1. Start cleaning. Power off and unplug the Motor Base, wait until the motor and all attachments stop, then detach the Cup, Blending Pitcher or Work Bowl.
2. Add water to the vessel with stuck food. For a Cup, fill to the MAX line with room-temperature water and add one or two drops of dish soap. For the Blending Pitcher, fill halfway with water and add one or two drops of dish soap.
3. Run the cleaning blend for that vessel. For a Cup, twist the Extractor Blade tightly onto it and mount the assembly on the Motor Base. For the Blending Pitcher, fit the Pitcher Lid, press the Lid Cap down firmly and twist it until locked and Lid Cap securely and lock the Pitcher onto the Motor Base. Plug in and blend for 20–30 seconds.
4. Stop and detach the vessel. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; then continue with the washing steps below.
5. Clean the Extractor Blade. Clean the Extractor Blade immediately after use with a small brush or sponge dampened with soapy water, keeping fingers away from the cutting edges.
6. Clean the base. Wipe the Motor Base with a warm sponge or dishcloth dampened with soapy water; use a small brush to clean its actuator system, then wipe dry with a clean cloth. NEVER submerge the motor base in water or cleaning liquid.

Next steps

1. Wash the pitcher. Wash the Blending Pitcher and Pitcher Lid in the dishwasher, or hand-wash with soap and water without touching the sharp blades.
2. Wash the tamper. Hand-wash the Tamper with soap and water.
3. Wash the processor bowl. Remove all Blade Attachments, Discs and the Blade Adapter from the Work Bowl before washing the Work Bowl and Work Bowl Lid in the dishwasher or by hand with soap and water.
4. Wash the small accessories. Rinse or scrub debris from the Blade Adapter, Blade Attachments, Cups, Food Pusher and To-Go Lids before washing them in the dishwasher.
5. Store the system. Store NutriBullet Triple Prep System upright with nothing on top, with accessories safely covered. In the Work Bowl, fit the Blade Adapter onto the central shaft, then the Chopping Blade, Dough Blade and Slice/Shred Disc, and fit the Lid. Never store exposed Blades or Discs.

1. Take the blender apart for washing. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Loosen dried ingredients. Fill the Cup or Pitcher to its MAX line with room-temperature water at 21°C or below, and add one or two drops of dish soap.
3. Run the cleaning blend. For a Cup, twist on the Easy-Twist Extractor Blade and mount the assembly on the Motor Base; for the Pitcher, fit the Lid and mount it on the base. Plug in and blend for 20–30 seconds.
4. Stop and detach the vessel. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; then continue with the washing steps below.
5. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
6. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.

Next steps

1. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
2. Wash the cups and To-Go Lids. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.
3. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
4. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.
5. Dry and inspect the blade. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
6. Store the clean parts. Store the Pitcher upright with its Lid secured and nothing on top. Keep other pieces somewhere safe from damage and never leave the Easy-Twist Extractor Blade exposed on the Motor Base without a Cup or Pitcher covering it.

1. Wash the Pitcher. Wash the SmartSense Blender Pitcher in the dishwasher; keep the Tamper and Motor Base out of the dishwasher.
2. Wash the tamper and wipe the base. Hand-wash the Tamper with soap and water. Wipe the Motor Base with a damp cloth. NEVER submerge the motor base in water.

1. Take the blender apart for washing. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
3. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.
4. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
5. Wash the cups and To-Go Lids. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.

Next steps

1. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
2. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.
3. Dry and inspect the blade. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender.
4. Store the clean parts. Store the Pitcher upright with its Lid secured and nothing on top. Keep other pieces somewhere safe from damage and never leave the Easy-Twist Extractor Blade exposed on the Motor Base without a Cup or Pitcher covering it.

1. Begin cleaning. Turn off and unplug the blender; wait until all parts stop, then remove the Pitcher from the Motor Base.
2. Clean the base. Wipe the outside of the unplugged Motor Base with a clean cloth. NEVER submerge the motor base in water. Do not take the motor base apart.
3. Clear the actuator area. Use a small brush to clear residue around the actuator system while the Motor Base is unplugged.
4. Wash the pitcher. Rinse and briefly scrub the Pitcher with a dish brush before dishwasher washing, or hand-wash with soap and water. Use a brush or sponge on stuck food and keep clear of the sharp blades.
5. Wash the lid and cap. Before first use, rinse detachable parts and hand-wash with warm soapy water or wash in the dishwasher. Keep the Motor Base out of the dishwasher.
6. Store the clean pitcher. Store the Pitcher upright with its Lid secured and nothing on top; keep remaining parts somewhere safe from damage.

