What size is my portable blender, and how much can it hold?

Cup capacity and the MAX blending limit depend on your portable blender model. Select your model for its capacity and filling limit.

NutriBullet Portable Blender / Portable Blender McLaren

The Cup holds 590 mL in total, but food and liquid must stay at or below its MAX mark for blending.

How much can I add?

Use the 590 mL Cup supplied for the NutriBullet Portable Blender; stop adding ingredients at its MAX mark, even if there is room above it.
Leave room for the blend to move by using sufficient liquid; do not pack the Cup with ice. Overfilling can stop the blade or cause leakage.
Line up the Cup and Motor Base dots, screw on the Lid and keep its latch upright and locked before blending.

How do I empty, clean and store the Cup?

Wait for the blades to stop, lower the Lid Latch and press the release button to drink through the spout.
Wash the Cup and Lid in warm soapy water and rinse, or place them on the dishwasher’s top rack without a heat or sanitise cycle.
Store the blender upright with the Cup attached to cover the blade, with nothing stacked on top.
Stop using a cracked, cloudy or otherwise damaged Cup and replace it before your next blend.

The stainless-steel Cup holds 590 mL in total, with a 475 mL MAX limit for the combined blending ingredients.

What do the capacity marks mean?

The stainless-steel Blending Cup has a 590 mL total capacity and a 475 mL MAX blending line. Measure the combined liquid and food against MAX.
Follow the Cup’s minimum-liquid mark as well as MAX; ice must not exceed 25% of total Cup volume.
Twist the Motor Base, Blade, and Lid tightly onto the Cup and snap the Flip-Top Lid closed before blending.

Can I carry or store the drink in the Cup?

For the separate To-Go Lid, remove the powered lid after the blades stop and twist the To-Go Lid onto the Cup. Open its front flap to sip, or keep that flap closed and slide the centre tab back to use a straw. Keep this lid upright: it is not leak-proof.
Do not leave the assembled Flip in a refrigerator or freezer, and do not leave blended food sealed in the Cup for prolonged periods.
Wash the Blending Cup with soap and water; the Cup and To-Go Lid may also go on the dishwasher’s top rack. Keep the Motor Base, Blade, and Lid out of the dishwasher. NEVER submerge the entire Motor Base, Blade, and Lid in water.
Clean and dry the powered lid, cover its blade with the Cup or Blade Cover, and store in a dry location with nothing on top.

The Blending Cup holds 650 mL in total, but the MAX mark is the filling limit for all food and liquid combined.

How should I fill the 650 mL Cup?

Use the measurement markings on the 650 mL Blending Cup, and stop when all food and liquid together reach MAX.
Use sufficient liquid and leave space for ingredients to circulate; do not overfill with ice, which can block the blade.
Fit a completely dry Blade Block through the Cup’s bottom opening and twist to its soft-stop. Add ingredients, close and lock the Sip Lid, then gently twist the assembly onto the Motor Base.

How do I use it as a to-go cup?

After blending stops, grip the Cup and Motor Base and gently twist the Cup off; do not press downward or pull on the Sip Lid.
Move the Carry Loop away to expose the release button and press to open the Sip Cap. Press the Cap closed until it clicks and the seal engages; move the Carry Loop over it to help prevent accidental opening.
To hold the open Sip Cap out of the way, lightly press it down toward the Cup; press up and away to release it. Keep the Sip Cap closed while attaching or removing the Sip Lid.
Switch off before disassembly. Twist the Blade Block off clockwise and the Sip Lid counter-clockwise. Hand-wash the Blade Block with warm soapy water and rinse clean. Wash the Cup and Sip Lid in warm soapy water or on the dishwasher’s top rack without a heat or sanitise cycle.
Dry the Sip Lid completely, including its gasket area; if the gasket has shifted, guide it gently back into its groove. Store upright with Cup, Blade Block and Sip Lid fitted to cover the blades, and nothing on top.

The Cup has a total capacity of 385 mL and a MAX blending capacity of 300 mL, including all food and liquid.

How much fits in the GO Cup?

The GO Cup holds 385 mL in total, but its MAX blending line is 300 mL. Include every solid and liquid ingredient in that limit and leave a little space at the top.
Use cool or room-temperature food and liquids; do not add ice, frozen ingredients, hot liquid or carbonated drinks.
If an overfilled Cup stops the blade, press Power to switch off and wait for all movement to stop. Invert the assembly, detach the Cup, remove excess food and refit below MAX.

How do I remove, wash and store the Cup?

After switching off and waiting for the blade to stop, invert the blender and twist the base counter-clockwise off the Cup. Screw the Blade Cover onto the base while it is detached.
Wash the Cup and Lid in warm soapy water and rinse, or use the dishwasher’s top rack. The Motor Base and blade assembly must stay out of the dishwasher.
Store all parts together in a safe place where they cannot be damaged or cause harm.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: Read the NutriBullet Flip Stainless user guide (PDF)

The full steps for this model are in its user guide: Read the NutriBullet GO user guide (PDF)