battery inside the Motor Base; it is not a replaceable part and the base must not be opened for a battery change.
How do I clean and store the new parts?
  1. Wash the cup and lid in warm soapy water and rinse, or place only those two parts in the dishwasher top rack with no heat or sanitise cycle.
  2. Gently rinse the blade area and wipe it with a damp sponge or cloth, keeping fingers away from the cutting edges. Do not hold the base under running water.
  3. For residue in an undamaged cup, add cold water and one drop of dish soap, close the lid and run one cleaning cycle; empty and rinse before using the cup again.
  4. Keep the USB-C port free of dust and foreign objects; connect only the appropriate charging plug and do not charge while the port or cable is wet.
  5. Store the blender upright with its cup attached to cover the blades, with nothing stacked on top; keep it away from extreme temperatures and use the guide’s 10–40°C storage range.

NutriBullet Flip Stainless

For Flip Stainless, listed replacements include stainless-cup codes ANBPB-VE179CDB, ANBPB-VE180CDB, ANBPB-VE181CDB or ANBPB-VE183CDB by finish, Tritan cup with sleeve ANBPB-VE166CDB, and Dual To-Go Lid ANBPB-VE151CDB. Buy a replacement 590 mL cup (Australia) or 590 mL cup (New Zealand). Buy a replacement 590 mL cup (Australia) or 590 mL cup (New Zealand). Buy a replacement 590 mL cup (Australia) or 590 mL cup (New Zealand). Buy a replacement 590 mL cup (Australia) or 590 mL cup (New Zealand). Buy a replacement NutriBullet Flip Dual To-Go Lid with Handle (Australia) or NutriBullet Flip Dual To-Go Lid with Handle (New Zealand).

Which replacement codes fit Flip Stainless?
How do I fit and use the Flip pieces?
  1. Check the cup, combined Motor Base, Blade and Lid, To-Go Lid, straw, cleaning brush, blade cover, USB-C cable and power supply when identifying the required piece.
  2. Twist the combined motor/blade/lid assembly onto the cup, then snap its Flip-Top Lid closed; wake the blender and check for a fully white light ring. A flashing yellow ring calls for tightening the cup until it is secure.
  3. To use the separate To-Go Lid, remove the combined motor/blade/lid assembly, clean and dry it, attach its Blade Cover, then twist the To-Go Lid onto the cup.
  4. For sipping, unsnap the front flap and fold it back until it clips at the opposite side; for the straw opening, keep the sipping flap closed and slide the centre tab backwards.
  5. Keep the cup upright when using the To-Go Lid because it is not leak-proof; use the straw only after the motor has stopped.
  6. Use only the supplied charging cable and power supply; do not use a rapid charger, voltage converter or adapter, and do not attempt to replace the internal batteries.
How do I protect the Flip replacement parts?
  1. Before cleaning, unplug the charging cable and leave the blender undisturbed for 90 seconds so it shuts down; check that the blades have completely stopped.
  2. For automatic cleaning, rinse the cup, half-fill it with water and a drop of dish soap, then run a cycle while flipping and shaking the blender. For stubborn residue, soak each end briefly before the cycle.
  3. Empty through the opened Flip-Top Lid after the cleaning cycle; run a second cycle with fresh water only and dry the assembly upright with the Flip-Top Lid open.
  4. For hand-cleaning the blade, angle it downward and rinse only the blade area while covering the USB-C port with a finger or thumb. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire motor/blade/lid assembly.
  5. For the drinking spout, face the blade upward and gently rinse the sip hole while protecting the USB-C port; use the supplied brush under the blades and in the sip hole, vent hole and straw.
  6. Wash the cup with soap and water; only the cup and To-Go Lid may go in the dishwasher, on the top rack. Keep the motor/blade/lid assembly out of the dishwasher.
  7. Wipe the motor/blade/lid assembly and USB-C port dry with a clean cloth; charge only after the port is completely dry.
  8. Store in a dry, temperature-controlled place with the cup or blade cover attached over the blade, and do not stack objects on the blender.

NutriBullet Flex Portable / Flex Portable McLaren

Flex Blade Block BDM-BA035CDB fits any Flex Portable Blender; cup-and-lid kits ANBPBCL22BBCDB, ANBPBCL22CDB, ANBPBCL22EGCDB and ANBPBCL22WCCDB need the matching colour and full product code.

