The NutriBullet Ultra 1200 Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Ultra 1200. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Essentials Set extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Essentials Set stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Essentials Set blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Essentials Set extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Essentials Set blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Essentials Set gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Essentials Set blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Essentials Set cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Essentials Set blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Essentials Set cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Essentials Set blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 900 Mega Pack extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 900 Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 900 Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 900 Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 900 Mega Pack blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 900 Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 900 Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 900 Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 900 Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 900 Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 900 Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 600 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 600 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 600 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Stop and unplug the NutriBullet Ultra 1000 / Ultra 1000 Premium. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1000 / Ultra 1000 Premium blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1000 / Ultra 1000 Premium cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1000 / Ultra 1000 Premium component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1000 / Ultra 1000 Premium gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1000 / Ultra 1000 Premium blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1000 / Ultra 1000 Premium cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1000 / Ultra 1000 Premium blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1000 / Ultra 1000 Premium cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1000 / Ultra 1000 Premium blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet Select 1200 / 2.0 Select 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Select 1200 / 2.0 Select 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Select 1200 / 2.0 Select 1200 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet Select 1200 / 2.0 Select 1200 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet Select 1200 / 2.0 Select 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Select 1200 / 2.0 Select 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Select 1200 / 2.0 Select 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check the ingredients and liquid against the MAX line on the NutriBullet Select 1200 / 2.0 Select 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Select 1200 / 2.0 Select 1200 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet Select 1200 / 2.0 Select 1200 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet Select 1200 / 2.0 Select 1200 replacement assembly and check its gasket before fitting it to the cup.

The NutriBullet Pro+ 1200 / Pro Plus 1200 extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet Pro+ 1200 / Pro Plus 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Pro+ 1200 / Pro Plus 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Pro+ 1200 / Pro Plus 1200 extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Pro+ 1200 / Pro Plus 1200 blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet Pro+ 1200 / Pro Plus 1200 gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet Pro+ 1200 / Pro Plus 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Pro+ 1200 / Pro Plus 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Pro+ 1200 / Pro Plus 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Pro+ 1200 / Pro Plus 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Pro+ 1200 / Pro Plus 1200 blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet 2.0 Pro 1000 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 2.0 Pro 1000 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 2.0 Pro 1000 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 2.0 Pro 1000 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 2.0 Pro 1000 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet 2.0 Pro 1000 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 2.0 Pro 1000 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 2.0 Pro 1000 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 2.0 Pro 1000 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 2.0 Pro 1000 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet 2.0 Pro 1000 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet 2.0 Pro 1000 replacement assembly and check its gasket before fitting it to the cup.

The NutriBullet 1000 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1000 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1000 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1000 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1000 Series blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 1000 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1000 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 1000 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1000 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1000 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1000 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo 1000 Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo 1000. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo 1000 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo 1000 cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo 1000 component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo 1000 gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo 1000 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo 1000 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo 1000 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo 1000 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo 1000 blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1000 Mega Pack / 1000 Series Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 1200 Series / 12 Piece extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1200 Series / 12 Piece stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1200 Series / 12 Piece blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1200 Series / 12 Piece extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1200 Series / 12 Piece blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 1200 Series / 12 Piece gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1200 Series / 12 Piece blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 1200 Series / 12 Piece cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1200 Series / 12 Piece blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1200 Series / 12 Piece cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1200 Series / 12 Piece blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 1200 Series / 10 Piece extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 1200 Series / 10 Piece stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 1200 Series / 10 Piece blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 1200 Series / 10 Piece extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 1200 Series / 10 Piece blade. On the replacement, leave the gasket installed during cleaning. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the NutriBullet 1200 Series / 10 Piece gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 1200 Series / 10 Piece blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 1200 Series / 10 Piece cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 1200 Series / 10 Piece blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 1200 Series / 10 Piece cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 1200 Series / 10 Piece blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet 2.0 Pro 1200 easy-twist extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 2.0 Pro 1200 stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 2.0 Pro 1200 blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 2.0 Pro 1200 easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 2.0 Pro 1200 blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 2.0 Pro 1200 gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet 2.0 Pro 1200 blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet 2.0 Pro 1200 cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 2.0 Pro 1200 blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 2.0 Pro 1200 cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 2.0 Pro 1200 blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet 2.0 Pro 1200 easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet 2.0 Pro 1200 replacement assembly and check its gasket before fitting it to the cup.

• Do not remove the gasket. Removing it permanently damages the extractor blade and causes leakage.

• Replace the complete extractor blade when its seal is loose or damaged.
• Inspect your blades before each use. We recommend replacing the extractor blade every 6 months for best performance.

• Keep the extractor blade out of the dishwasher. Hand wash it in warm soapy water and rinse.
• Leave the gasket in place. Dry the blade completely. Stand it on its side in the dish drainer so both sides dry.

• Replace the complete NutriBullet 500 Series / 4 Piece extractor blade if its gasket is loose or damaged, and have support confirm the matching replacement if the gasket is missing. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the NutriBullet 500 Series blade gasket is loose or damaged, replace the complete extractor blade; do not remove the gasket. Keep a blade with a missing gasket out of use. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• For product code NB5-0407DG, use the compatible NBM-BA031 extractor blade when replacing the complete blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Stop, unplug and wait for all movement to stop. If the sealed cup is warm, let it cool completely before carefully opening it away from your face and body; do not force a stuck cup open.
• Look at the gasket without pulling it out. It must be completely seated before use. Removing it permanently damages the extractor blade and can cause leakage.
• If the gasket is loose, missing or damaged, stop using that blade and replace the complete extractor blade assembly with the approved part for this model. Do not push a loose ring back in or use another appliance’s blade. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check that the extractor blade is screwed tightly onto the cup. Keep the ingredients and liquid at or below MAX, and use cool ingredients and liquid at 21°C or below.
• Check the cup and its three side tabs for cracks, crazing, breaks or rounding. Replace a damaged cup or one with a missing tab.
• If the connection still leaks or does not fit securely, stop using the affected parts and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase). If liquid has entered the motor base, leave the appliance off for assessment.

