Stop using an appliance that seems unsafe; keep damaged parts out of use and seek support for burning smells, electrical faults or damage before using it again. The model-specific checks explain when cleaning, refitting or cooling is appropriate and when the appliance must stay out of use.
Before inspecting removable parts, switch off, disconnect from power, wait for all moving parts to stop and let hot parts cool. Keep sharp edges away from your fingers, and follow the instructions for a warm or stuck sealed cup before opening it.
If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.
NutriBullet Juicer 800W
Stop using your NutriBullet Juicer 800W if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Is the Sieve mesh torn, crinkled, bent or worn?
- Turn NutriBullet Juicer 800W off, unplug it and wait until the Sieve has completely stopped. Release the Locking Handle, lift the Pulp Basin with its cover and Sieve off the Motor Base, then remove the Basin Cover.
- Hold the Sieve by its upper rim and lift it out, avoiding the sharp teeth on its lower disc. Inspect the mesh and rim for tears, creases, distortion or other damage.
- Replace a damaged Sieve; never straighten its mesh or run it to test the damage. Louder or unusual noise or vibration can indicate wear; extreme vibration means the juicer must remain out of use for assessment. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
Is the Pulp Basin, Basin Cover or Locking Handle damaged?
- After power is disconnected and all movement has stopped, lower the Locking Handle away from the cover’s side ears. Lift the Pulp Basin away from the Motor Base.
- Inspect the basin, cover, side ears and handle. A crack or broken locking feature requires replacement of the affected part; do not try to run the juicer with an unsecured cover.
- For intact replacement parts, align the basin spout with the dimpled side of the Motor Base, click the Sieve onto the drive coupling, align the cover ears with the basin ears and lock the handle into them. If it will not lock, leave the juicer off.
Is the Juice Pitcher, lid or No-Drip Spout damaged?
- Stop juicing before taking the Juice Pitcher from beneath the spout. Check the pitcher, its lid and the spout for a cracked edge, broken hinge or loss of shape.
- Keep a damaged detachable part out of use and identify the replacement by the exact product code. Do not assume a pitcher or spout from another juicer will fit.
- When using intact parts, position the spout inside the open lid of the Juice Pitcher and keep the pitcher upright. Empty it before it is full; close the spout only after juicing is stopped and the pitcher is removed.
Is residue hiding damage or has a part warped during cleaning?
- Rinse the removed parts and use the Cleaning Brush to clear the Sieve under running water, keeping away from the sharp teeth. For dried pulp on the Sieve, the guide allows a 30-minute hot-water soak before brushing.
- Do not use a dishwasher sterilise cycle, which can deform parts. Wipe the Motor Base with a clean damp cloth only.
- Inspect the clean parts. Replace cracks, distorted mesh or warped parts; cleaning cannot repair a structural fault.
Is the motor straining because produce is being pushed too fast?
- Switch off and wait for rotation to stop before clearing a blockage. Remove frozen fruit and vegetables and foods with little extractable juice, such as banana or avocado. Remove hard pits and citrus rind, and cut produce small enough to pass easily through the feed chute.
- Choose HIGH for hard produce such as carrots and beetroot; use LOW for softer produce. Start the motor before adding food, then feed gradually using only the Food Pusher. Do not force ingredients down.
- If the pusher does not clear the obstruction with gentle pressure, stop and disconnect the juicer before disassembly. Persistent strain after cleaning and correct assembly needs assessment.
Is accumulated pulp or a blocked Sieve affecting operation?
- Stop and disconnect the juicer when the Pulp Basin is full. Remove the basin, cover and Sieve using the disassembly sequence above, and empty the pulp.
- Brush the Sieve holes under running water, then rinse and inspect the cover and basin. Reassemble only once the mesh is clear and undamaged.
- On the next properly assembled use, pulp should collect in the basin while juice flows into the pitcher. If the juicer still vibrates excessively or sounds abnormal, discontinue use for assessment.
Do the lights indicate an unsecured basin or cover?
- A power button that flashes three times then stays lit after selecting speed indicates incorrect assembly. A flashing power button after a mid-run stop points to the Locking Handle.
