• Inspect the NutriBullet Immersion Blender 800W blending arm, S-blade and whisk for damage or wear; their structure must be intact and their moving parts must turn freely.
• Stop using a damaged attachment and replace it with one designed for the exact NutriBullet Immersion Blender 800W; do not swap attachments from another model.
• Detach the motor body before checking an attachment. The blending arm is one single part: do not dismantle it to replace an internal blade.
• Fit a replacement S-blade on the chopping bowl centre pin by its upper plastic section and press down; lock the lid clockwise and push and turn the motor body clockwise onto it.
• For a replacement blending arm, insert the motor body into the arm, push down and turn clockwise until locked.

• Release the power button and wait for movement to stop; unplug before working near the blade, then reduce a very thick load or add suitable liquid to loosen the mixture.
• Check the cutting area for food residue; rinse away buildup with warm water before reassembling and retrying.
• If it still will not operate, disconnect, disassemble and reassemble the attachment so it locks tightly to the motor body; continued failure needs support rather than forcing the blade. NEVER submerge the main unit in water.

1. Wash the removable chopping blade and bowl in warm soapy water or the dishwasher, keeping hands away from sharp edges.
2. Hand-clean the blending arm, whisk holder and chopping bowl lid; do not soak these geared parts or put them in the dishwasher.
3. Clean after every use with no metal sponge; for dried food on the removable chopping blade, the guide permits a 30-minute hot-water soak to soften residue.
4. Let the attachments dry thoroughly and store them safely in a dry place where they will not be damaged.

• Inspect the NutriBullet Food Processor Chopping Blade, Dough Blade, thin and thick Slice/Shred Discs, Spiralizer Disc and Blade Adaptor for damage or wear; stop using and replace a damaged attachment.
• Check that the blades can rotate freely and that the structure is intact; do not keep running a damaged or obstructed assembly.
• Use only the bowl and blade attachments designed for the NutriBullet Food Processor.
• Push the Blade Adaptor onto the Work Bowl shaft; place a Chopping or Dough Blade at the bottom, or align a Slice/Shred Disc with the adaptor marks in the higher working position.
• For the Spiralizer, align its notches with the bowl tabs and FRONT towards the front; lock the lid clockwise with aligned arrows and turn the bowl onto the base until it clicks.

• If food lodges in the Feed Chute, stop and disconnect the processor, wait for the blade to stop, unlock the lid and remove the trapped food with the Food Pusher, spatula or spoon.
• If processed food has risen to just below the disc, empty the Work Bowl before processing more; a full bowl can block food movement.
• Keep rinds, pits, seeds, non-food items and ice out of the processor; these can damage the attachments.

1. Detach the cutting attachments and Blade Adaptor; wash after each use with warm soapy water or on the top dishwasher rack.
2. Do not use the sanitise cycle, steel wool or other hard abrasive cleaning materials; these may warp or scratch parts.
3. For storage, place the adaptor on the central shaft, then Chopping Blade, Dough Blade and discs; place discs in the lower storage position with their alignment marks apart.
4. Choose either both Slice/Shred Discs or one Slice/Shred Disc plus the Spiralizer Disc; all discs will not fit together. Place the Spiralizer last with FRONT facing forward, then lock the lid and insert the pusher.

• Before every use, inspect the NutriBullet Chill Blade Block for damage and the Pint Cup for cracks; stop using damaged components and obtain the correct genuine replacement.
• After processing, hold the blade-holder assembly by its plastic grip, not the Blade, Shaft or Blade Cover; if the shaft feels warm, cool it under running cool water before handling.
• Never carry the cup assembly by the Blade Shaft; support the Pint Cup and Blade Block with both hands.

• First remove the stopped cup assembly and pull the Blade Shaft back until the Blade rests against the top of the Blade Block; gently reinstall it so the blade does not pop out of position.
• For a blockage or improper load, remove the stopped assembly, clear remaining mixture and reset the blade; reinstall and use the centre/home button when prompted.
• Keep the recipe between MIN and MAX, fully frozen; do not process ice, loose frozen fruit, loose nuts or candy, thawed liquid, or an empty Pint Cup.

1. Remove the Blade from the Blade Block before top-rack dishwashing, or hand-wash the Blade, Block and Shaft in warm soapy water.
2. Use a sponge and dish soap around the circular Blade Block opening and shaft; avoid sanitise cycles, steel wool and abrasive cleaners.
3. Clean after every use and dry the Blade Shaft inside and out before installing it in the motor base.
4. Store with the Blade Cover attached or with the blade fitted to the Pint Cup; if a stored Blade Block has engaged in the base, turn it counter-clockwise to release before lifting it out.

• Inspect the NutriBullet Limitless Food Processor Chopping Blade, Reversible Slice/Shred Disc, adaptor and Slinger Disc for wear or damage; stop using any damaged component and obtain the correct genuine part.
• Use only blades, bowls and cups designed for the NutriBullet Limitless Food Processor.
• Fit the Chopping Blade down the Blade Adaptor to the bowl bottom, or secure the Reversible Slice/Shred Disc with its selected side up; run only one cutting attachment at a time.
• Lock the lid clockwise with its markings aligned to the handle, then turn the bowl clockwise on the base until it clicks.