1. Unplug before removing normally releasing parts. Hand-wash the extractor with warm soapy water and rinse; keep it out of the dishwasher and do not remove its gasket.
2. Dry both sides of the extractor completely. Cups and to-go lids can go on the dishwasher’s top rack, but never use the sanitising cycle, which can warp the plastic.
3. Cleaning cannot repair a loose or damaged gasket. Replace the complete extractor blade if its gasket is not intact and fully seated. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

The NutriBullet 700 Series extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 700 Series stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 700 Series blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 700 Series extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 700 Series blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 700 Series gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 700 Series blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 700 Series cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 700 Series blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 700 Series cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 700 Series blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• With the NutriBullet Select 1000 / Select 1000 with pitcher stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the easy-twist extractor blade; keep fingers clear of the cutting edges.
• Look around the easy-twist extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Select 1000 / Select 1000 with pitcher blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before fitting a replacement easy-twist extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet Select 1000 / Select 1000 with pitcher easy-twist extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the easy-twist extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet Select 1000 / Select 1000 with pitcher blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet Select 1000 / Select 1000 with pitcher gasket in place and wash the detached easy-twist extractor blade by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the easy-twist extractor blade, taking care around the sharp edges.
• Dry the NutriBullet Select 1000 / Select 1000 with pitcher blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Remove the stopped NutriBullet Select 1000 / Select 1000 with pitcher cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the easy-twist extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Select 1000 / Select 1000 with pitcher blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Check the ingredients and liquid against the MAX line on the NutriBullet Select 1000 / Select 1000 with pitcher cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Select 1000 / Select 1000 with pitcher blending action.
• Refit the undamaged easy-twist extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Turn the detached NutriBullet Select 1000 / Select 1000 with pitcher easy-twist extractor blade over without touching the cutting edges and inspect the bottom for cracking or breakage.
• Replace a damaged easy-twist extractor blade immediately; replacing or pushing in a rubber ring will not repair a cracked blade body. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the correct NutriBullet Select 1000 / Select 1000 with pitcher replacement assembly and check its gasket before fitting it to the cup. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Set the NutriBullet Pro+ Matte Black extractor blade aside and look at the ring without pulling out any remaining rubber.
• For a loose or damaged extractor-blade gasket, replace the complete blade assembly; the gasket is not a separately fitted repair.
• Use the product code N12-1207MK-C when asking for the correct NutriBullet Pro+ Matte Black blade.

• Keep the loose ring with the NutriBullet Pro+ Matte Black component it came from, and photograph both parts.

The NutriBullet 600 Essentials Kit extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Essentials Kit stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Essentials Kit blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Essentials Kit extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Essentials Kit blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 600 Essentials Kit gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Essentials Kit blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 600 Essentials Kit cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Essentials Kit blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Essentials Kit cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Essentials Kit blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Stop and unplug the NutriBullet Ultra 1200 McLaren / Club Pack. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 McLaren / Club Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 McLaren / Club Pack cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 McLaren / Club Pack component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 McLaren / Club Pack gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 McLaren / Club Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Ultra 1200 McLaren / Club Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 McLaren / Club Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 McLaren / Club Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 McLaren / Club Pack blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Ultra 1200 Premium Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Ultra 1200 Premium. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Ultra 1200 Premium blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket. Buy a replacement extractor blade (New Zealand).
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Ultra 1200 Premium cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Ultra 1200 Premium component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Ultra 1200 Premium gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Ultra 1200 Premium blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it. Buy a replacement extractor blade (New Zealand).

• Remove the stopped NutriBullet Ultra 1200 Premium cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Ultra 1200 Premium blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Ultra 1200 Premium cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Ultra 1200 Premium blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

• Power off the NutriBullet Triple Prep System, unplug it and wait for the blades to stop. If the sealed cup feels hot or warm, leave it in place for at least 30 minutes and longer if still warm; do not handle or remove it until completely cool.
• Once the cup is cool, detach it from the motor base. Point it away from your face and body and use a towel to slowly untwist the blade, releasing any remaining pressure; then inspect the Extractor Blade gasket without touching the cutting edges.
• Stop using the affected blade if the gasket is absent, split or damaged. Arrange the correct replacement blade assembly through support before blending again.

• Detach the Extractor Blade from the cup only after the contents are cool and the motor is stopped.
• Use a small brush or sponge dampened in soapy water to remove residue from the Extractor Blade.
• Inspect the cleaned blade before reuse. If a seal is still displaced or damaged, leave the blade out of service and chat with us for the matching replacement.

• Inspect the NutriBullet Triple Prep System cup for cracks, cloudiness or other damage and replace a damaged cup.
• With an intact gasket and undamaged cup, twist the Extractor Blade onto the cup until tightly sealed.
• If the parts will not join securely, stop using that attachment and have the model and replacement part checked. Use genuine parts intended for the NutriBullet Triple Prep System.

• With the NutriBullet Blender Combo 1200 switched off, unplugged and fully stopped, detach the cup and blade assembly from the motor base.
• Inspect the gasket around the easy-twist extractor blade without touching the cutting edges. Do not pull the gasket out for cleaning or try to fit a separate replacement ring.
• If the gasket has come out, set the easy-twist extractor blade aside and replace the complete blade assembly before blending again. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Look at the exposed gasket and the bottom of the easy-twist extractor blade; check for a split seal, cracking or breakage.
• A damaged gasket needs a replacement easy-twist extractor blade, even if the NutriBullet Blender Combo 1200 has only been used a few times.

• Dishwasher hot water can damage the seal around the NutriBullet Blender Combo 1200 blade attachment.
• If the seal is now loose or damaged, replace the blade attachment; cleaning will not repair the seal.
• For the replacement blade, hand-wash with soap and water instead of placing it in the dishwasher.

• Hand-wash the detached easy-twist extractor blade with soap and water, keeping fingers away from sharp edges.
• Use a small brush or sponge to remove stuck food from the accessible surfaces; leave the blade assembly intact.
• Dry the easy-twist extractor blade completely and inspect again. Only use an intact blade with its gasket in place; replace a blade whose seal is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• If the gasket is intact and in place, align the easy-twist extractor blade with the cup and twist it on until tightly sealed.
• Check the cup and blade attachment for cracks or damaged threads if they will not join securely.
• Stop using the damaged part and replace it with the correct NutriBullet Blender Combo 1200 part; do not continue blending with a loose connection.