- Switch off and unplug before checking. Seat the Pulp Basin on the Motor Base, fit the Basin Cover and secure the Locking Handle in the cover ears.
- The handle must lock securely. If an intact assembly still will not lock or the same warning returns, leave the juicer off; do not hold or bypass the handle to keep it running.
Did the juicer stop after a long run or flash all lights three times?
- If the power button remains lit after a mid-run stop, the guide identifies more than ten minutes of continuous running. All lights flashing three times indicates overheating.
- Unplug and leave the motor off for at least 15 minutes. During the pause, review the feed rate, suitable speed and pulp/Sieve checks above.
- Only resume with an undamaged, correctly assembled juicer and no electrical-fault symptoms. If it stops again after cooling and a lighter load, stop testing and arrange assessment.
Is juice spilling because the outlet or collection parts are not ready?
- Turn off the juicer before moving the pitcher or investigating a spill. With the Motor Base dry and unaffected, check the pitcher is upright under the spout, has room for more juice, and the Pulp Basin is not full.
- Open the No-Drip Spout for juicing and place it into the pitcher lid opening.
- Clean and dry a surface spill before continuing. If liquid has entered or collected underneath the Motor Base, use the electrical-fault check above rather than attempting another run. NEVER submerge the motor base in water.
Is the juicer unstable or are moving parts accessible?
- Position the assembled juicer on a stable, dry, level worktop with air space around and beneath it, and keep the cord clear of the edge and hot surfaces.
- Keep children, hands, hair, clothing and tools away from the feed chute and moving parts. Supervise operation and use only the supplied Food Pusher.
- Do not operate an incompletely assembled juicer. If the surface moves or the juicer vibrates extremely, switch off and leave it out of use until the cause has been assessed.
NutriBullet Cold Press Slow Juicer
Stop using your NutriBullet Cold Press Slow Juicer if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Is the Auger cracked, bent, chipped or damaged?
- Turn NutriBullet Cold Press Slow Juicer off, unplug and wait for the Auger to stop completely and cool before handling.
- Twist the Juice Bowl Cover anticlockwise and lift it off. Lift out the Auger, then remove the Juice Bowl with its Juicing Screen and Rotating Bowl Brush; separate the brush from the screen.
- Inspect the removed Auger before reuse. Replace it if damaged; do not attempt to bend it back, glue it or run it with missing material.
Is the Juice Bowl, Juice Bowl Cover or a collection container damaged?
- With the machine disconnected and the Auger removed, check the Juice Bowl, Juice Bowl Cover, juice container and pulp container for cracks or damaged locking edges.
- Replace the affected detachable part with the correct part for the product code. Do not use a broken container or try to hold a lid shut by hand.
- For intact replacements, secure the Juice Bowl on the Motor Base, place the Juicing Screen inside the Rotating Bowl Brush and seat them in the bowl. Press and turn the Auger onto its axis, then turn the cover clockwise until the locked symbol aligns with the bowl’s triangle. If the parts will not seat securely, keep the juicer off.
Is the Juicing Screen damaged or the Rotating Bowl Brush out of shape?
- Remove the screen and brush assembly from the disconnected juicer and slide the brush away from the screen. Handle the sharp screen carefully.
- Use the Cleaning Brush and running water to clear screen holes. Wash the Auger by hand with warm soapy water and a soft cloth; never put the Auger in the dishwasher or clean parts with a metal sponge.
- Inspect the clean screen and brush. A damaged component needs replacement before reassembly; do not force a distorted screen into the bowl.
Is the pulp seal, spout cover or outlet damaged or misplaced?
- Look under the removed Juice Bowl at the pulp plug in the pulp spout. Pull it out to clean the outlet, then put the intact plug fully back in its proper position before assembly.
- Check the juice outlet and its cover for a crack or broken hinge. If the plug, cover or bowl is torn, worn or damaged, keep that part out of use and ask for a correctly matched replacement.
- After an intact assembly is refitted, place both collection containers under their outlets and open the juice outlet for dispensing. If leakage continues with correct assembly, stop and arrange assessment.
Are ingredients stuck or is the motor straining?
- Switch off before changing direction, and wait until the Auger has stopped.
