Skip to main content

How can we help?

Which replacement parts fit my personal blender?

  • Updated

Compatible personal-blender replacements include the matching cups, lids, lip rings and complete extractor blade, plus a milling blade or pitcher where listed for the appliance’s full product code. A blade’s wattage label or a cup’s size alone is not a fit check.

Order genuine parts through Australian accessories or New Zealand accessories. Before changing or cleaning parts, switch off, unplug and wait for the motor to stop; keep fingers away from sharp blade edges.

Pick your machine in the drop-down menu on the accessories page to see which parts fit it.

NutriBullet Ultra 1200

Which parts fit my NutriBullet Ultra 1200?

These parts fit the NutriBullet Ultra 1200:

Only the genuine Ultra Rapid Extractor Blade has a separate 5-year limited warranty from delivery. It covers defects, not normal wear and tear. Ultra blade warranty terms.

What else should I know before buying parts?
  • Do not substitute the legacy NBM-BA041 1000/1200 W extractor blade; it does not fit Ultra.
  • For a smaller vessel, ANBC20TCDB is a 590 mL cup with lid that fits Ultra; its material differs from the Ultra-specific recycled-content cups.
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: at least every five years, depending on use; replace sooner if damage appears. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet 900 Series

Which parts fit my NutriBullet 900 Series?

These parts fit the NutriBullet 900 Series:

The 500/600/900/1000 Series user guide shows the Milling Blade used on the NutriBullet Cup. Check the exact product code on your appliance label before buying or using a milling blade.

Follow the cup and blade arrangement in the combined-series guide supplied with this model; check the product code on your own pack when ordering.

Which blade and cup should I choose?
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?

NutriBullet 900 Essentials Set (AU and NZ)

Which parts fit my NutriBullet 900 Essentials Set?

These parts fit the NutriBullet 900 Essentials Set:

Follow the cup and blade arrangement in the combined-series guide supplied with this model; check the product code on your own pack when ordering.

Which blade and cup should I choose?
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?

NutriBullet 900 Mega Pack (AU and NZ)

Which parts fit my NutriBullet 900 Mega Pack?

These parts fit the NutriBullet 900 Mega Pack:

Follow the cup and blade arrangement in the combined-series guide supplied with this model; check the product code on your own pack when ordering.

Which blade and cup should I choose?
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?

NutriBullet 600 Series

Which parts fit my NutriBullet 600 Series?

These parts fit the NutriBullet 600 Series:

Follow the cup and blade arrangement in the combined-series guide supplied with this model; check the product code on your own pack when ordering.

Which blade and cup should I choose?
  • Use Cross Blade NBM-BA031 for this model, and match the cup to the full product code before ordering. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  • For NBR-0507LG, identify the supplied 700 mL cup and extractor blade; check a replacement cup against the full 600 Series product code.
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?

NutriBullet Ultra 1000 / Ultra 1000 Premium

Which parts fit my NutriBullet Ultra 1000 / Ultra 1000 Premium?

These parts fit the NutriBullet Ultra 1000 / Ultra 1000 Premium:

  • NutriBullet Ultra Rapid Extractor Blade NutriBullet Ultra Rapid Extractor Blade, part code BDM-BA026CDB. Buy in Australia or New Zealand.
  • NutriBullet Premium Flip-Top Lids NutriBullet Premium Flip-Top Lids, part code ANBLID2CDB. Buy in Australia or New Zealand.
  • NutriBullet Ultra 700ml Cup with Lid NutriBullet Ultra 700ml Cup with Lid, part code ANBCTR24CDB. Buy in Australia or New Zealand.
  • NutriBullet Ultra 700ml Travel Cup with Lid NutriBullet Ultra 700ml Travel Cup with Lid (the handled 700 mL cup), part code ANBHCTR24CDB. Buy in Australia or New Zealand.
  • NutriBullet Ultra 900ml Cup with Lid NutriBullet Ultra 900ml Cup with Lid, part code ANBCTR32CDB. Buy in Australia or New Zealand.

Only the genuine Ultra Rapid Extractor Blade has a separate 5-year limited warranty from delivery. It covers defects, not normal wear and tear. Ultra blade warranty terms.

The guide steps here apply to Ultra 1000 Premium NB07500-1008; use the full product code for other Ultra 1000 packs.