• Check the product code on the NutriBullet SmartSense Blender; include NBF07600 if that is the code shown.
• Note whether the ring came from the lid, pitcher or another accessory, and keep it with that part.
• Send support a photo of the ring, its original position and the complete part so the correct repair or replacement can be specified.

• Check the product code on the NutriBullet SmartSense Blender Combo; include NBF07700-1507 if that is the code shown.
• Note whether the ring came from the lid, pitcher or another accessory, and keep it with that part.
• Send support a photo of the ring, its original position and the complete part so the correct repair or replacement can be specified.

• With the NutriBullet Smart Touch Blender Combo switched off, unplugged and fully stopped, detach the cup and blade assembly from the motor base.
• Inspect the gasket around the easy-twist extractor blade without touching the cutting edges. Do not pull the gasket out for cleaning or try to fit a separate replacement ring.
• If the gasket has come out, set the easy-twist extractor blade aside and replace the complete blade assembly before blending again.
• Look at the exposed gasket and the bottom of the easy-twist extractor blade; check for a split seal, cracking or breakage.
• A damaged gasket needs a replacement easy-twist extractor blade, even if the NutriBullet Smart Touch Blender Combo has only been used a few times.

• Dishwasher hot water can damage the seal around the NutriBullet Smart Touch Blender Combo blade attachment.
• If the seal is now loose or damaged, replace the blade attachment; cleaning will not repair the seal.
• For the replacement blade, hand-wash with soap and water instead of placing it in the dishwasher.

• Hand-wash the detached easy-twist extractor blade with soap and water, keeping fingers away from sharp edges.
• Use a small brush or sponge to remove stuck food from the accessible surfaces; leave the blade assembly intact.
• Dry the easy-twist extractor blade completely and inspect again. Only use an intact blade with its gasket in place; replace a blade whose seal is loose or damaged.

• If the gasket is intact and in place, align the easy-twist extractor blade with the cup and twist it on until tightly sealed.
• Check the cup and blade attachment for cracks or damaged threads if they will not join securely.
• Stop using the damaged part and replace it with the correct NutriBullet Smart Touch Blender Combo part; do not continue blending with a loose connection.

• Turn off and unplug the NutriBullet Power Core Blender, wait for all parts to stop and remove the Pitcher from the Motor Base.
• Inspect the Pitcher for cracks or damage; replace a damaged Pitcher rather than continuing to blend with it. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
• For a loose ring without an obvious origin, send support a photo of the ring and the pitcher or lid so the correct component can be identified.

• Hand-wash the detached Pitcher and lid with warm, soapy water; use a dish brush or sponge on stuck-on food.
• Once the parts are clean and undamaged, fit the Pitcher Lid with its cap, aligning the rear loop opposite the spout with the handle.
• The lid must sit securely before blending. If a piece remains loose or a seal is missing, keep the affected part out of use and request the correct replacement.

• With the NutriBullet Blender Combo 1000 switched off, unplugged and fully stopped, detach the cup and blade assembly from the motor base.
• Inspect the gasket around the easy-twist extractor blade without touching the cutting edges. The gasket must sit completely within the blade assembly.
• If the gasket has come out, set the easy-twist extractor blade aside and replace the complete blade assembly before blending again. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Look at the exposed gasket and the bottom of the easy-twist extractor blade; check for a split seal, cracking or breakage.
• A damaged gasket needs a replacement easy-twist extractor blade, even if the NutriBullet Blender Combo 1000 has only been used a few times.

• Hand-wash the detached easy-twist extractor blade with soap and water, keeping fingers away from sharp edges.
• Use a small brush or sponge to remove stuck food from the accessible surfaces; leave the blade assembly intact.
• Dry the easy-twist extractor blade completely and inspect again. Only use an intact blade with its gasket in place; replace a blade whose seal is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• If the gasket is intact and in place, align the easy-twist extractor blade with the cup and twist it on until tightly sealed.
• Check the cup and blade attachment for cracks or damaged threads if they will not join securely.
• Stop using the damaged part and replace it with the correct NutriBullet Blender Combo 1000 part; do not continue blending with a loose connection.

• Power off the NutriBullet Power Core Blender Combo, unplug it and wait for the blades to stop. If the sealed cup feels hot or warm, leave it in place for at least 30 minutes and longer if still warm; do not handle or remove it until completely cool.
• Once the cup is cool, detach it from the motor base. Point it away from your face and body and use a towel to slowly untwist the blade, releasing any remaining pressure; then inspect the Extractor Blade gasket without touching the cutting edges.
• Stop using the affected blade if the gasket is absent, split or damaged. Arrange the correct replacement blade assembly through support before blending again.

• Detach the Extractor Blade from the cup only after the contents are cool and the motor is stopped.
• Wash the detachable parts with warm, soapy water and remove visible food residue from accessible surfaces.
• Inspect the cleaned blade before reuse. If a seal is still displaced or damaged, leave the blade out of service and chat with us for the matching replacement.

• Inspect the NutriBullet Power Core Blender Combo cup for cracks, cloudiness or other damage and replace a damaged cup.
• With an intact gasket and undamaged cup, twist the Extractor Blade onto the cup until tightly sealed.
• If the parts will not join securely, stop using that attachment and have the model and replacement part checked. Use genuine parts intended for the NutriBullet Power Core Blender Combo.

• Check the product code on the NutriBullet Power Core Plus; include NBF07200AKP if that is the code shown.
• Note whether the ring came from the lid, pitcher or another accessory, and keep it with that part.
• Send support a photo of the ring, its original position and the complete part so the correct repair or replacement can be specified.

• Disconnect the NutriBullet Portable Blender charging cable and leave the blender undisturbed for two minutes until the light ring is off. Check that the blades have stopped before taking off the Cup or Lid.
• Inspect the Cup, Lid and blade area for wear, cracking or a visibly displaced seal. Keep your fingers away from the sharp blades.
• If a seal has come out, or a component is damaged, leave the blender out of use and chat with us to identify the correct replacement. Do not remove the blade assembly to reach a seal; chat with us for the blade-removal instructions first.

• Check whether the NutriBullet Portable Blender was left in a vehicle, near a heat source or in direct sunlight. Extreme temperatures can damage the seals and other components.
• Inspect the removable Cup and Lid before reassembly. Replace a damaged detachable part; for a damaged Motor Base, chat with us.
• For future cleaning, wash only the Cup and Lid on the dishwasher top rack without the heat or sanitise cycle. Keep the Motor Base out of the dishwasher.