- For a jam without damage or electrical-fault symptoms, the guide says to press the RESET switch under the base, then hold REV for a few seconds. If that does not work, switch off, unplug and reassemble using the sequence above.
- Use only the supplied food pusher and gentle pressure. If the Auger still stalls after clearing and correct assembly, stop testing and have the juicer assessed.
Has the motor become hot or stopped during juicing?
- Unplug and allow the motor to cool for at least 15 minutes before any further use. Do not use this cooling procedure to retry a damaged appliance or an electrical fault.
- Do not exceed 15 minutes of juicing at a rapid rate or with firm pressure; allow at least one minute of rest between uses. Cut produce to fit and reduce pusher pressure.
- After cooling, reassemble clean, intact parts and use suitable produce. If the motor stops again, leave the juicer off and arrange assessment.
Could unsuitable food or too much food be overloading the juicer?
- Remove frozen ingredients, hard pits and foods with little juice such as bananas, avocados or coconut. Prepare fresh fruit and vegetables to fit easily and remove citrus rind.
- Use small, manageable amounts and gentle pressure. Alternate softer produce with firmer pieces and empty the Juice and Pulp Containers before the next cycle.
- If suitable produce still will not pass through without force, stop and use the blockage checks rather than pushing harder.
Could a closed spout or a full container be causing a spill?
- Stop the juicer before moving collection containers. Check that the juice container is under the juice spout and the pulp container is under the pulp spout; empty both before they overflow.
- Check the juice spout cover is open for dispensing and the pulp plug is correctly fitted under the Juice Bowl.
- Clean and dry a spill on the worktop before continuing. A wet Motor Base needs the electrical-fault response above; recurring leakage from an intact, correctly assembled bowl needs assessment. NEVER submerge the motor base in water.
Is the juicer unstable, poorly ventilated or open around moving parts?
- Place NutriBullet Cold Press Slow Juicer on a stable, level, clean, dry counter and allow air to circulate with at least 200 mm above and on all sides.
- Fit and lock the Juice Bowl Cover before operation. Keep fingers, hair, clothing and utensils away from the feed opening; supervise use and keep children clear.
- If a cover or interlock does not secure the assembly, stop using the juicer. Do not bypass the interlock or remove a cover while the Auger is turning.
Are parts difficult to separate after juicing?
- If the only issue is food residue after an otherwise normal run, the guide allows about 30 seconds of processing without adding more food to clear the Auger and Juicing Screen. Do not do this if a part is damaged or an electrical fault is suspected.
- Then switch off, unplug, allow the motor to stop and cool, and follow the disassembly sequence above. Rinse removed parts and clear the screen with the Cleaning Brush.
- If parts still will not separate, do not pry against the bowl or sharp screen. Leave the assembly intact for assistance.
NutriBullet Juicer Pro 1000W
Stop using your NutriBullet Juicer Pro 1000W if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Is the Sieve mesh torn, crinkled, bent or worn?
- Turn NutriBullet Juicer Pro 1000W off, unplug it and wait until the Sieve has completely stopped. Release the Locking Handle, lift the Pulp Basin with its cover and Sieve off the Motor Base, then remove the Basin Cover.
- Hold the Sieve by its upper rim and lift it out, avoiding the sharp teeth on its lower disc. Inspect the mesh and rim for tears, creases, distortion or other damage.
- Replace a damaged Sieve; never straighten its mesh or run it to test the damage. Louder or unusual noise or vibration can indicate wear; extreme vibration means the juicer must remain out of use for assessment. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
Is the Pulp Basin, Basin Cover or Locking Handle damaged?
- After power is disconnected and all movement has stopped, lower the Locking Handle away from the cover’s side ears. Lift the Pulp Basin away from the Motor Base.
- Inspect the basin, cover, side ears and handle. A crack or broken locking feature requires replacement of the affected part; do not try to run the juicer with an unsecured cover.
- For intact replacement parts, align the basin spout with the dimpled side of the Motor Base, click the Sieve onto the drive coupling, align the cover ears with the basin ears and lock the handle into them. If it will not lock, leave the juicer off.
Is the Juice Pitcher, lid or No-Drip Spout damaged?
- Stop juicing before taking the Juice Pitcher from beneath the spout. Check the pitcher, its lid and the spout for a cracked edge, broken hinge or loss of shape.