What else should I know before buying parts?
  • Do not substitute the legacy NBM-BA041 1000/1200 W extractor blade; it does not fit Ultra.
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: at least every five years, depending on use; replace sooner if damage appears. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet Select 1200 / 2.0 Select 1200

Which parts fit my NutriBullet Select 1200 / 2.0 Select 1200?

These parts fit the NutriBullet Select 1200 / 2.0 Select 1200:

  • NutriBullet Easy Twist Blade NutriBullet Easy Twist Blade, part code BDM-BA002CDB. Buy in Australia or New Zealand.
  • NutriBullet 900ml Pitcher NutriBullet 900ml Pitcher, part code ANBP32CDB. Buy in Australia or New Zealand.
  • NutriBullet Premium Flip-Top Lids NutriBullet Premium Flip-Top Lids, part code ANBLID2CDB. Buy in Australia or New Zealand.
  • NutriBullet 2.0 500ml Short Cup NutriBullet 2.0 500ml Short Cup, part code BDM-VE014CDB. Buy in New Zealand.
  • NutriBullet 2.0 590ml Travel Cup NutriBullet 2.0 590ml Travel Cup, part code BDM-VE016CDB. Buy in New Zealand.
  • NutriBullet 2.0 700ml Handled Travel Cup NutriBullet 2.0 700ml Handled Travel Cup, part code BDM-VE011CDB. Buy in New Zealand.
  • NutriBullet 590ml Cup with Lid NutriBullet 590ml Cup with Lid, part code ANBC20TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Cup with Lid NutriBullet 700ml Cup with Lid, part code ANBC24TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Handled Cup with Lid NutriBullet 700ml Handled Cup with Lid, part code ANBHC24TCDB.
  • NutriBullet 900ml Cup with Lid NutriBullet 900ml Cup with Lid, part code ANBC32TCDB. Buy in Australia or New Zealand.

For Select 1200 / 2.0 Select 1200, match product code NB07200-1210DG.

Which supplied vessels should I match?
How do I fit and inspect the Easy-Twist parts?
  1. Screw the Easy-Twist Extractor Blade firmly onto the cup, invert it onto the Motor Base and twist clockwise until locked; do not force a cup whose thread will not align.
  2. Before use, check the gasket is completely seated and the blade underside has no cracking or breakage; replace the complete blade if it is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  3. Do not remove the gasket or any other blade components; the blade assembly must stay intact to seal correctly.
How do I clean and store Easy-Twist parts?
  1. Separate the cup and blade from the unplugged Motor Base; clean the blade immediately with soapy water and a small brush or sponge, then dry it fully.
  2. Rinse and briefly brush the cup and To-Go Lid, then hand-wash or place them on the dishwasher top rack; do not use the sanitise cycle.
  3. For stuck residue, fill an undamaged cup to MAX with water at 21°C or cooler and 1–2 drops of dish soap, attach its blade and blend for 20–30 seconds; scrub away the loosened food and rinse.
  4. Wipe the Motor Base with a warm soapy damp cloth or sponge and use a small brush around the actuator. Do not remove base components.
  5. Store upright with nothing on top and keep spare pieces safely together; never store an exposed blade directly on the Motor Base.
How do I fit and care for the Select 1200 pitcher?
  1. Screw the removable Easy-Twist Extractor Blade into the pitcher base until aligned and secure, then turn the pitcher clockwise onto the base; never use a pitcher that will not align with its blade.
  2. Press the Pitcher Lid into place and lock the vented cap before use; remove the lid only after the motor stops.
  3. Rinse and briefly brush the pitcher before washing it in the dishwasher without the sanitise cycle, or hand-wash with soap and water; hand-wash the tamper and scrub stubborn food with a brush or sponge.
  4. For dried food in the pitcher, add room-temperature water to MAX with 1–2 drops of dish soap, fit its lid and blend for 20–30 seconds before scrubbing and rinsing.
  5. Store the pitcher upright with its lid secured and nothing stacked on that lid; cover the blade with the pitcher or cup rather than leaving it exposed on the base.
  6. Inspect the pitcher body and twisting threads for cracking, crazing or breakage; stop using a damaged pitcher and replace it before blending again.

NutriBullet Pro+ 1200 / Pro Plus 1200

Which parts fit my NutriBullet Pro+ 1200 / Pro Plus 1200?