• With the NutriBullet Portable Blender switched off, twist the Cup into position so the two alignment dots on the Cup and Motor Base line up.
• Twist the Lid onto the Cup and place the Lid Latch upright in its locked position.
• Check that the Cup is secure and the lid is closed before use. If either part cannot fit properly, stop and have that part checked instead of blending with a loose connection.

• Remove the Cup and Lid from the powered-off NutriBullet Portable Blender and hand-wash them with warm, soapy water, then rinse.
• Gently rinse only the blade assembly and wipe it with a damp sponge or cloth. Do not run the Motor Base under water.
• Inspect the clean parts again. Cleaning is not a repair for a seal that is still loose, absent or damaged; keep the blender out of use until the affected part is checked.

• Unplug the NutriBullet Flip Stainless and leave it undisturbed for 90 seconds so it shuts down; check that the blades have stopped.
• With the blender upright, check the Flip-Top Lid on the Motor Base, Blade, and Lid assembly. Before blending, this lid must snap closed and seal. NEVER submerge the entire Motor Base, Blade, and Lid in water.
• Twist the Motor Base, Blade, and Lid assembly securely onto the Blending Cup. If the Flip-Top Lid cannot close, or a seal is loose or missing, keep the blender out of use and chat with us to check the assembly.

• Check which lid is fitted to the NutriBullet Flip Stainless. The separate To-Go Lid is not leak-proof.
• Keep the Cup upright with this lid fitted; liquid seeping from a tipped To-Go Lid does not by itself mean a gasket is missing. If the lid is damaged, stop using that lid and obtain a replacement.

• Check whether the NutriBullet Flip Stainless was exposed to extreme temperatures or stored in a freezer or refrigerator. The guide warns that these conditions can damage seals and other components.
• Look for damage to the Cup, lids and accessible seal areas without taking the Motor Base, Blade, and Lid assembly apart.
• Do not use a damaged part. Have the affected assembly checked and obtain the appropriate replacement before blending again.

• After the NutriBullet Flip Stainless has shut down, open the Flip-Top Lid. Carefully rinse the sip hole under a gentle flow of warm water while covering the USB-C port with your thumb or finger.
• Use the supplied Cleaning Brush for the sip hole and vent hole. Wipe the assembly dry and leave it upright with the Flip-Top Lid open.
• Once clean and dry, close the lid again and check that it snaps shut. If the seal remains displaced or the lid will not close, stop using the assembly and seek replacement advice; do not dismantle it to retrieve the seal.

• Unplug the NutriBullet Flip Tritan and leave it undisturbed for 90 seconds so it shuts down; check that the blades have stopped.
• With the blender upright, check the Flip-Top Lid on the Motor Base, Blade, and Lid assembly. Before blending, this lid must snap closed and seal. NEVER submerge the entire Motor Base, Blade, and Lid in water.
• Twist the Motor Base, Blade, and Lid assembly securely onto the Blending Cup. If the Flip-Top Lid cannot close, or a seal is loose or missing, keep the blender out of use and chat with us to check the assembly.

• Check which lid is fitted to the NutriBullet Flip Tritan. The separate To-Go Lid is not leak-proof.
• Keep the Cup upright with this lid fitted; liquid seeping from a tipped To-Go Lid does not by itself mean a gasket is missing. If the lid is damaged, stop using that lid and obtain a replacement.

• Check whether the NutriBullet Flip Tritan was exposed to extreme temperatures or stored in a freezer or refrigerator. The guide warns that these conditions can damage seals and other components.
• Look for damage to the Cup, lids and accessible seal areas without taking the Motor Base, Blade, and Lid assembly apart.
• Do not use a damaged part. Have the affected assembly checked and obtain the appropriate replacement before blending again.

• After the NutriBullet Flip Tritan has shut down, open the Flip-Top Lid. Carefully rinse the sip hole under a gentle flow of warm water while covering the USB-C port with your thumb or finger.
• Use the supplied Cleaning Brush for the sip hole and vent hole. Wipe the assembly dry and leave it upright with the Flip-Top Lid open.
• Once clean and dry, close the lid again and check that it snaps shut. If the seal remains displaced or the lid will not close, stop using the assembly and seek replacement advice; do not dismantle it to retrieve the seal.

• Unplug the blender charger and leave the blender undisturbed for 90 seconds until the light ring powers down into Sleep Mode. Wait for the blades to stop, keep the Sip Cap closed, then twist the Sip Lid with Carry Loop counter-clockwise to remove it.
• Wash the lid with warm, soapy water and rinse. Remove excess moisture from the gasket area, then gently guide the displaced gasket back into place.
• Let the lid dry fully before twisting it clockwise onto the Cup. If the gasket will not stay in place, is missing or is damaged, stop using that lid and arrange a replacement instead of repeatedly blending with it loose.

• Press the Sip Cap down over the Sip Spout.
• Listen and feel for the click: this indicates the Cap is closed and the seal is engaged. Lower the Carry Loop for blending.
• If there is no click, open the Cap and clean the Sip Lid with Carry Loop, then dry it completely. A cap that still cannot close needs replacement advice before the lid is used again.

• With the blender off and disconnected from the charger, detach the Motor Base and check that the Blade Block is completely dry.
• Twist the Blade Block blades-first into the bottom of the Blending Cup until it reaches the built-in soft-stop. That friction is part of the sealing fit; do not force the connection.
• Place the assembled Cup and Blade Block onto the Motor Base and gently twist to lock. If the soft-stop or lock cannot be reached, stop assembly and have the affected part checked.

• Inspect the Cup, Sip Lid with Carry Loop and Blade Block for damage or wear. Extreme temperatures can damage the seals.
• Keep a damaged or incomplete component out of use and arrange a suitable replacement. The gentle refitting step above is for the Sip Lid gasket displaced during cleaning.
• Hand-wash the detachable parts with warm, soapy water and rinse them clean. Keep the Motor Base out of the dishwasher.

• Press the NutriBullet GO power button once to stop blending. Wait until no light is on and the blades have stopped before separating the Cup from the base.
• Inspect the Cup, lid and accessible blade-assembly area for damage. If a seal has come away or a component is damaged, stop using the blender and chat with us to identify the correct replacement.
• Do not attempt to repair or service the NutriBullet GO yourself. Keep the Blade Cover screwed onto the base when the Cup is removed for storage.

