Yes, where an accessory’s guide permits cold-water sterilising, but that permission does not cover heat sterilising or other parts. Check the permitted sterilising method for the exact accessory before using tablets, boiling water, steam or a dishwasher sanitise cycle.
What if the powered appliance is damaged or malfunctions?
If the powered appliance is damaged or malfunctions, stop using it, unplug it only if it is safe to do so, and take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).
If a step above directs you to our team, or you need help with an unresolved issue in this article, see our warranty article.
NutriBullet Ultra 1200
Do not sterilise NutriBullet Ultra 1200 parts with heat or boiling water.
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet 900 Series
Do not use dishwasher sanitise cycles for NutriBullet 900 Series cups. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 900 Essentials Set (AU and NZ)
Do not use dishwasher sanitise cycles for NutriBullet 900 Essentials Set cups. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 900 Mega Pack (AU and NZ)
Do not use dishwasher sanitise cycles for NutriBullet 900 Mega Pack cups. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 600 Series
Do not use dishwasher sanitise cycles for NutriBullet 600 Series cups. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet Ultra 1000 / Ultra 1000 Premium
Do not sterilise NutriBullet Ultra 1000 / Ultra 1000 Premium parts with heat or boiling water (NB07500-1008 only).
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
These steps cover Ultra 1000 Premium product code NB07500-1008 For another Ultra 1000 product code, follow the cleaning instructions supplied with that exact pack. Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet Select 1200 / 2.0 Select 1200
Do not use dishwasher sanitise cycles for NutriBullet Select 1200 / 2.0 Select 1200 cups.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
- Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
- Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place.
Can I use the sanitise cycle?
Do not use the dishwasher sanitise cycle for the cups; this heat can warp the plastic.Can I dismantle the blade?
Do not remove any components from the easy-twist extractor blade; dismantling can permanently damage it and cause leakage.NutriBullet Pro+ 1200 / Pro Plus 1200
Do not use dishwasher sanitise cycles for NutriBullet Pro+ 1200 / Pro Plus 1200 cups.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 2.0 Pro 1000 — New Zealand
Do not use dishwasher sanitise cycles for NutriBullet 2.0 Pro 1000 NB07100-1008DG — New Zealand cups.
The washing steps below clean the parts; they are not a sterilising procedure.
These instructions are for NB07100-1008DG in New Zealand.
Do not use the dishwasher sanitise cycle for the cups: the heat can warp the plastic.
Can I sterilise the parts of my personal blender?
- Switch off and unplug the motor base Wait until every moving part has stopped, then remove the cup and easy-twist extractor-blade assembly before cleaning.
- Wash cups and to-go lids on the dishwasher top rack, without the sanitise cycle Hand-wash the easy-twist extractor blade with soap and water.
- Dry the easy-twist extractor blade completely after every use. Check its underside for cracking or breakage and replace a damaged blade immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
Can I dismantle the blade?
Do not take apart the easy-twist extractor blade; this can permanently damage it and cause leakage.
NutriBullet 1000 Series
Do not use dishwasher sanitise cycles for NutriBullet 1000 Series cups (use these instructions only if they match the guide supplied with your product).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Use these instructions with the user guide that came with your blender For product code N10-0807DG, check the user guide that came with it before using a cleaning blend or dishwasher method. Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet Turbo 1000
Do not sterilise NutriBullet Turbo 1000 parts with heat or boiling water (NBT07400-1006AK only).
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
These steps cover Turbo 1000 product code NBT07400-1006AK For NBT07400-1004AW or NBT07400-1006AW, follow the guide supplied with that pack. Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet 1000 Mega Pack / 1000 Series Mega Pack
Do not use dishwasher sanitise cycles for NutriBullet 1000 Mega Pack / 1000 Series Mega Pack cups (N10-1107AK only).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
These steps cover the black 1000 Series Mega Pack, product code N10-1107AK. For another pack code, match the cleaning method to the guide supplied with it; use the Milling Blade steps only when that blade is included. Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 1200 Series / 12 Piece
Do not use dishwasher sanitise cycles for NutriBullet 1200 Series / 12 Piece cups (check your pack’s guide).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Use these 1200 Series care instructions only if they match your pack’s guide. For the 12 Piece pack, product code N12-1207C, check the user guide that came with it for the correct start control and accessory instructions. Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 1200 Series / 10 Piece
Do not use dishwasher sanitise cycles for NutriBullet 1200 Series / 10 Piece cups (check your pack’s guide).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Use these 1200 Series care instructions only if they match your pack’s guide. For the 10 Piece pack, product code N12-1007, check the user guide that came with it for the correct start control and accessory instructions. Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 2.0 Pro 1200
Do not use dishwasher sanitise cycles for NutriBullet 2.0 Pro 1200 cups.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
- Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
- Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place.
Can I use the sanitise cycle?
Do not use the dishwasher sanitise cycle for the cups; this heat can warp the plastic.Can I dismantle the blade?
