Remove residue from portable-blender cups, lids and blades with the permitted washing or rinse-blend method, then wipe the powered base with a damp cloth. Keep water away from the charging connection.
NutriBullet Portable Blender / Portable Blender McLaren
Loosen residue in the NutriBullet Portable Blender / Portable Blender McLaren Cup with cold water and a drop of soap in one 20-second rinse blend, keeping the contents at or below MAX, then hand-wash the Cup and Lid.
How do I remove stuck-on residue from my portable blender?
- Loosen residue with a rinse blend. Add cold water and a drop of soap to the Cup, fit the Lid and blend for one 20-second cycle. Keep the contents at or below the MAX line and do not use hot or warm water.
- Stop and wash the Cup and Lid. Turn off, disconnect the charger and wait for the blades to stop; hand-wash the Cup and Lid with warm soapy water and rinse clean.
- Clean food around the blades. Gently rinse the blade assembly and wipe it with a damp sponge or cloth without touching the sharp edges. NEVER submerge the motor base in water or cleaning liquid. Never run the Motor Base under water.
- Wipe and dry the motor base. Gently wipe and dry the Motor Base with a clean cloth.
- Store it after cleaning. Keep the blender upright with the Cup attached over the blades and nothing stacked on top.
Can I put the parts in the dishwasher afterwards?
Only the Cup and Lid may go on the top rack, without heat or sanitise cycles; the Motor Base and fixed blade assembly must stay out.What should I inspect after washing?
Check the components periodically for damage and wear; stop using and replace damaged detachable parts. Do not let dust accumulate in the USB-C port or insert anything except the appropriate charger.NutriBullet Flip Stainless
Loosen stubborn residue in the NutriBullet Flip Stainless Blending Cup by leaving soapy water on each end for a few minutes, then run the 30-second cleaning cycle and repeat with fresh water only.
How do I remove stuck-on residue from my portable blender?
- Prepare to clean Flip. Disconnect the charger and leave NutriBullet Flip Stainless undisturbed for 90 seconds so it shuts down completely; check that the blades have stopped before taking parts apart.
- Prepare a cleaning blend. Rinse out the Blending Cup with fresh water, add a drop of dish soap and fill the cup halfway with water.
- Start the cleaning cycle. Secure the Motor Base, Blade, and Lid on the Cup with the Flip-Top Lid closed. Wake the blender with Power, then press Power again to start the 30-second cycle; flip and shake the blender to agitate the water.
- Rinse afterwards. When the cycle ends, open the Flip-Top Lid over the sip hole and empty the soapy water; repeat one cycle with fresh water only, without soap.
- Remove residue from small openings. After disconnecting the charger and allowing 90 seconds for shutdown, use the supplied Cleaning Brush on the straw, under the blades, the sip hole and the vent hole.
- Rinse the blade area and spout by hand. Cover the USB-C port with a thumb or finger; point the blade down at an angle to rinse only the blade area, then point it upwards to rinse the sip hole gently with warm water. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the whole Motor Base, Blade, and Lid.
- Dry the charging port. Wipe the Motor Base, Blade, and Lid and pat the USB-C port dry with a clean cloth. Stand the assembly upright with the Flip-Top Lid open and allow it to dry fully in a sunny area before charging; avoid excessive heat and keep within the guide’s recommended 10–40°C storage and charging range.
What if residue is stubborn?
Let the soapy water sit for a few minutes on each end of the Blending Cup before running the cleaning cycle.NutriBullet Flex Portable / Flex Portable McLaren
Remove residue from the NutriBullet Flex Portable / Flex Portable McLaren Blade Block, Blending Cup and Sip Lid with warm, soapy water and rinse clean; wipe food from the Motor Base with a damp cloth.
How do I remove stuck-on residue from my portable blender?
- Take Flex apart. Use these steps for NutriBullet Flex Portable NBPB07222 and Flex Portable McLaren Papaya NBPB07222PA-MC. Check the remaining charge on the LED Battery Bar, then turn the blender off and disconnect the charger. Gently twist the Cup and Blade Block off the Motor Base, holding the Cup and base without pushing down or gripping the Sip Lid. Twist the Blade Block clockwise to remove it, keeping clear of the blades; close the Sip Cap before twisting the Sip Lid with Carry Loop anticlockwise.
- Wash the detachable parts. Hand-wash the Blade Block with warm soapy water and rinse clean, taking care around its sharp blades. Wash the Blending Cup and Sip Lid with Carry Loop with warm soapy water, or put those two parts on the dishwasher top rack without a heat or sanitise cycle.
- Clean the motor base. Wipe food from the Motor Base with a damp cloth. Keep its Silicone Charge Port Cover in place. Never put the base in the dishwasher or run the motor base under water.
- Dry before reassembly. Dry the Blade Block completely before attaching it to the Cup. Fully dry the Sip Lid before blending or storage; air-dry with the Sip Cap open to avoid trapped moisture around the seal.
- Store Flex. Store upright with the Blade Block secured to the Blending Cup and the Sip Lid attached so the blades stay covered; do not stack objects on top.
What if the lid gasket moves during washing?
Remove excess moisture from the Sip Lid gasket area and gently guide a displaced gasket back into placeNutriBullet GO
Remove residue from the NutriBullet GO Cup and Lid by washing them with warm, soapy water and rinsing clean; gently rinse the blade assembly and wipe it with a damp sponge or cloth.
How do I remove stuck-on residue from my portable blender?
- Prepare GO for cleaning. Turn NutriBullet GO off and check that no light is on; wait for the motor and blades to stop before separating the cup.
- Wash the cup and lid. Place the Cup and Lid on the dishwasher top rack, or hand-wash them with warm soapy water and rinse.
- Clean the blades. Gently rinse the blade assembly and carefully wipe it with a damp sponge or cloth, without touching the sharp edges.
- Store GO. Keep all parts together in a safe place; screw the Blade Cover onto the Motor Base when it is not in use.
Can the blade assembly or motor base go in water?
Keep the blade assembly out of the dishwasher. Do not run the motor base directly under water.Still need help? Chat with us and give us your model name and product code.
The full steps for this model are in its user guide: NutriBullet Portable Blender / Portable Blender McLaren user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Flip Stainless user guide (PDF)
The full steps for this model are in its user guide: NutriBullet Flex Portable / Flex Portable McLaren user guide (PDF)
The full steps for this model are in its user guide: NutriBullet GO user guide (PDF)