These parts fit the NutriBullet Pro+ 1200 / Pro Plus 1200:

Match NutriBullet Pro+ 1200 / Pro Plus 1200 product code N12-1007MK when ordering replacement parts.

How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not store a bare extractor blade on the base; cover the blade with its cup before putting the appliance away.
When does a blade need replacing?

NutriBullet Pro 1000 / 2.0 Pro 1000

Which parts fit my NutriBullet Pro 1000 / 2.0 Pro 1000?

These parts fit the NutriBullet Pro 1000 / 2.0 Pro 1000:

  • NutriBullet Easy Twist Blade NutriBullet Easy Twist Blade, part code BDM-BA002CDB. Buy in Australia or New Zealand.
  • NutriBullet Premium Flip-Top Lids NutriBullet Premium Flip-Top Lids, part code ANBLID2CDB. Buy in Australia or New Zealand.
  • NutriBullet 2.0 500ml Short Cup NutriBullet 2.0 500ml Short Cup, part code BDM-VE014CDB. Buy in New Zealand.
  • NutriBullet 2.0 590ml Travel Cup NutriBullet 2.0 590ml Travel Cup, part code BDM-VE016CDB. Buy in New Zealand.
  • NutriBullet 2.0 700ml Handled Travel Cup NutriBullet 2.0 700ml Handled Travel Cup, part code BDM-VE011CDB. Buy in New Zealand.
  • NutriBullet 590ml Cup with Lid NutriBullet 590ml Cup with Lid, part code ANBC20TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Cup with Lid NutriBullet 700ml Cup with Lid, part code ANBC24TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Handled Cup with Lid NutriBullet 700ml Handled Cup with Lid, part code ANBHC24TCDB.
  • NutriBullet 900ml Cup with Lid NutriBullet 900ml Cup with Lid, part code ANBC32TCDB. Buy in Australia or New Zealand.

For Pro 1000 / 2.0 Pro 1000, these guide steps apply to NB07100-1008DG; the parts codes also list NB07100-1007DG.

Which supplied vessels should I match?
  • Identify the two 700 mL cups, 590 mL travel cup, two To-Go Lids and Easy-Twist Extractor Blade on the NB07100-1008DG pack.
Which cup and blade system should I use?
  • Use only the specified Easy-Twist blade and cups for the full product code on the motor base; do not force an attachment that does not fit.
How do I fit and inspect the Easy-Twist parts?
  1. Screw the Easy-Twist Extractor Blade firmly onto the cup, invert it onto the Motor Base and twist clockwise until locked; do not force a cup whose thread will not align.
  2. Before use, check the gasket is completely seated and the blade underside has no cracking or breakage; replace the complete blade if it is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  3. Do not remove the gasket or any other blade components; the blade assembly must stay intact to seal correctly.
How do I clean and store Easy-Twist parts?
  1. Separate the cup and blade from the unplugged Motor Base; clean the blade immediately with soapy water and a small brush or sponge, then dry it fully.
  2. Rinse and briefly brush the cup and To-Go Lid, then hand-wash or place them on the dishwasher top rack; do not use the sanitise cycle.
  3. For stuck residue, fill an undamaged cup to MAX with water at 21°C or cooler and 1–2 drops of dish soap, attach its blade and blend for 20–30 seconds; scrub away the loosened food and rinse.
  4. Wipe the Motor Base with a warm soapy damp cloth or sponge and use a small brush around the actuator. Do not remove base components.
  5. Store upright with nothing on top and keep spare pieces safely together; never store an exposed blade directly on the Motor Base.

The new Easy Twist extractor blade does not work with old NutriBullet cups, and old NutriBullet cups and blades cannot be used on the NutriBullet Pro 1000.

NutriBullet 1000 Series

Which parts fit my NutriBullet 1000 Series?

These parts fit the NutriBullet 1000 Series:

How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet Turbo 1000

Which parts fit my NutriBullet Turbo 1000?

These parts fit the NutriBullet Turbo 1000:

The guide mapping covers Turbo 1000 NBT07400-1006AK; match the full code for other packs.

What else should I know before buying parts?
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly.
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: every 12–18 months, depending on use; replace sooner if damage appears.
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet 1000 Mega Pack / 1000 Series Mega Pack

Which parts fit my NutriBullet 1000 Mega Pack / 1000 Series Mega Pack?