Which replacement codes fit Flex Portable?
  • Choose BDM-BA035CDB for the Flex Blade Block; its listing covers any NutriBullet Flex Portable Blender.
  • For a Flex cup-and-lid kit, compare ANBPBCL22BBCDB, ANBPBCL22CDB, ANBPBCL22EGCDB and ANBPBCL22WCCDB; match the colour and full product code before ordering.
How do I fit the Flex Blade Block, cup and lid?
  1. Wash the Blending Cup, Blade Block and Sip Lid with Carry Loop before use; dry the Blade Block completely before attaching it to the cup.
  2. Insert the Blade Block blades-first through the cup’s bottom opening and twist until it reaches the built-in soft stop; do not force it farther.
  3. Twist the Sip Lid with Carry Loop onto the cup with the Sip Cap closed, then press the cap until it clicks and the seal engages.
  4. Place the Blade Block and cup on the Motor Base and gently twist clockwise until locked; if the pieces will not seat, remove them and check alignment instead of forcing the connection.
  5. Grip the Motor Base and cup to detach the cup after blending; do not pull using the Sip Lid or press downward while removing it.
  6. Lift the Carry Loop away from the Sip Cap to reach its release button; press to open, lightly press the opened cap back to hold it open, and lift it gently away from the cup to release that hold.
How do I clean and store the Flex pieces?
  1. Switch off and disconnect charging power before removing the Blade Block; turn the Blade Block clockwise to remove it and turn the Sip Lid anticlockwise.
  2. Hand-wash the Blade Block with warm soapy water and rinse; wash the cup and Sip Lid the same way, or place the cup and lid on the dishwasher top rack without the heat or sanitise cycle.
  3. Wipe food from the Motor Base with a damp cloth. Do not run the base under water and do not put the motor base in the dishwasher.
  4. Dry the lid and its gasket area fully before blending or storing; if the lid gasket moves during cleaning, remove excess moisture and gently guide it back into place.
  5. Store upright with the Blade Block secured to the cup and Sip Lid attached, keeping blades covered and nothing stacked on top.
  6. If packing for travel, cover and wrap the removed Blade Block so no cutting edge is exposed; check the carrier’s current blade and battery rules before packing.
Which other Flex pieces should I match?
  • Identify the 650 mL cup, Sip Lid with Carry Loop, detachable Blade Block, Motor Base and supplied USB-C cable separately before choosing a replacement.
  • Use the supplied USB-C cable and a charging supply certified for information technology equipment (ITE) rated 5 V, 2 A maximum; do not use a rapid or higher-wattage charger.
  • Leave the internal lithium-ion batteries inside the Motor Base; they are not replaceable and the base must not be opened for a battery change.
How do I check the Blade Block lock?
  1. When properly fitted, the light ring illuminates white clockwise and flashes twice; three orange flashes indicate an incomplete or misaligned Blade Block lock, so power off and refit it gently.

NutriBullet GO

Use the GO-specific 385 mL cup, cup cover or blade cover; its motor base and blade form one assembly.

Which pieces should I identify on GO?
  • Identify the 385 mL GO cup, cup cover, blade cover, combined motor base/blade assembly and USB type-C cable; order each against the GO name and product code.
  • Use the blade cover on the motor base when it is not attached to the cup; the cup cover is the separate piece used on the drink cup.
How do I check the GO cup fits?
  1. Hold the base from underneath, turn it upside down and twist it clockwise onto the cup rim until firmly fastened; keep fingers away from the blade.
  2. Wake the blender by holding the button for three seconds: a flashing blue light indicates a locked cup. If red and blue flash together, keep tightening the cup until it locks; never bypass the lock.
  3. After the motor and blade stop, turn the blender cup-side down and twist the base anticlockwise to detach it; screw on the blade cover before putting the motor base away.
  4. Replace a visibly damaged cup or other detachable part and do not attempt to repair the motor base or charging cable yourself.
How do I clean and store the GO pieces?
  1. Wash the cup and lid in warm soapy water and rinse, or put those pieces on the top rack of the dishwasher.
  2. Gently rinse the blade area and clean with a damp sponge or cloth without touching the cutting edges. Do not run the whole base under water or place the motor base's blade assembly in the dishwasher.
  3. Store all parts together in a safe place, with the blades covered by the cup or Blade Cap and the power light off.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: NutriBullet Portable Blender / Portable Blender McLaren user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Flip Stainless user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Flex Portable / Flex Portable McLaren user guide (PDF)

The full steps for this model are in its user guide: NutriBullet GO user guide (PDF)

Related articles

Contact us