- Keep a damaged detachable part out of use and identify the replacement by the exact product code. Do not assume a pitcher or spout from another juicer will fit.
- When using intact parts, position the spout inside the open lid of the Juice Pitcher and keep the pitcher upright. Empty it before it is full; close the spout only after juicing is stopped and the pitcher is removed.
Is residue hiding damage or has a part warped during cleaning?
- Rinse the removed parts and use the Cleaning Brush to clear the Sieve under running water, keeping away from the sharp teeth. For dried pulp on the Sieve, the guide allows a 30-minute hot-water soak before brushing.
- Do not use a dishwasher sterilise cycle, which can deform parts. Wipe the Motor Base with a clean damp cloth only.
- Inspect the clean parts. Replace cracks, distorted mesh or warped parts; cleaning cannot repair a structural fault.
Is the motor straining because produce is being pushed too fast?
- Switch off and wait for rotation to stop before clearing a blockage. Remove frozen fruit and vegetables and foods with little extractable juice, such as banana or avocado. Remove hard pits and citrus rind, and cut produce small enough to pass easily through the feed chute.
- Choose HIGH or TURBO for harder produce using the guide’s speed chart; use LOW for softer produce. Start the motor before adding food, then feed gradually using only the Food Pusher. Do not force ingredients down.
- If the pusher does not clear the obstruction with gentle pressure, stop and disconnect the juicer before disassembly. Persistent strain after cleaning and correct assembly needs assessment.
Is accumulated pulp or a blocked Sieve affecting operation?
- Stop and disconnect the juicer when the Pulp Basin is full. Remove the basin, cover and Sieve using the disassembly sequence above, and empty the pulp.
- Brush the Sieve holes under running water, then rinse and inspect the cover and basin. Reassemble only once the mesh is clear and undamaged.
- On the next properly assembled use, pulp should collect in the basin while juice flows into the pitcher. If the juicer still vibrates excessively or sounds abnormal, discontinue use for assessment.
Do the lights indicate an unsecured basin or cover?
- A power button that flashes three times then stays lit after selecting speed indicates incorrect assembly. A flashing power button after a mid-run stop points to the Locking Handle.
- Switch off and unplug before checking. Seat the Pulp Basin on the Motor Base, fit the Basin Cover and secure the Locking Handle in the cover ears.
- The handle must lock securely. If an intact assembly still will not lock or the same warning returns, leave the juicer off; do not hold or bypass the handle to keep it running.
Did the juicer stop after a long run or flash all lights three times?
- If the power button remains lit after a mid-run stop, the guide identifies more than ten minutes of continuous running. All lights flashing three times indicates overheating.
- Unplug and leave the motor off for at least 15 minutes. During the pause, review the feed rate, suitable speed and pulp/Sieve checks above.
- Only resume with an undamaged, correctly assembled juicer and no electrical-fault symptoms. If it stops again after cooling and a lighter load, stop testing and arrange assessment.
Is juice spilling because the outlet or collection parts are not ready?
- Turn off the juicer before moving the pitcher or investigating a spill. With the Motor Base dry and unaffected, check the pitcher is upright under the spout, has room for more juice, and the Pulp Basin is not full.
- Open the No-Drip Spout for juicing and place it into the pitcher lid opening; close it after stopping and removing the pitcher.
- Clean and dry a surface spill before continuing. If liquid has entered or collected underneath the Motor Base, use the electrical-fault check above rather than attempting another run. NEVER submerge the motor base in water.
Is the juicer unstable or are moving parts accessible?
- Position the assembled juicer on a stable, dry, level worktop with air space around and beneath it, and keep the cord clear of the edge and hot surfaces.
- Keep children, hands, hair, clothing and tools away from the feed chute and moving parts. Supervise operation and use only the supplied Food Pusher.
- Do not operate an incompletely assembled juicer. If the surface moves or the juicer vibrates extremely, switch off and leave it out of use until the cause has been assessed.
NutriBullet Cold Press Batch Juicer
Stop using your NutriBullet Cold Press Batch Juicer if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Is the Auger cracked, bent, chipped or damaged?