These parts are listed in Australia for the NutriBullet 1000 Mega family. Match your full pack code before ordering:

These guide steps apply to the black 1000 Series Mega Pack N10-1107AK; match other colours by their full pack code.

What else should I know before buying parts?
  • For the 1000 Mega family, the AU Cross Blade listing names NBM-BA031; identify whether you need the extractor blade or the separate Milling Blade before ordering.
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?
  • Replace the extractor blade every six months depending on use, or sooner if it is damaged or performance requires it.

NutriBullet 1200 Series / 12 Piece

A compatible replacement-part code for the 1200 Series / 12 Piece pack N12-1207C is not identified in the available product information.

What should I match before ordering?
  • Use N12-1207C, the 1200 Series / 12 Piece pack code, when requesting a part; give the full code and a photo of the original piece instead of choosing a part by “1200 W” alone.
How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet 1200 Series / 10 Piece

Which parts fit my NutriBullet 1200 Series / 10 Piece?

These parts fit the NutriBullet 1200 Series / 10 Piece:

How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet 2.0 Pro 1200

Which parts fit my NutriBullet 2.0 Pro 1200?

These parts fit the NutriBullet 2.0 Pro 1200:

  • NutriBullet Easy Twist Blade NutriBullet Easy Twist Blade, part code BDM-BA002CDB. Buy in Australia or New Zealand.
  • NutriBullet Premium Flip-Top Lids NutriBullet Premium Flip-Top Lids, part code ANBLID2CDB. Buy in Australia or New Zealand.
  • NutriBullet 2.0 500ml Short Cup NutriBullet 2.0 500ml Short Cup, part code BDM-VE014CDB. Buy in New Zealand.
  • NutriBullet 2.0 590ml Travel Cup NutriBullet 2.0 590ml Travel Cup, part code BDM-VE016CDB. Buy in New Zealand.
  • NutriBullet 2.0 700ml Handled Travel Cup NutriBullet 2.0 700ml Handled Travel Cup, part code BDM-VE011CDB. Buy in New Zealand.
  • NutriBullet 590ml Cup with Lid NutriBullet 590ml Cup with Lid, part code ANBC20TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Cup with Lid NutriBullet 700ml Cup with Lid, part code ANBC24TCDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Handled Cup with Lid NutriBullet 700ml Handled Cup with Lid, part code ANBHC24TCDB.
  • NutriBullet 900ml Cup with Lid NutriBullet 900ml Cup with Lid, part code ANBC32TCDB. Buy in Australia or New Zealand.

For 2.0 Pro 1200, match product code NB07100-1208DG.

Which supplied vessels should I match?
  • Identify the 900 mL cup, 700 mL handled cup, 590 mL travel cup, two To-Go Lids and Easy-Twist Extractor Blade.
Which cup and blade system should I use?
  • Use only the specified Easy-Twist blade and cups for the full product code on the motor base; do not force an attachment that does not fit.
How do I fit and inspect the Easy-Twist parts?
  1. Screw the Easy-Twist Extractor Blade firmly onto the cup, invert it onto the Motor Base and twist clockwise until locked; do not force a cup whose thread will not align.
  2. Before use, check the gasket is completely seated and the blade underside has no cracking or breakage; replace the complete blade if it is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  3. Do not remove the gasket or any other blade components; the blade assembly must stay intact to seal correctly.
How do I clean and store Easy-Twist parts?
  1. Separate the cup and blade from the unplugged Motor Base; clean the blade immediately with soapy water and a small brush or sponge, then dry it fully.
  2. Rinse and briefly brush the cup and To-Go Lid, then hand-wash or place them on the dishwasher top rack; do not use the sanitise cycle.
  3. For stuck residue, fill an undamaged cup to MAX with water at 21°C or cooler and 1–2 drops of dish soap, attach its blade and blend for 20–30 seconds; scrub away the loosened food and rinse.
  4. Wipe the Motor Base with a warm soapy damp cloth or sponge and use a small brush around the actuator. Do not remove base components.
  5. Store upright with nothing on top and keep spare pieces safely together; never store an exposed blade directly on the Motor Base.

NutriBullet 500 Series / 4 Piece

Which parts fit my NutriBullet 500 Series / 4 Piece?