1. Take the blender apart for washing. Power off, unplug and wait until every part stops moving, then detach the cup and Easy-Twist Extractor Blade assembly or pitcher from the Motor Base.
2. Loosen dried ingredients. Fill the Cup or Pitcher to its MAX line with room-temperature water at 21°C or below, and add one or two drops of dish soap.
3. Run the cleaning blend. For a Cup, twist on the Easy-Twist Extractor Blade and mount the assembly on the Motor Base; for the Pitcher, fit the Lid and mount it on the base. Plug in and blend for 20–30 seconds.
4. Stop and detach the vessel. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; then continue with the washing steps below.
5. Clean the Motor Base. Wipe the unplugged Motor Base with a sponge or cloth dampened with warm soapy water; for leaked food on its surface, use a damp sponge and warm water. NEVER submerge the motor base in water. Do not remove pieces from the motor base.
6. Clean around the actuator. Use a small brush to clear food around the actuator system only while the Motor Base is unplugged.

Next steps

1. Clean the blade. Hand-wash the Easy-Twist Extractor Blade with soap and water immediately after use. Target trapped food with a small brush or sponge, keeping clear of sharp edges.
2. Wash the cups and To-Go Lids. Rinse and briefly scrub the Cups and To-Go Lids with a dish brush to remove food before placing them on the dishwasher top rack; do not use the sanitise cycle for the cups.
3. Wash the pitcher. Rinse and briefly scrub the Pitcher before dishwasher washing, without the sanitise cycle. Alternatively, hand-wash with soap and water, using a brush or sponge on stuck food and avoiding the sharp blades.
4. Clean the tamper. Hand-wash the Tamper with soap and water; use a dish brush or sponge to remove stuck food.
5. Dry and inspect the blade. Dry the Easy-Twist Extractor Blade completely after washing. Check its underside for cracks or breakage and replace a damaged blade before using the blender. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
6. Store the clean parts. Store the Pitcher upright with its Lid secured and nothing on top. Keep other pieces somewhere safe from damage and never leave the Easy-Twist Extractor Blade exposed on the Motor Base without a Cup or Pitcher covering it.

1. Begin cleaning. Turn off and unplug the blender; wait until all parts stop, then remove the Pitcher or Cup from the Motor Base.
2. Fill the vessel for a cleaning blend. Fill the Cup or Pitcher to its liquid MAX line with room-temperature water at 21°C, then add one or two drops of dish soap.
3. Run the cleaning blend for that vessel. For a Cup, twist the Extractor Blade tightly onto it and mount the assembly on the Motor Base. For a Pitcher, secure the Pitcher Lid with its Vented Lid Cap inserted and lock the Pitcher onto the Motor Base. Plug in and blend on LOW for 20–30 seconds.
4. Stop and detach the vessel. When the rinse blend finishes, power off, unplug and wait for every part to stop before detaching the vessel; then continue with the washing steps below.
5. Clean the base. Wipe the outside of the unplugged Motor Base with a clean cloth. NEVER submerge the motor base in water. Do not take the motor base apart.

Next steps

1. Clear the actuator area. Use a small brush to clear residue around the actuator system while the Motor Base is unplugged.
2. Wash the pitcher. Rinse and briefly scrub the Pitcher with a dish brush before dishwasher washing, or hand-wash with soap and water. Use a brush or sponge on stuck food and keep clear of the sharp blades.
3. Wash the cups and lids. Rinse and briefly scrub Cups and To-Go Lids with a dish brush before putting them on the dishwasher top rack; do not use the sanitise cycle.
4. Wash the detachable blade and other accessories. Before first use, rinse detachable parts and wash them with warm soapy water; the first-use instructions also permit dishwasher washing for parts other than the Motor Base, without heat or sanitise cycles.
5. Store the clean pitcher. Store the Pitcher upright with its Lid secured and nothing on top; keep remaining parts somewhere safe from damage.

1. Find the full product code on the NutriBullet Power Core Plus appliance label. NEVER submerge the motor base in water.
2. Use the NutriBullet Power Core Plus user guide supplied with that product code for washing each part and checking dishwasher permission