• For an intact NutriBullet GO Cup and base, hold the base from underneath, turn it upside down and lower it onto the Cup rim.
• Twist the base clockwise to fasten it firmly, then press and hold the power button for three seconds. The blue light flashes when the Cup and base are locked and ready.
• If the connection cannot lock, or the light alternates red and blue after the Cup has been secured, stop and have the connection checked. Do not blend with a loose or damaged Cup.

• After switching the NutriBullet GO off, wash the Cup and lid with warm, soapy water and rinse, or place them on the dishwasher top rack.
• Gently rinse the blade assembly and clean it with a damp sponge or cloth while avoiding the sharp edges. Do not run the Motor Base under water or put the blade assembly in the dishwasher.
• Inspect the clean connection before reassembly. If a seal is still missing or loose, leave the blender out of use and chat with us so our team can check it.

• Remove the Juice Pitcher lid from the NutriBullet Juicer 800W and empty the pitcher. Wash the detached pitcher and lid with warm, soapy water and rinse clean.
• For the original NutriBullet Juicer 800W (NBJ07100), refit the lid and close its latch. Keep the pitcher upright with nothing placed on its lid.
• If the lid cannot close securely, stop using it for sealed storage and ask for the correct replacement lid or pitcher assembly.

• With the NutriBullet Juicer 800W switched off and unplugged, check the detached pitcher and lid for damage and identify exactly where the loose piece came from.
• Stop using a damaged detachable part and replace it with the correct part for your model. Keep the loose piece for identification; do not try to repair the juicer yourself.
• Use the model details when requesting a replacement. The sealing lid belongs to the Juice Pitcher; a leak from a different juicer connection needs its own part identified before a seal is ordered.

• Remove the Juice Pitcher lid from the NutriBullet Juicer 800W 2.0 and empty the pitcher. Wash the detached pitcher and lid with warm, soapy water and rinse clean.
• For the NutriBullet Juicer 800W 2.0 (NBJ07150), refit the lid securely on top. Keep the pitcher upright with nothing placed on its lid.
• If the lid cannot close securely, stop using it for sealed storage and ask for the correct replacement lid or pitcher assembly.

• With the NutriBullet Juicer 800W 2.0 switched off and unplugged, check the detached pitcher and lid for damage and identify exactly where the loose piece came from.
• Stop using a damaged detachable part and replace it with the correct part for your model. Keep the loose piece for identification; do not try to repair the juicer yourself.
• Use the model details when requesting a replacement. The sealing lid belongs to the Juice Pitcher; a leak from a different juicer connection needs its own part identified before a seal is ordered.

• Switch the NutriBullet Cold Press Slow Juicer off, unplug it and wait for the motor and grinding assembly to stop completely and cool.
• Remove the Juice and Pulp Containers, closing the juice spout with its cover to prevent drips. Twist the Juice Bowl Cover counter-clockwise and lift it off, then remove the Auger from the bowl. Lift the Juice Bowl off the Motor Base before removing the Rotating Bowl Brush and Juicing Screen together from the bowl.
• Look underneath the Juice Bowl and put the pulp plug back into its proper position in the pulp spout, following the assembly illustration in the user guide. Do not use the juicer with a missing or damaged plug.
• Refit the Juice Bowl firmly onto the Motor Base, assemble the Juicing Screen, Rotating Bowl Brush and Auger, and lock the Juice Bowl Cover. If the plug cannot remain in its proper position, leave the juicer out of use and arrange replacement advice.

• With the NutriBullet Cold Press Slow Juicer disassembled and unplugged, pull the pulp plug out of the pulp spout for cleaning.
• Use the narrow end of the Cleaning Brush inside the pulp spout to remove trapped pulp. Run water through the Juice Bowl and pulp spout to flush out the remainder, then wash the detachable components in warm, soapy water.
• Let the parts dry thoroughly and return the plug to the position shown in the assembly guide before rebuilding the juicer. If residue cannot be cleared or the plug will not fit, do not run the juicer; have the affected part checked.

• Inspect the cleaned NutriBullet Cold Press Slow Juicer parts before fitting them together. Identify whether the loose piece belongs to the pulp spout or to a different component.
• Stop using any damaged part and obtain the correct replacement. Do not attempt to repair or service the juicer yourself.
• When requesting parts, identify the NutriBullet Cold Press Slow Juicer and the affected component; the Juice Spout Cover and the pulp plug have different locations and functions.

• Remove the Juice Pitcher lid from the NutriBullet Juicer Pro 1000W and empty the pitcher. Wash the detached pitcher and lid with warm, soapy water and rinse clean.
• Replace the lid firmly, close the latch and keep the pitcher upright. Leave the top of the lid clear of other items during storage.
• If the lid cannot close securely, stop using it for sealed storage and ask for the correct replacement lid or pitcher assembly.

• With the NutriBullet Juicer Pro 1000W switched off and unplugged, check the detached pitcher and lid for damage and identify exactly where the loose piece came from.
• Stop using a damaged detachable part and replace it with the correct part for your model. Keep the loose piece for identification; do not try to repair the juicer yourself.
• Use the model details when requesting a replacement. The sealing lid belongs to the Juice Pitcher; a leak from a different juicer connection needs its own part identified before a seal is ordered.

• Turn the NutriBullet Cold Press Batch Juicer Dial to OFF, unplug it and wait for the Auger to stop.
• Open the Lid, hold the handle and twist the Hopper counter-clockwise until the arrows are no longer aligned, then lift it off. Pull the Auger straight up, lift the Juicing Bowl from the Motor Base, and empty the detached Hopper and Juicing Bowl.
• Check the underside of the Juicing Bowl. Push the Silicone Cover firmly back into place after cleaning; it must be fully pushed in and flush.
• If the cover stays proud, keeps moving or is missing, do not re-use the juicer until the affected component has been checked or replaced.

• Rinse the detached NutriBullet Cold Press Batch Juicer Hopper, Auger and Juicing Bowl under running water.
• Use the Cleaning Brush on the Auger. Clean under the Juicing Bowl, including the Silicone Cover, Spouts and Spout Cover; hand-wash removable pieces with warm, soapy water.
• Push the Silicone Cover flush again, place the Juicing Bowl onto the Motor Base with spouts aligned to the notches, then press it securely into place.
• Insert the Auger fully and, with the Lid open, turn the Hopper clockwise until the orange dot disappears. If parts cannot seat properly after cleaning, keep the juicer out of use and have them checked.