Do not remove any components from the easy-twist extractor blade; dismantling can permanently damage it and cause leakage.NutriBullet 500 Series / 4 Piece
Do not use dishwasher sanitise cycles for NutriBullet 500 Series / 4 Piece cups (use these instructions only if they match the combined-series guide supplied with your product).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Use these 500 Series cleaning steps with the guide supplied with your blender For 4 Piece product codes NB5-0407DG and NB5-0407MAW, match the care instructions to the supplied pack guide. Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet 1000 Essentials McLaren
Do not use the dishwasher sanitise cycle for the cups, as it may warp the plastic. For extra disinfecting, rinse the washed extractor blade with a 10% vinegar and water solution or lemon juice.
How do I wash the cups and To-Go Lids?
- The cups and To-Go Lids are top-rack dishwasher safe. Rinse them and give them a quick brush first to remove dried food.
- You can also hand wash them in warm soapy water and rinse.
How do I disinfect the extractor blade?
- Keep the extractor blade out of the dishwasher. Hand wash it in warm soapy water and rinse.
- For extra disinfecting after washing, rinse it with a 10% vinegar and water solution or lemon juice.
- Do not remove the gasket; this permanently damages the blade and causes leakage. Dry both sides of the blade completely.
Can I use the microwave?
- No. Keep the cups, motor base and all accessories out of the microwave.
How do I clean the motor base?
- Unplug it first. Wipe it with a sponge or cloth dampened with warm soapy water. Never put the motor base in water.
NutriBullet 700 Series
Do not use dishwasher sanitise cycles for NutriBullet 700 Series cups.
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the extractor blade. Hand-wash the extractor blade with soap and water, scrub away food and rinse; keep the blade out of the dishwasher.
- Dry the blade. Turn the extractor blade on its side in a dish drainer and let both sides dry completely.
- Clean the motor base. With the base unplugged, wipe its inside and outside with a sponge or dish cloth dampened with warm soapy water until clean.
Which dishwasher cycle should I avoid?
Do not use the dishwasher sanitise cycle for the cups because the high heat can warp the plastic.Can I remove the blade gasket?
Leave the gasket inside the extractor blade; removing it permanently damages the blade and causes leakage.How can I give the washed blade an additional rinse?
After washing the blade, rinse it with a 10% vinegar/water solution or lemon juice if additional disinfecting is desiredWhat if the gasket is loose or damaged?
Stop using an extractor blade with a loose or damaged gasket and replace the complete extractor blade; do not fit a separate gasket.NutriBullet Select 1000 / Select 1000 with pitcher
Do not use dishwasher sanitise cycles for NutriBullet Select 1000 / Select 1000 with pitcher cups (NB07200-1007DG cup and blade only).
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Clean the blade. Carefully hand-wash the easy-twist extractor blade with soap and water immediately after use; use a small brush or sponge to dislodge stuck food and keep fingers away from its sharp edges.
- Dry and check the blade. Dry the easy-twist extractor blade completely after each use and inspect its underside for cracking or breakage; replace a loose, cracked or damaged blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
- Clear residue near the actuator system. Scrub the actuator area with a small brush while the base is unplugged; leave all motor-base pieces in place.
Can I use the sanitise cycle?
These steps cover the cup and blade of Select 1000 product code NB07200-1007DG For the Select 1000 with pitcher, product code NB07200-1006DG, use its supplied pitcher instructions. Do not use the dishwasher sanitise cycle for the cups; this heat can warp the plastic.Can I dismantle the blade?
Do not remove any components from the easy-twist extractor blade; dismantling can permanently damage it and cause leakage.NutriBullet Pro+ Matte Black
Include the full product code from the appliance label and the name of the part.
Can I sterilise the parts of my personal blender?
- Find the full product code on the appliance label.
- Check the user guide supplied with that product code for the care instructions while you wait for help.
NutriBullet 600 Essentials Kit
Do not use the dishwasher sanitise cycle for the cups, as it may warp the plastic. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
Include the full product code from the appliance label and the name of the part.
Can I sterilise the parts of my personal blender?
- Find the full product code on the appliance label.
- Check the user guide supplied with that product code for the care instructions while you wait for help.
NutriBullet Ultra 1200 McLaren / Club Pack
Do not sterilise NutriBullet Ultra 1200 McLaren / Club Pack parts with heat or boiling water (NB07500-1206GO-MC only).
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
These steps cover Ultra 1200 McLaren product code NB07500-1206GO-MC For Club Pack product code NB07500-1214S, follow the guide supplied with that pack. Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet Ultra 1200 Premium
Do not sterilise NutriBullet Ultra 1200 Premium parts with heat or boiling water.
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet Baby
Yes, use only a cold-water sterilising method for Baby accessories; hot-water and steam sterilisation are not permitted.
Can I sterilise the parts of my personal blender?