- Turn NutriBullet Cold Press Batch Juicer off, unplug and wait for the Auger to stop completely and cool before handling.
- Open the Lid, turn the Hopper anticlockwise until the arrows separate and lift it off. Lift out the Auger, then lift off the Juicing Bowl.
- Inspect the removed Auger before reuse. Replace it if damaged; do not attempt to bend it back, glue it or run it with missing material.
Is the Juicing Bowl, Hopper and Lid or a collection container damaged?
- With the machine disconnected and the Auger removed, check the Juicing Bowl, Hopper and Lid, juice container and pulp container for cracks or damaged locking edges.
- Replace the affected detachable part with the correct part for the product code. Do not use a broken container or try to hold a lid shut by hand.
- For intact replacements, align the bowl spouts with the Motor Base notches and press the bowl down. Fit the Auger firmly, open the Lid and twist the Hopper clockwise until its orange dot is no longer visible, then close the Lid. If the parts will not seat securely, keep the juicer off.
Is the pulp seal, spout cover or outlet damaged or misplaced?
- After lifting off the Juicing Bowl, inspect the Silicone Cover underneath, the spouts and Spout Cover. Clean these areas, then push an undamaged Silicone Cover fully back until it sits flush.
- Check the juice outlet and its cover for a crack or broken hinge. If the plug, cover or bowl is torn, worn or damaged, keep that part out of use and ask for a correctly matched replacement.
- After an intact assembly is refitted, place both collection containers under their outlets and open the juice outlet for dispensing. If leakage continues with correct assembly, stop and arrange assessment.
Are ingredients stuck or is the motor straining?
- Switch off before changing direction, and wait until the Auger has stopped.
- Turn the Dial briefly to REVERSE to release stuck ingredients. If this does not clear the blockage, turn off and unplug before removing the Hopper and Auger to clear residue.
- Use only the supplied food pusher / scraper tool and gentle pressure. If the Auger still stalls after clearing and correct assembly, stop testing and have the juicer assessed.
Has the motor become hot or stopped during juicing?
- Unplug and allow the motor to cool for at least 15 minutes before any further use. Do not use this cooling procedure to retry a damaged appliance or an electrical fault.
- Reduce the load in the Hopper and avoid force on the 2-in-1 Pusher & Scraper Tool.
- After cooling, reassemble clean, intact parts and use suitable produce. If the motor stops again, leave the juicer off and arrange assessment.
Could unsuitable food or too much food be overloading the juicer?
- Remove frozen ingredients, hard pits and foods with little juice such as bananas, avocados or coconut. Prepare fresh fruit and vegetables to fit easily and remove citrus rind. Remove apple seeds as directed by this guide.
- Use small, manageable amounts and gentle pressure. Do not overload the Hopper.
- If suitable produce still will not pass through without force, stop and use the blockage checks rather than pushing harder.
Could a closed spout or a full container be causing a spill?
- Stop the juicer before moving collection containers. Check that the juice container is under the juice spout and the pulp container is under the pulp spout; empty both before they overflow.
- Open the Juice Spout Cover to release juice from an overfull Juicing Bowl; close it only after juicing is finished.
- Clean and dry a spill on the worktop before continuing. A wet Motor Base needs the electrical-fault response above; recurring leakage from an intact, correctly assembled bowl needs assessment. NEVER submerge the motor base in water.
Is the juicer unstable, poorly ventilated or open around moving parts?
- Place NutriBullet Cold Press Batch Juicer on a stable, level, clean, dry counter and allow air to circulate around and under the Motor Base.
- Fit and lock the Hopper and Lid before operation. Keep fingers, hair, clothing and utensils away from the feed opening; supervise use and keep children clear.
- If a cover or interlock does not secure the assembly, stop using the juicer. Do not bypass the interlock or remove a cover while the Auger is turning.
Has a part been exposed to boiling water, a microwave or harsh cleaning?
- Disconnect the appliance, remove the affected part and let it cool before inspection.
- Do not microwave juicer parts or immerse them in or hold them over boiling water. Clean using running water or warm soapy water; avoid metal sponges, abrasive pads and dishwasher sterilise cycles.
- Inspect for warping, cracks or a loss of fit. Replace damaged parts and reassemble only parts that seat and lock normally.