• Check the NutriBullet Cold Press Batch Juicer Silicone Cover, Juicing Bowl and other detached parts for damage before reassembly.
• Do not use a damaged Auger, Hopper, strainer or other removable part. Replace the damaged component rather than forcing it into position.
• For future washing, avoid metal sponges and abrasive pads. Do not use the dishwasher sterilise cycle: its high temperatures can deform parts.

• Locate the NutriBullet Cold Press Batch Juicer Juice Spout Cover on the outlet above the Juice Cup; this is separate from the Silicone Cover underneath the Juicing Bowl.
• Open the Juice Spout Cover to release juice into the Juice Cup. If the bowl becomes too full, open the cover to let juice out; close it when juicing is finished.
• If the spout cover itself is detached or damaged, stop using that part and arrange the correct replacement. Refitting the underside Silicone Cover does not repair a damaged outlet cover.

• Switch the NutriBullet Immersion Blender 800W off, unplug it and wait until the blade or whisk has fully stopped.
• Detach the motor body from the blending arm, whisk or chopping bowl attachment; inspect the attachment for damage without touching a blade edge. NEVER submerge the main unit in water.
• The blending arm is one single part. If its structure is damaged, replace the attachment; send a photo of any loose ring and its location to support to identify the correct part. Buy a replacement blending arm (Australia) or blending arm (New Zealand).

• Clean the whisk holder, chopping bowl lid and blending arm with warm, soapy water; do not soak them or put them in the dishwasher.
• Wash the chopping bowl, whisk, blending cup and chopping blade in warm, soapy water or the dishwasher, then let the parts dry thoroughly.
• Check the separated parts again. Do not resume using an attachment while a ring is missing, a part is damaged or the correct assembly is uncertain.

• Unplug the NutriBullet EveryGrain Cooker and let it cool completely before cleaning. NEVER submerge the main unit in water.
• Wipe the Sealing Panel and Condensation Collector with a damp cloth or sponge and warm, soapy water; do not use steel wool.
• Remove the Steam Vent plug, rinse it with warm water and wipe inside the Steam Vent with a damp cloth.
• Check that visible food residue has been removed. If the Sealing Panel or any ring is still loose, keep the cooker off and provide support with a photo; cleaning is not a repair for a displaced or damaged part.

• With the lid components intact, lower the Cooker Lid fully.
• Listen for the click that shows the lid is closed and locked.
• If the lid will not latch or a loose part prevents closure, stop using the cooker and request the correct replacement; do not force the lid.

• Check the grain and liquid quantities against the Measuring & Cook Time Guide on pages 14–15 of the user guide.
• Use the listed ratio for the grain you are preparing; too much liquid can cause leakage during cooking.
• If leakage continues with the correct quantities, or a seal or panel is visibly displaced, keep the cooker out of use and have that part checked.

• Power off and unplug the NutriBullet Limitless Food Processor; wait until the blade or disc has completely stopped before removing attachments.
• Hold the blade by its plastic grip, away from the cutting edge, and inspect the Work Bowl, Lid and attachment for damage.
• Replace a damaged part with a genuine matching component; for a loose ring, send support a photo of the ring and where it came from before fitting a replacement.

• Clean detachable parts with warm, soapy water; remove food residue after every use and avoid steel wool or the dishwasher heat/sanitise cycle.
• With all parts intact, lock the Work Bowl onto the Motor Base by turning its handle clockwise until it clicks.
• Lock the Work Bowl Lid so its markings line up with the handle. If the Lid will not lock, or the ring is still missing or displaced, keep the processor off and have the affected part checked.

• Unplug the NutriBullet Baby, wait for moving parts to stop, and detach the Short Cup or Batchbowl and extractor blade from the Motor Base.
• Inspect the gasket without pulling it out; before use it must be completely seated in the blade.
• If it has come loose or been removed, stop using the blade assembly and replace it. Attempting to remove the gasket can permanently damage the blade and cause leakage. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Keep the extractor blade out of the dishwasher; hot dishwasher water can damage the outer seal.
• Do not sterilise the extractor blade or plastic parts in boiling water or steam, which can warp or damage them.
• Hand-wash the blade with warm, soapy water and rinse, keeping clear of sharp edges. If the gasket is already loose or damaged, replace the blade before further use. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• With the gasket fully seated and the parts undamaged, twist the extractor blade onto the Short Cup or Batchbowl until sealed.
• Check the connection before placing the assembly on the Motor Base; use the Batchbowl with its Lid firmly in place.
• If the blade will not remain securely attached, keep that assembly out of use and arrange a matching replacement component.

• For the Easy-Pop Freezer Tray, keep food below two-thirds full and snap every side of the Freezer Tray Lid closed.
• Use the Date-Dial Storage Cups for refrigerated food rather than freezing; do not fill them more than two-thirds full.
• If a lid or another part has broken or lost a piece, stop using the damaged part and request its matching replacement rather than applying the blade-gasket instructions to it.

• Turn off and unplug the NutriBullet Baby Steam + Blend; let it cool for at least 10 minutes and wait for the Blending Blade and motor to stop before disassembly.
• Compare the loose piece and Blade Holder with the assembly diagram on printed pages 10–11 of the user guide.
• Keep the ring with the Blade Holder and send support a photo of both sides of the part and its location so the correct fitting or replacement can be specified.

• Allow the appliance to cool completely before cleaning, and empty the Work Bowl.
• To remove the Blade Holder from the Work Bowl for cleaning, rotate the bottom of the Blade Holder; handle the Blending Blade only by a non-sharp area.
• Wash the Blade Holder and Blending Blade in warm, soapy water and dry thoroughly; do not put these two parts in the dishwasher.
• Check that residue is gone. If the ring remains loose, is damaged or is missing, do not test-run the appliance; arrange the correct replacement or fitting advice.

• For intact, complete parts, lower the Blending Blade vertically onto the Blade Holder in the centre of the Work Bowl.
• Turn the Work Bowl Lid clockwise until secure; line up the Work Bowl black arrow with the Motor Base Unlock icon, then turn the bowl counter-clockwise to lock it.
• The bowl and lid must be firmly positioned before use. If a missing ring or damaged part prevents proper assembly, leave the appliance off until the part is replaced.