These parts fit the NutriBullet 500 Series / 4 Piece:

Check the exact product code on your appliance label before buying or using a milling blade.

Follow the cup and blade arrangement in the combined-series guide supplied with this model; check the product code on your own pack when ordering.

Which blade and cup should I choose?
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
When does a blade need replacing?

NutriBullet 1000 Essentials McLaren

Which parts fit my NutriBullet 1000 Essentials McLaren?

Check that a part fits your exact pack code N10-0807GO-MC before ordering:

What should I match before ordering?
  • Before buying the 700 mL cup with lip ring NBM-U0270CDB, ask for fit to N10-0807GO-MC specifically; a listing with only a series name is not enough to select the McLaren pack part.
How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet 700 Series

Use the 700 mL handled cup, extractor blade and To-Go Lid made for the 700 Series NB07150-0704 appliance.

Which pieces belong to the 700 Series?
  • Identify the 700 mL handled cup, extractor blade and To-Go Lid; request replacements specifically for the NB07150-0704 series, rather than another similarly shaped cup or blade.
How do I fit and inspect the cup and blade?
  1. Twist the extractor blade onto the cup until tightly sealed, invert the assembly and line up the cup tabs with the Motor Base; gently push and turn clockwise to engage.
  2. To remove the assembly, gently push and turn anticlockwise, wait for the motor to stop and lift the cup off before unscrewing the blade.
  3. Inspect all three cup tabs for cracking, crazing, breakage or rounding; stop using a cup with a damaged or missing tab and replace the cup.
  4. Check the blade gasket remains fully seated; never remove it or try to replace it separately. A loose or damaged gasket requires a complete extractor-blade replacement.
How do I care for replacement parts?
  1. Remove the cup/blade assembly from the unplugged base and separate the pieces before washing; clean cups and To-Go Lids by hand with warm soapy water or in the top dishwasher rack.
  2. Rinse and brush dried residue off the cups and lids before dishwashing; never use a sanitise cycle, which can warp plastic.
  3. Hand-wash the blade, leaving the gasket in place; for optional extra disinfecting, rinse with a 10% vinegar/water solution or lemon juice, then dry both sides completely with the blade resting on its side.
  4. For dried food in an undamaged cup, fill it about two-thirds with water at 21°C or cooler, attach the extractor blade and blend for 20–30 seconds; remove, lightly scrub and rinse.
  5. Unplug the Motor Base before wiping it inside and out with a sponge or cloth dampened with warm soapy water; use a small brush to clear sticky actuator tabs while unplugged, and leave its rubber and plastic liners in place.
  6. Keep the Motor Base and blade out of the dishwasher.NEVER submerge the motor base in water. Do not microwave accessories.
  7. Do not use the extractor blade as a storage lid on a cup of food; remove the blade after blending and use the guide’s plastic-wrap or foil covering for storage.
Which extra checks apply to the 700 Series blade?
  • Check that the blade rotates freely and that its gasket is neither missing nor damaged; replace it immediately if either check fails.
When does a blade need replacing?
  • Replace the extractor blade every six months depending on use, or sooner if it is damaged or performance requires it.

NutriBullet Select 1000 / Select 1000 with pitcher

For Select 1000 NB07200-1007DG, use the matching 900 mL cup, 700 mL handled cup, To-Go Lids and Easy-Twist Extractor Blade; this pack does not include a pitcher.

The NB07200-1007DG Select 1000 pack has cups and no pitcher; match a pitcher-equipped NB07200-1006DG separately.

Which supplied vessels should I match?
  • Identify the 900 mL cup, 700 mL handled cup, two To-Go Lids and Easy-Twist Extractor Blade for NB07200-1007DG; use the full code when ordering.
How do I fit and inspect the Easy-Twist parts?
  1. Screw the Easy-Twist Extractor Blade firmly onto the cup, invert it onto the Motor Base and twist clockwise until locked; do not force a cup whose thread will not align.
  2. Before use, check the gasket is completely seated and the blade underside has no cracking or breakage; replace the complete blade if it is loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  3. Do not remove the gasket or any other blade components; the blade assembly must stay intact to seal correctly.
How do I clean and store Easy-Twist parts?
  1. Separate the cup and blade from the unplugged Motor Base; clean the blade immediately with soapy water and a small brush or sponge, then dry it fully.
  2. Rinse and briefly brush the cup and To-Go Lid, then hand-wash or place them on the dishwasher top rack; do not use the sanitise cycle.
  3. For stuck residue, fill an undamaged cup to MAX with water at 21°C or cooler and 1–2 drops of dish soap, attach its blade and blend for 20–30 seconds; scrub away the loosened food and rinse.
  4. Wipe the Motor Base with a warm soapy damp cloth or sponge and use a small brush around the actuator. Do not remove base components.
  5. Store upright with nothing on top and keep spare pieces safely together; never store an exposed blade directly on the Motor Base.

