1. Prepare for washing. Turn NutriBullet Portable Blender off after use, disconnect the charger and wait for the blades to stop before removing the Cup or cleaning.
2. Loosen residue with a rinse blend. For stuck residue, add cold water and a drop of soap to the Cup without passing MAX, fit the Lid and lock its latch; press Power to wake, wait about one second, then press again for one 20-second cycle. Turn off and wait for the blades to stop before washing.
3. Wash the cup and lid. Hand-wash the Cup and Lid in warm soapy water and rinse clean, or put them on the dishwasher top rack without the heat or sanitise cycle.
4. Clean the fixed blades. Gently rinse only the blade assembly and wipe it with a damp sponge or cloth; keep your fingers away from the sharp blades.
5. Protect the motor base. Do not place the motor base under running water or put the motor base in the dishwasher.
6. Wipe and dry the motor base. Gently wipe and dry the Motor Base with a clean cloth. NEVER submerge the motor base in water or cleaning liquid.
7. Store the blender. Store upright in a safe place with the Cup attached to cover the blades; do not stack anything on top.

1. Prepare to clean Flip. Disconnect the charger and leave NutriBullet Flip Stainless undisturbed for 90 seconds so it shuts down completely; check that the blades have stopped before taking parts apart.
2. Prepare a cleaning blend. Rinse out the Blending Cup with fresh water, add a drop of dish soap and fill the cup halfway with water.
3. Start the cleaning cycle. Secure the Motor Base, Blade, and Lid on the Cup with the Flip-Top Lid closed. Wake the blender with Power, then press Power again to start the 30-second cycle; flip and shake the blender to agitate the water.
4. Rinse afterwards. When the cycle ends, open the Flip-Top Lid over the sip hole and empty the soapy water; repeat one cycle with fresh water only, without soap.
5. Switch from the cleaning blend to hand washing. After the final rinse cycle, disconnect the charger and leave Flip undisturbed for 90 seconds to shut down completely; check that the blades have stopped before hand washing or removing parts.
6. Clean the Blending Cup. Wash the Blending Cup with soap and water.

Next steps

1. Rinse the blades. Point the blade downward at an angle and carefully rinse only the blade area, keeping a thumb or finger over the USB-C port. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the entire Motor Base, Blade, and Lid assembly.
2. Clean the drinking spout. With the blade facing upwards, carefully rinse the sip hole under a gentle flow of warm water while covering the USB-C port with a thumb or finger.
3. Reach narrow openings. Use the supplied Cleaning Brush for the straw, under the blades, the sip hole and the vent hole.
4. Dry Flip fully. Wipe the Motor Base, Blade, and Lid and pat the USB-C port dry with a clean cloth. Stand the assembly upright with the Flip-Top Lid open and allow it to dry fully in a sunny area before charging; avoid excessive heat and keep within the guide’s recommended 10–40°C storage and charging range.
5. Store Flip. Store in a dry, temperature-controlled place with the Cup or Blade Cover attached over the blades; put nothing on top.

1. Take Flex apart. Use these steps for NutriBullet Flex Portable NBPB07222 and Flex Portable McLaren Papaya NBPB07222PA-MC. Check the remaining charge on the LED Battery Bar, then turn the blender off and disconnect the charger. Gently twist the Cup and Blade Block off the Motor Base, holding the Cup and base without pushing down or gripping the Sip Lid. Twist the Blade Block clockwise to remove it, keeping clear of the blades; close the Sip Cap before twisting the Sip Lid with Carry Loop anticlockwise.
2. Wash the detachable parts. Hand-wash the Blade Block with warm soapy water and rinse clean, taking care around its sharp blades. Wash the Blending Cup and Sip Lid with Carry Loop with warm soapy water, or put those two parts on the dishwasher top rack without a heat or sanitise cycle.
3. Clean the motor base. Wipe food from the Motor Base with a damp cloth. Keep its Silicone Charge Port Cover in place. NEVER submerge the motor base in water. Never put the base in the dishwasher or run the motor base under water.
4. Dry before reassembly. Dry the Blade Block completely before attaching it to the Cup. Fully dry the Sip Lid before blending or storage; air-dry with the Sip Cap open to avoid trapped moisture around the seal.
5. Store Flex. Store upright with the Blade Block secured to the Blending Cup and the Sip Lid attached so the blades stay covered; do not stack objects on top.

1. Prepare GO for cleaning. Turn NutriBullet GO off and check that no light is on; wait for the motor and blades to stop before separating the cup.
2. Wash the cup and lid. Place the Cup and Lid on the dishwasher top rack, or hand-wash them with warm soapy water and rinse.
3. Clean the blades. Gently rinse the blade assembly and carefully wipe it with a damp sponge or cloth, without touching the sharp edges.
4. Store GO. Keep all parts together in a safe place; screw the Blade Cover onto the Motor Base when it is not in use.