- Wash the blade attachment. Hand-wash the blade attachment. Do not put it in the dishwasher, remove its seal or expose the blade and plastic parts to rapid temperature changes, boiling water or steam. If the seal is removed, stop using that blade attachment and replace it. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
- Clean the Motor Base. With the Motor Base unplugged, wipe its accessible inside and outside with a damp cloth. NEVER submerge the motor base in water or other liquids. Never immerse the cord or plug in water or other liquids.
Can I sterilise Baby accessories?
Use only a cold-water sterilising method, such as antibacterial dissolvable steriliser tablets. Do not use hot-water or steam sterilisation; these can warp the plastic.Which parts can go in the dishwasher?
Put the cups and Batchbowl on the top dishwasher rack, or hand-wash them with warm, soapy water and rinse.Steriliser tablets are sold at most supermarkets and chemists.
NutriBullet Baby Steam + Blend
The washing steps below clean the parts; they are not a sterilising procedure.
Can I sterilise the parts of my personal blender?
- Wash the blade and holder. Rotate the bottom of the Blade Holder to remove it from the Work Bowl. Hand-wash the Blending Blade and Blade Holder in warm, soapy water, handling the sharp blade carefully, then dry them thoroughly.
- Clean the Motor Base. Wipe the entire Motor Base with a clean, damp cloth after every use.
Which parts can go in the dishwasher?
Before first use and before and after each use, wash the Work Bowl and Work Bowl Lid in warm, soapy water or on the dishwasher top shelf; dry them thoroughly. Keep the Motor Base, Blending Blade and Blade Holder out of the dishwasherNutriBullet Ultra Plus+ Compact Kitchen System
Do not sterilise NutriBullet Ultra Plus+ Compact Kitchen System parts with heat or boiling water.
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.Which processor parts can go in the dishwasher?
Put the Blades, Discs, Work Bowl and Work Bowl Lid on the dishwasher top rack only; never use the heat or sanitise cycle.Which processor parts must I wash by hand?
Keep the Processor Base and Blade Adapter out of the dishwasher and wash them by hand; alternatively hand-wash all Processor Attachment parts with a sponge or cloth, soap and water.Which grinder parts can go in the dishwasher?
Wash the Grinding Cup and Grinder Blade on the dishwasher top rack only, without the heat or sanitise cycle; alternatively hand-wash them with a sponge or cloth, soap and water.NutriBullet 600 Mega Pack
Do not use the dishwasher sanitise cycle for the cups, as it may warp the plastic. If you want extra disinfecting after washing, rinse the extractor blade with a 10% vinegar-and-water solution or lemon juice.
Include the full product code from the appliance label and the name of the part.
Can I sterilise the parts of my personal blender?
- Find the full product code on the appliance label.
- Check the user guide supplied with that product code for the care instructions while you wait for help.
NutriBullet Turbo 1000 Deluxe Set
Do not sterilise NutriBullet Turbo 1000 Deluxe Set parts with heat or boiling water.
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.NutriBullet Turbo Ultimate Pack
Do not sterilise NutriBullet Turbo Ultimate Pack parts with heat or boiling water.
Can I sterilise the parts of my personal blender?
- Clean the Rapid Extractor Blade. Rinse the Rapid Extractor Blade with warm soapy water immediately after use, then use a small brush or sponge dampened in soapy water to remove any residue.
- Wash the cups and To-Go Lids. Rinse or scrub food off the cups and To-Go Lids, then wash them on the dishwasher top rack.
- Clean the motor base. Clean the motor-base surface with a sponge or dishcloth dampened with soapy water and gently dry it with a clean cloth. NEVER submerge the motor base in water or other cleaning liquid.
Which dishwasher settings should I avoid?
Never put the Rapid Extractor Blade, cups or To-Go Lids on the bottom rack or use a heat or sanitise cycle; these conditions can warp the parts.Can I use heat to clean or sanitise parts?
Do not put any part or accessory in a microwave, conventional oven, air fryer or stovetop pot, or immerse it in boiling water to clean or sanitise it.Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: NutriBullet Ultra 1200 user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 900 Series user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 900 Essentials Set NB9-0807DG user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 900 Mega Pack NB9-1107AK user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 600 Series user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Ultra 1000 / Ultra 1000 Premium user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Select 1200 / 2.0 Select 1200 user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Pro+ 1200 / Pro Plus 1200 user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 2.0 Pro 1000 NB07100-1008DG user guide (NZ, PDF)
The full steps for this model are in its user guide: NutriBullet 1000 Series user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Turbo 1000 user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 1000 Mega Pack / 1000 Series Mega Pack user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 1200 Series / 12 Piece user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 1200 Series / 10 Piece user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 500 Series / 4 Piece user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 1000 Essentials McLaren user guide (PDF)
The full steps for this model are in its user guide: NutriBullet 700 Series user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Select 1000 / Select 1000 with pitcher user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Ultra 1200 McLaren / Club Pack user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Ultra 1200 Premium user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Baby user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Baby Steam + Blend user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Ultra Plus+ Compact Kitchen System user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Turbo 1000 Deluxe Set user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Turbo Ultimate Pack user guide (PDF)