• If food is caught in the Feed Chute, stop and unplug, wait for movement to stop, unlock the lid and clear the blockage with the pusher, spatula or spoon.
• If food reaches just below the disc in the Work Bowl, empty the bowl before continuing; do not force more food through the chute.
• Use gentle pressure on the Food Pusher; remove fruit rinds and pits, keep non-food items out, and do not grind dry grains or coffee or crush ice.

1. Lift blades and discs by the plastic grip or centre hub; remove them before taking food out and never tip them into your hand.
2. After each use, detach and wash the blade, disc, adaptor, Slinger Disc and Endless Chute by hand in warm soapy water or on the top dishwasher rack, up to 82°C.
3. Avoid heat/sanitise cycles, steel wool and hard abrasives.
4. For storage, lower the Chopping Blade onto the adaptor and the reversible disc above it, then lock the Work Bowl Lid and insert the Food Pusher.
5. Store the Endless Chute and Slinger Disc separately and keep all cutting edges covered.

• Inspect the NutriBullet Baby extractor blade before every use and replace it every six months for optimal performance, or sooner if loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Leave the seal in the blade housing. If it has been removed or is worn, torn or loose, stop using the attachment and replace the complete blade. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Use only the matching NutriBullet Baby attachment; do not substitute a blade intended for another appliance.

1. Hand-wash the blade with warm soapy water; do not put it in the dishwasher, where hot water can damage the outer-rim seal.
2. Do not boil or steam-sterilise the blade or expose it to rapid extreme temperature changes; the guide permits cold-water sterilisation options instead.
3. For stuck food in an undamaged cup/blade assembly, fill the cup halfway with soapy water, twist on the blade and blend for 10–20 seconds; switch off, unplug, untwist, lightly scrub and rinse.
4. Hand-tighten the extractor blade onto the Short Cup or Batchbowl and check that it is aligned before fitting the vessel to the motor base.
5. Replace the blade with a suitable lid for storing a blend, and never leave an exposed extractor blade on the motor base.

• Inspect the NutriBullet Baby Steam + Blend before each use; stop using and replace a damaged Blending Blade with the matching part.
• Do not process hard fruits or vegetables, citrus rinds, pits or seed stones; these can damage the blade and motor.

1. After steaming, allow at least ten minutes for cooling and wait until the blade and motor stop; unplug before disassembly and let hot parts cool completely before cleaning.
2. Lift out the Blending Blade by a non-sharp area; hand-wash it and the Blade Holder in warm soapy water, rinse and dry thoroughly.
3. Rotate the bottom of the Blade Holder to remove it from the Work Bowl for cleaning; clear the inside of the Blade Stem of food and water and dry it fully.
4. Clean promptly after each use so minerals and food residue do not build up; soak a detached part with dried food in hot water for 30 minutes, then remove the loosened residue.
5. Keep the Blending Blade and Blade Holder out of the dishwasher; refit the blade vertically onto the central Blade Holder so it is secure.
6. Keep the assembled parts together in a safe, dry, cool place when storing the appliance.

• Check the NutriBullet Ultra Plus+ Compact Kitchen System Chopping Blade, Reversible Slice/Shred Disc and Coffee & Dry Spice Grinder before use; stop using damaged parts and obtain genuine matching replacements.
• Check the Rapid Extractor Blade separately; stop use if it does not rotate freely or its gasket is missing or damaged.
• Do not substitute an aftermarket blade assembly; use the replacement-help route for a damaged attachment.

• For poor chopping, refit the Blade Assembly and Chopping Blade, reduce ingredients below MAX, and use ingredients suitable for chopping.
• For poor slicing or shredding, face the desired function upwards and align the disc and adaptor hash marks; the disc should sit nearly flush with the bowl rim.
• Keep the Feed Chute uncrowded, start the processor before feeding, and let food move down naturally under gentle Food Pusher pressure.
• If coffee or spices are unevenly ground, use short pulse grinding with the Dashed Circle; keep the Grinder below MAX with dry or dehydrated ingredients only, no liquid or ice.

1. Stop processing, wait for the blade or disc to stop completely and unplug the Motor Base.
2. Unlock and remove the Work Bowl Lid first; the Work Bowl cannot disengage while the lid is fitted.
3. Turn the Work Bowl and Processor Base anticlockwise and lift them off the Motor Base.
4. Grasp the cutting attachment by its central plastic knob and gently lift it out before removing food from the bowl.
5. Wash blades, discs, bowl and lid by hand or on the top dishwasher rack; hand-wash the Processor Base and Blade Adapter only.

Next steps

1. For stuck residue on processor blades or discs, immerse them in room-temperature water with one or two drops of dish soap for 20–30 seconds, then scrub the loosened food away.
2. Wash the separated Grinding Cup and Grinder Blade on the top dishwasher rack or by hand with a sponge or cloth, soap and water; avoid all heat/sanitise cycles.
3. Store the processor Chopping Blade and Disc inside the Work Bowl; lower the disc with its marks apart from the adaptor marks, then attach the lid.
4. Store the Grinder clean in a cool, dry place, never as a food-storage container or in the refrigerator/freezer; do not leave exposed blades on the motor base.