• Unplug the Magic Bullet To Go 200W and wait for every moving part to stop. Remove the Cup and Cross Blade from the Motor Base, turn the Cup upright and unscrew the Cross Blade.
• Inspect the rubber gasket in the Cross Blade without pulling it out. It should be undamaged and completely seated in the blade assembly.
• If the gasket is worn, torn or loose, stop using the Cross Blade and replace the whole blade attachment. A gasket that keeps coming out after only a few uses still needs this replacement action. Buy a replacement cross blade (Australia) or cross blade (New Zealand).

• Keep the Magic Bullet To Go 200W Cross Blade out of use if the seal has been removed or is missing.
• Do not try to push a replacement ring into the blade housing. The gasket is factory-sealed and is not designed to be removed or replaced separately.
• Order the correct complete Cross Blade for the Magic Bullet To Go 200W. Keep the old blade aside until the replacement is available.

• Check how the Magic Bullet To Go 200W blade attachment was cleaned. The guide warns that dishwasher hot-water exposure can damage its outer-rim seal.
• Inspect the gasket without disturbing it; if loose or damaged, replace the whole Cross Blade. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• For a sound blade, hand-clean it as instructed in the guide and keep it out of the dishwasher. Never pull the gasket out to clean underneath it.

• Check the Magic Bullet To Go 200W Cup and Cross Blade for damage before assembly. Clean the separate components and inspect the seated gasket again.
• Twist the Cross Blade onto the Cup until firmly sealed and hand-tightened, with the blade attachment aligned properly.
• If the connection cannot tighten, or the Cup is cracked or damaged, stop using that component and replace it. A loose blade-to-Cup connection should not be corrected by removing the blade gasket.

• Unplug the Magic Bullet Value Pack 200W and wait for every moving part to stop. Remove the Cup and Cross Blade from the Motor Base, turn the Cup upright and unscrew the Cross Blade.
• Inspect the rubber gasket in the Cross Blade without pulling it out. It should be undamaged and completely seated in the blade assembly.
• If the gasket is worn, torn or loose, stop using the Cross Blade and replace the whole blade attachment. A gasket that keeps coming out after only a few uses still needs this replacement action. Buy a replacement cross blade (Australia) or cross blade (New Zealand).

• Keep the Magic Bullet Value Pack 200W Cross Blade out of use if the seal has been removed or is missing.
• Do not try to push a replacement ring into the blade housing. The gasket is factory-sealed and is not designed to be removed or replaced separately.
• Order the correct complete Cross Blade for the Magic Bullet Value Pack 200W. Keep the old blade aside until the replacement is available.

• Check how the Magic Bullet Value Pack 200W blade attachment was cleaned. The guide warns that dishwasher hot-water exposure can damage its outer-rim seal.
• Inspect the gasket without disturbing it; if loose or damaged, replace the whole Cross Blade. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• For a sound blade, hand-clean it as instructed in the guide and keep it out of the dishwasher. Never pull the gasket out to clean underneath it.

• Check the Magic Bullet Value Pack 200W Cup and Cross Blade for damage before assembly. Clean the separate components and inspect the seated gasket again.
• Twist the Cross Blade onto the Cup until firmly sealed and hand-tightened, with the blade attachment aligned properly.
• If the connection cannot tighten, or the Cup is cracked or damaged, stop using that component and replace it. A loose blade-to-Cup connection should not be corrected by removing the blade gasket.

• Turn the Magic Bullet Blender Combo off, unplug it and wait until the blades have stopped. If the sealed Cup feels hot or warm, leave it on the Motor Base without touching or opening it for at least 30 minutes; allow more time if it is still warm.
• Only when the Cup is completely cool, slowly disengage it from the Motor Base. Point the Cup away from your face and body, cover the Cross Blade with a towel and slowly untwist it to release residual pressure. Do not force or pry apart a stuck assembly; chat with us for help.
• Check the Cross Blade gasket without pulling it out. A displaced or damaged seal can cause leakage; a missing or damaged gasket means the Cross Blade must be taken out of use.
• The blade seal is non-removable and cannot be replaced separately. Chat with us to arrange the correct blade-assembly replacement before using the affected attachment again.

• For an intact Magic Bullet Blender Combo Cross Blade, check that the Cup or Blending Pitcher is undamaged and clean.
• Securely tighten the Cross Blade onto the Cup or Blending Pitcher before fitting the vessel to the Motor Base.
• If a leak starts during blending, turn the power off and wait for the motor to stop. For a hot or warm sealed Cup, follow the cooling and opening steps above before removal; inspect the seal and replace a damaged attachment before reuse.

• Hand-clean the Magic Bullet Blender Combo blade attachment under lukewarm water and keep its seal in place.
• Do not expose the attachment to boiling water, a microwave, an oven or the dishwasher heat/sanitise cycle. Those conditions can damage components.
• Inspect the clean gasket before reassembly. If it is loose, damaged or missing, stop using the Cross Blade and arrange replacement; cleaning will not restore a damaged seal.

• Remove the Magic Bullet Mini Juicer Juice Cup Lid and empty the Cup. Wash the detached Cup and lid in warm, soapy water and rinse.
• Refit the Juice Cup Lid tightly and close the latch for storage. Keep the Cup upright and leave the top of the lid clear.
• If the lid will not close or a piece has come away, stop using the lid for sealed storage and request the correct replacement part.

• Switch the Magic Bullet Mini Juicer off, unplug it and wait for all moving parts to stop before inspecting the detached component.
• Identify where the loose piece came from and check the surrounding part for damage. Do not operate with a damaged component; replace the affected part.
• Ask for replacement advice using the Magic Bullet Mini Juicer model and part details. Keep the loose piece available to identify the correct assembly.

• Turn the Magic Bullet Kitchen Express 250W control knob to OFF, unplug the Motor Base and wait for the blade or disc to stop.
• Remove the affected vessel from the Motor Base and identify whether the loose piece came from the Cup and Cross Blade or from the work bowl and lid.
• Do not use any part that appears damaged. Have the affected component identified for replacement before using it again; keep the loose piece with it for checking.