NutriBullet Pro+ Matte Black

The Pro+ Matte Black N12-1207MK-C pack uses standard and handled 900 mL cups and an extractor blade; request replacements specifically against that pack code.

What should I match before ordering?
  • Identify the two standard 900 mL cups, additional handled 900 mL cup and extractor blade for N12-1207MK-C; request replacements against that Pro+ Matte Black pack code.
How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet 600 Essentials Kit

Which parts fit my NutriBullet 600 Essentials Kit?

These parts fit the NutriBullet 600 Essentials Kit:

What should I match before ordering?
  • Identify the extractor blade, two 700 mL cups, lip ring and flip-top lid in the NBR-0807AW Essentials Set.
  • The 700 mL cup with lip ring NBM-U0270CDB is listed for NBR-0807AW; use that code when replacing the cup-and-ring combination.
How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet Ultra 1200 McLaren / Club Pack

Which parts fit my NutriBullet Ultra 1200 McLaren / Club Pack?

These parts fit the NutriBullet Ultra 1200 McLaren / Club Pack:

Check the name on your blade or in your pack’s guide. Only a genuine Ultra Rapid Extractor Blade has the 5-year limited warranty from delivery; other blades do not. It covers defects, not normal wear and tear. Ultra blade warranty terms.

The guide mapping covers Ultra 1200 McLaren NB07500-1206GO-MC; identify Club Pack NB07500-1214S separately.

What else should I know before buying parts?
  • For the Ultra family, match Rapid Extractor Blade BDM-BA026CDB and cups ANBCTR24CDB (700 mL), ANBCTR32CDB (900 mL), or ANBHCTR24CDB (700 mL handled); check the pack code against the part listing before ordering.
  • Do not substitute the legacy NBM-BA041 1000/1200 W extractor blade; it does not fit Ultra.
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly.
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: at least every five years, depending on use; replace sooner if damage appears.
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet Ultra 1200 Premium

Which parts fit my NutriBullet Ultra 1200 Premium?

These parts fit the NutriBullet Ultra 1200 Premium:

Only the genuine Ultra Rapid Extractor Blade has a separate 5-year limited warranty from delivery. It covers defects, not normal wear and tear. Ultra blade warranty terms.

Match Ultra 1200 Premium product code NB07500-1208.

What else should I know before buying parts?
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly. Buy a replacement extractor blade (New Zealand).
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: at least every five years, depending on use; replace sooner if damage appears. Buy a replacement extractor blade (New Zealand).
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet Ultra Plus+ Compact Kitchen System

Use the blending cup and Rapid Extractor Blade, processor bowl and cutting attachments, or Grinding Cup and Grinder Blade specifically designed for Ultra Plus+ NB07550-1206.

Only the genuine Ultra Rapid Extractor Blade has a separate 5-year limited warranty from delivery. The grinder and chopping blades are not included in this 5-year cover. It covers defects, not normal wear and tear. Ultra blade warranty terms.

Match Ultra Plus+ Compact Kitchen System NB07550-1206 and name the blending, processor or grinder attachment.