Magic Bullet Mini Juicer
Stop using your Magic Bullet Mini Juicer if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Is the Sieve cracked, bent or damaged?
- Turn the Magic Bullet Mini Juicer OFF, unplug it and wait for the Sieve to stop completely before releasing the Locking Arms.
- Remove the Juice Bowl Cover, then lift the Juice Bowl from the base with the Sieve inside. Lift the Sieve vertically out, holding its top edges rather than its sharp teeth.
- Clean the Sieve with the supplied Cleaning Brush under running water. Inspect it for cracks, bends or other damage.
- Replace a damaged Sieve before juicing; do not straighten it or run the motor to test it. If pulp is merely blocking sound mesh, soak it in hot water for 30 minutes and brush again.
Is the Juice Bowl, cover, Juice Cup, Pulp Bin or a locking part broken?
- After the Magic Bullet Mini Juicer is disconnected and stationary, remove the Juice Cup and turn the Silicone Spout Cap upward to catch residual drips.
- Release both Locking Arms, detach the Pulp Bin by pulling its bottom outward at an angle, and lift away the cover and Juice Bowl.
- Wash the removable parts with warm soapy water and check for cracks or broken attachment points. Do not use a damaged protecting cover or force broken locking parts into position.
- Replace the affected component before reuse. Keep these parts out of microwaves, ovens, stovetop pots, boiling water and the dishwasher heat-sanitation cycle.
Do undamaged parts fail to seat or lock?
- With the Magic Bullet Mini Juicer unplugged, seat the Juice Bowl on the Motor Base in its keyed position, open side facing the rear. NEVER submerge the motor base in water.
- Align the Sieve with the motor drive coupling and push down until it clicks, gripping its top edges and avoiding the teeth.
- Place the Juice Bowl Cover with its Feed Chute over the Sieve and Pulp Chute at the back. Attach both Locking Arms in their upright locked position and fit the Pulp Bin.
- If a part cannot seat or a locking arm cannot stay engaged, do not operate the juicer; replace damaged hardware rather than bypassing its lock.
Has the motor overheated or stopped after a long run?
- Switch the Magic Bullet Mini Juicer OFF and unplug it. For an overheating stop, let it cool for 15 minutes before further use.
- Check that the motor has not been left running after juicing and that the base has free space beneath and around it. Clear dust, lint and coverings from the ventilation openings.
- Use fresh fruit and vegetables prepared to fit easily into the Feed Chute. Remove stones and citrus rind; do not use frozen produce or thick, juiceless foods such as bananas or avocados.
- After cooling, only resume with undamaged, properly assembled parts. If the motor stops again, keep it off for assistance.
Is food stuck, the Pulp Bin full or the motor straining as you feed?
- Stop the Magic Bullet Mini Juicer before trying to clear a persistent blockage. Keep fingers and utensils out of the Feed Chute.
- Use only the Food Pusher to guide food gently. If it will not move, disconnect power, wait for complete stop, then disassemble the cover and bowl to remove remaining food.
- Empty a full Pulp Bin and brush blocked Sieve holes clean; refit both parts before starting the motor.
- Feed small amounts gradually once the juicer is running. Do not force oversized pieces or keep juicing until the Pulp Bin overflows.
NutriBullet Juicer 800W 2.0
Stop using your NutriBullet Juicer 800W 2.0 if it seems unsafe; keep damaged parts out of use and seek support for a burning smell or electrical fault before restarting.
Has the Juicer 800W 2.0 stopped after overheating?
- For an ordinary overheat stop without damage, a burning smell or other electrical-fault signs, switch off, unplug and leave the motor to cool for at least 15 minutes.
- Before the next use, empty the Pulp Basin and clear the Sieve with the Cleaning Brush; start the motor before feeding and use only gentle pusher pressure. NEVER submerge the motor base in water.
- If the stop repeats with a smaller, properly prepared load, leave the juicer out of use for assessment.
Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: NutriBullet Cold Press Slow Juicer user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Juicer Pro 1000W user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Cold Press Batch Juicer user guide (PDF)
The full steps for this model are in its user guide: Magic Bullet Mini Juicer user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Juicer 800W 2.0 user guide (PDF)