• With the Magic Bullet Kitchen Express 250W disconnected, check the intact Cup and Cross Blade for food residue and clean the separate parts.
• Twist the Cross Blade assembly onto the Cup until the two are tightly sealed. Turn the assembly upside down and twist clockwise onto the Motor Base to lock it.
• If the blade assembly will not tighten correctly, leave it out of use and replace the affected component instead of blending with an insecure connection.

• Inspect the Magic Bullet Kitchen Express 250W Cup, work bowl and lid for damage after washing.
• Clean removable parts on the dishwasher top rack or hand-wash with warm, soapy water and rinse. Never use the sanitise cycle; it can warp the Cup or work bowl.
• Do not force a warped component into position. Stop using the damaged part and obtain the correct replacement.

• Power off the NutriBullet Ultra Plus+ Compact Kitchen System, unplug it and wait for the blades to stop. If the sealed cup feels hot or warm, leave it in place for at least 30 minutes and longer if still warm; do not handle or remove it until completely cool.
• Once the cup is cool, detach it from the motor base. Point it away from your face and body and use a towel to slowly untwist the blade, releasing any remaining pressure; then inspect the Rapid Extractor Blade gasket without touching the cutting edges.
• Stop using the affected blade if the gasket is absent, split or damaged. Arrange the correct replacement blade assembly through support before blending again.

• Detach the Rapid Extractor Blade from the cup only after the contents are cool and the motor is stopped.
• Use a small brush or sponge dampened in soapy water to remove residue from the Rapid Extractor Blade.
• Inspect the cleaned blade before reuse. If a seal is still displaced or damaged, leave the blade out of service and chat with us for the matching replacement.

• Inspect the NutriBullet Ultra Plus+ Compact Kitchen System cup for cracks, cloudiness or other damage and replace a damaged cup.
• With an intact gasket and undamaged cup, twist the Rapid Extractor Blade onto the cup until tightly sealed.
• If the parts will not join securely, stop using that attachment and have the model and replacement part checked. Use genuine parts intended for the NutriBullet Ultra Plus+ Compact Kitchen System.

The NutriBullet 600 Mega Pack extractor blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• With the NutriBullet 600 Mega Pack stopped and unplugged and the cup contents cool, remove the cup and blade assembly from the motor base. Place the cup upright, then unscrew the extractor blade; keep fingers clear of the cutting edges.
• Look around the extractor blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet 600 Mega Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement extractor blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Treat a gasket removed from the NutriBullet 600 Mega Pack extractor blade as a blade-assembly problem, even if the ring looks intact.
• Do not press the ring back into the extractor blade or buy a loose ring to fit yourself; removing blade components can permanently damage the assembly and lead to leakage.
• Replace that complete NutriBullet 600 Mega Pack blade. On the replacement, leave the gasket installed during cleaning.

• Keep the NutriBullet 600 Mega Pack gasket in place and wash the detached extractor blade by hand with warm soapy water.
• Rinse the extractor blade after washing and clean visible residue without lifting the gasket.
• Dry the NutriBullet 600 Mega Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet 600 Mega Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the extractor blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet 600 Mega Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet 600 Mega Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet 600 Mega Pack blending action.
• Refit the undamaged extractor blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo 1000 Deluxe Set Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo 1000 Deluxe Set. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo 1000 Deluxe Set blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo 1000 Deluxe Set cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo 1000 Deluxe Set component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo 1000 Deluxe Set gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo 1000 Deluxe Set blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo 1000 Deluxe Set cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo 1000 Deluxe Set blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo 1000 Deluxe Set cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo 1000 Deluxe Set blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.

The NutriBullet Turbo Ultimate Pack Rapid Extractor Blade must have an intact gasket before blending. A ring that comes out, repeatedly lifts, or has split needs attention to the blade assembly, even if the blender is nearly new.

• Stop and unplug the NutriBullet Turbo Ultimate Pack. If the cup is hot or warm, leave it attached to the motor base and allow it to cool for at least 30 minutes; wait longer if it is still warm. Only when completely cool, remove the cup and blade assembly, point the cup away from your face and body, and slowly unscrew the Rapid Extractor Blade; keep fingers clear of the cutting edges.
• Look around the Rapid Extractor Blade gasket for a missing section, a split, visible damage or a ring that has lifted out of place. Do not pull it out to inspect underneath.
• Stop using the affected NutriBullet Turbo Ultimate Pack blade and replace the complete blade assembly if the gasket is loose, missing or damaged. Do not run a blend to test a failed gasket.
• Before fitting a replacement Rapid Extractor Blade, check that its gasket is present, undamaged and securely in position. If the replacement also has a loose gasket, leave it unused and ask for help.

• Inspect the NutriBullet Turbo Ultimate Pack cup and Rapid Extractor Blade for cracking, cloudiness, warping or other damage after cleaning.
• Stop using any damaged detachable NutriBullet Turbo Ultimate Pack component and replace it with the correct genuine part.
• Keep the Rapid Extractor Blade, cup and To-Go Lid off the dishwasher bottom rack, and do not use a heat or sanitise cycle. Do not boil these parts or heat them in an oven or microwave to clean them.

• Keep the NutriBullet Turbo Ultimate Pack gasket in place and wash the detached Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand with warm soapy water.
• Use a small brush or sponge to remove food residue from the Rapid Extractor Blade, taking care around the sharp edges.
• Dry the NutriBullet Turbo Ultimate Pack blade completely before putting it away or refitting it.
• After cleaning, check the seal again. If the ring has lifted or any damage is visible, replace the blade instead of repeating the cleaning or blending with it.

• Remove the stopped NutriBullet Turbo Ultimate Pack cup and blade assembly from the unplugged motor base; keep the cup upright while checking the connection.
• If the gasket and cup are undamaged, screw the Rapid Extractor Blade onto the cup until securely attached and tightly sealed before returning the assembly to the motor base.
• If the NutriBullet Turbo Ultimate Pack blade will not attach securely, or leakage continues with the correct undamaged parts fitted, stop using the affected assembly and ask for replacement advice.

• Check the ingredients and liquid against the MAX line on the NutriBullet Turbo Ultimate Pack cup before reassembly.
• Reduce the contents to at or below MAX; leaving space is necessary for the NutriBullet Turbo Ultimate Pack blending action.
• Refit the undamaged Rapid Extractor Blade securely. If the gasket itself is loose or missing, reducing the fill level does not make that blade usable.