Which Ultra Plus+ attachment needs a part?
  • For blending, identify the 900 mL cup, To-Go Lid and Rapid Extractor Blade; choose genuine parts specifically designed for Ultra Plus+.
  • For food processing, identify the Work Bowl, Work Bowl Lid, Food Pusher, Processor Base with Blade Adapter, Chopping Blade and reversible Slice/Shred Disc.
  • For grinding, identify the Grinding Cup and Grinder Blade; keep the grinder separate from the blending-cup and food-processor assemblies.
How do I refit the processor parts?
  1. Remove the Work Bowl Lid, slide the bowl over the Processor Base and Blade Adapter, then twist the bowl clockwise until it sits flush and locks.
  2. For chopping, lower the Chopping Blade onto the central shaft and press down; for slicing or shredding, fit the disc with the desired cutting face upward, nearly level with the bowl rim.
  3. Twist the assembled bowl clockwise onto the Motor Base until it clicks; align the lid arrows and lock the Work Bowl Lid so both the base and lid locks are engaged.
  4. Use only the supplied Food Pusher to move food through the chute; do not force food down or overload the chute.
How do I remove and clean processor replacements?
  1. After stopping, remove the Work Bowl Lid first, then turn the Work Bowl/Processor Base anticlockwise off the motor; grasp the central plastic knob to lift out the blade or disc before removing the food.
  2. Wash the blades, disc, Work Bowl and lid on the dishwasher top rack or by hand with soap and water; hand-wash the Processor Base and Blade Adapter and avoid the heat/sanitise cycle.
  3. Soak stubborn residue on the blade or disc in room-temperature water with 1–2 drops of dish soap for 20–30 seconds, then carefully scrub clear without touching cutting edges.
  4. For storage, fit the Blade Adapter and Chopping Blade inside the bowl; place the disc in its lower storage position without aligning its marks with the adapter marks, then attach the lid.
How do I care for the grinder replacement?
  1. Use the grinder only for dry coffee or spices; never add liquid or ice, and do not use it as a storage container in the fridge or freezer.
  2. Wash the grinder attachment on the dishwasher top rack without a heat/sanitise cycle, or by hand; keep the Motor Base out of the dishwasher.
How do I protect all Ultra Plus+ parts?
  1. Inspect attachments for damage and stop using damaged parts; keep blades covered and never leave an exposed blade or disc directly on the Motor Base.
  2. Wipe the Motor Base with a damp sponge or cloth. Keep all attachments out of the microwave, oven, air fryer and stovetop.
How do I fit the Ultra Plus+ blending cup?
  1. Secure the Rapid Extractor Blade tightly onto the cup, then invert and twist clockwise onto the Motor Base until it clicks; detach only after the blade stops.
How do I clean the Ultra Plus+ blending cup and blade?
  1. Rinse the blade immediately with warm soapy water and scrub residue with a small brush or sponge; rinse cups and To-Go Lids before top-rack dishwashing with no heat/sanitise cycle.
  2. For dried food, fill the cup to MAX with room-temperature water and 1–2 drops of dish soap, refit the blade and blend for 20–30 seconds, then scrub and rinse.
How do I inspect the Ultra Plus+ blending cup and blade?
  1. Replace a cup or Work Bowl that is cracked, cloudy, warped or damaged; replace a Rapid Extractor Blade that will not rotate freely or has a missing or damaged gasket. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
  2. Keep Motor Base ventilation openings clean and unobstructed, and never put cups or attachments in the freezer or boiling water.
How do I attach and store the Ultra Plus+ grinder?
  1. Secure the Grinding Cup onto the Grinder Blade, place the complete attachment on the base and turn clockwise until it clicks; never place a partially assembled blade on the base.
  2. When grinding stops, twist the attachment anticlockwise off the base; turn the Grinding Cup clockwise to open it, and clean all components after each use.
  3. Store the blender and grinder in a dry, cool, clean place with the power cord safely tucked away and no blade exposed.
Which blade should I use for dry ingredients?
  • Keep dry grinding to the Coffee & Dry Spice Grinder; do not grind grains, cereal or coffee with the processor Chopping Blade or Slice/Shred Disc.
How do I separate the Work Bowl from its Processor Base?
  1. To separate the Work Bowl from its Processor Base and Blade Adapter, hold the base underneath, turn the bowl handle anticlockwise and lift the bowl off.

NutriBullet 600 Mega Pack

Which parts fit my NutriBullet 600 Mega Pack?

These parts fit the NutriBullet 600 Mega Pack:

What should I match before ordering?
  • Identify the 500 mL and 700 mL cups, extractor blade and separate milling blade in the 600 Mega Pack; state your full NBR-1107 product code when ordering.
  • For a 700 mL cup with lip ring, match part NBM-U0270CDB to your 600 Mega Pack product code.
How can I avoid ordering the wrong part?
  1. Record the full product code and match both the appliance and the required piece in the parts listing. Only order a part whose listing names your full product code.

NutriBullet Turbo 1000 Deluxe Set

Which parts fit my NutriBullet Turbo 1000 Deluxe Set?

These parts fit the NutriBullet Turbo 1000 Deluxe Set:

Match Turbo 1000 Deluxe Set NBT07400-1008.

What else should I know before buying parts?
  • Choose Turbo Rapid Extractor Blade BDM-BA034CDB; match the full product code before ordering.
  • Identify the supplied 590 mL, 700 mL and 900 mL cups; the 700 mL cup-and-lid accessory is ANBC24TCDB and the 900 mL cup-and-lid accessory is ANBC32TCDB.
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly.
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: every 12–18 months, depending on use; replace sooner if damage appears.
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

NutriBullet Turbo Ultimate Pack

Which parts fit my NutriBullet Turbo Ultimate Pack?

These parts fit the NutriBullet Turbo Ultimate Pack:

  • NutriBullet Turbo Rapid Extractor Blade NutriBullet Turbo Rapid Extractor Blade, part code BDM-BA034CDB. Buy in Australia or New Zealand.
  • NutriBullet 700ml Cup with Lid NutriBullet 700ml Cup with Lid, part code ANBC24TCDB. Buy in Australia or New Zealand.
  • NutriBullet 900ml Cup with Lid NutriBullet 900ml Cup with Lid, part code ANBC32TCDB. Buy in Australia or New Zealand. For the NBT07400-1009AK and NBT07400-1009SG packs only; check your full product code.

Match Turbo Ultimate Pack NBT07400-1009AK, NBT07400-1009SB or NBT07400-1009SG.

What else should I know before buying parts?
  • Choose Turbo Rapid Extractor Blade BDM-BA034CDB; match the full product code before ordering.
  • Match the 700 mL cup-and-lid accessory to ANBC24TCDB; for the NBT07400-1009AK and NBT07400-1009SG pack subset, the 900 mL cup-and-lid accessory is ANBC32TCDB.
How do I fit and inspect the Rapid Extractor Blade?
  1. Twist the Rapid Extractor Blade onto the cup until sealed, invert the cup onto the Motor Base and turn clockwise until it clicks; turn anticlockwise to unlock only after blending stops.
  2. Check the cup for cracks, cloudiness, warping or damage; replace a damaged cup rather than forcing the blade onto it.
  3. Check that the Rapid Extractor Blade rotates freely and its gasket is present and intact; stop using a damaged or restricted blade and replace the complete assembly.
  4. Inspect the blade regularly and follow the guide’s replacement recommendation: every 12–18 months, depending on use; replace sooner if damage appears.
How do I clean and store Rapid Extractor parts?
  1. Detach the cup and blade from the unplugged Motor Base; rinse the blade with warm soapy water immediately after use and remove residue with a small soapy brush or sponge.
  2. Rinse or scrub cups and To-Go Lids, then wash on the dishwasher top rack; never use the bottom rack or a heat/sanitise cycle for the blade, cups or lids.
  3. For stuck food in an undamaged cup, fill to MAX with room-temperature water and 1–2 drops of dish soap; refit the blade, blend for 20–30 seconds, then scrub and rinse.
  4. Wipe the base with a sponge or cloth dampened with soapy water, brush the actuator system and keep its ventilation clear.
  5. Keep parts out of the microwave, oven, air fryer and stovetop pot, and do not boil them to clean or sanitise them.
  6. Store the blender upright with no objects on top; put accessories somewhere safe and never leave a bare blade on the Motor Base.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: NutriBullet Ultra 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Essentials Set NB9-0807DG user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Mega Pack NB9-1107AK user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 600 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1000 / Ultra 1000 Premium user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Select 1200 / 2.0 Select 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Pro+ 1200 / Pro Plus 1200 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Pro 1000 / 2.0 Pro 1000 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo 1000 user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 1000 Mega Pack / 1000 Series Mega Pack user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 500 Series / 4 Piece user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 700 Series user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Select 1000 / Select 1000 with pitcher user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1200 McLaren / Club Pack user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra 1200 Premium user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Ultra Plus+ Compact Kitchen System user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo 1000 Deluxe Set user guide (PDF)

The full steps for this model are in its user guide: NutriBullet Turbo Ultimate Pack user guide (PDF)

Related articles

Contact us