• Replace the Rapid Extractor Blade at least every five years, depending on use, or at the first signs of wear and tear. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

• Replace the Rapid Extractor Blade at least every five years, depending on use, or at the first signs of wear and tear. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Also inspect the pitcher and its twisting threads for cracking, crazing or breakage; replace a damaged pitcher rather than continuing with its blade assembly.
• Do not use a pitcher that does not align properly with its blade; correct the assembly before use and replace damaged parts. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.
4. Rinse and brush food from the pitcher before dishwasher cleaning, or hand-wash it with soap and water; keep fingers away from its blades and never use the sanitise cycle.
5. For food stuck in an undamaged pitcher, fill it to MAX with water at 21°C or cooler and one or two drops of dish soap, attach its lid and blend for 20–30 seconds; stop and unplug before scrubbing.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.
3. Store the pitcher upright with its lid fitted and nothing resting on the lid; keep the other parts in a safe place.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.
5. Inspect the blade before every use; when adding crushed ice, keep it to no more than one-quarter of the cup volume and include liquid up to the MAX line.

These blade instructions apply only to NutriBullet 2.0 Pro 1000 product code NB07100-1008DG in New Zealand; for another edition, use the user guide that came with it and include the full product code in your replacement enquiry.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.

• Replace the extractor blade after six months or as needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the blade seal is worn, torn, loose, dislodged or damaged, stop using the blade and replace the entire blade attachment. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Do not remove the gasket or try to replace it separately; it is part of the complete blade assembly.

• Replace the Rapid Extractor Blade every 12–18 months, depending on use, or at the first signs of wear and tear.
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement.

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance.
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged.
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.
5. Inspect the blades before each use; do not repeatedly crush ice or other hard ingredients without liquid because this can dull or damage them.

• Replace the extractor blade after six months or as needed for best performance.
• If the blade seal is worn, torn, loose, dislodged or damaged, stop using the blade and replace the entire blade attachment.
• Do not remove the gasket or try to replace it separately; it is part of the complete blade assembly.

• Replace the extractor blade after six months or as needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the blade seal is worn, torn, loose, dislodged or damaged, stop using the blade and replace the entire blade attachment. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Do not remove the gasket or try to replace it separately; it is part of the complete blade assembly.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

The guide recommends replacing the extractor blade about every six months for best performance. Replace it sooner if it becomes loose or damaged; inspect it before each use. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

Check that the gasket is completely seated before use, without removing it. If it is loose, missing or damaged, stop using that blade and replace the complete extractor blade assembly. Do not buy a loose ring to refit yourself. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

Quote the complete McLaren product code N10-0807GO-MC when requesting the correct extractor blade. Do not select another model’s blade by appearance alone.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance.
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged.
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.
• Inspect the extractor blade for free rotation and a present, undamaged gasket; stop using it and replace it if the blade cannot rotate freely or the gasket is missing.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.
5. Do not use the extractor blade to grind dry grain, cereal or coffee, and remove utensils before blending.

Use these blade-care instructions for product code NB07200-1007DG; include the full code when requesting a replacement for NB07200-1006DG. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Inspect the pitcher and its twisting threads for cracks, crazing or breakage; replace a damaged pitcher and never use it if it fails to align with its blade.

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.
4. Rinse and scrub the pitcher before dishwasher washing, or hand-wash with soap and water; avoid the sanitise cycle and keep fingers away from its sharp blade.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.

• Replace the extractor blade every 6 months (depending on use) or as needed for best performance.
• Check the gasket is fully seated before each use. If the seal is damaged, replace the complete blade assembly.
• If the gasket becomes loose or damaged over time, replace the extractor blade.
• Inspect the blades before each use.

• Do not remove the gasket. This permanently damages the extractor blade and causes leaks.
• Never run it without liquid or with an empty cup, as this may damage the blade.
• Do not crush ice or other hard items without liquid. Over time this can dull or damage the blades.
• The extractor blade is not one of the dishwasher pieces. Hand-wash it in warm soapy water and dry both sides completely.

• Check the 3 tabs on the side of the cup regularly for cracking, crazing, breakage or rounding. Never use a cup with a broken, damaged or missing tab.

• For the NutriBullet Pro+ Matte Black, see our warranty article for a blade check before choosing a replacement.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance.
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged.
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

The instructions below apply to McLaren product code NB07500-1206GO-MC. For Club Pack NB07500-1214S, include that complete pack code when asking for blade advice.

• Replace the Rapid Extractor Blade at least every five years, depending on use, or at the first signs of wear and tear.
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement.

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the Rapid Extractor Blade at least every five years, depending on use, or at the first signs of wear and tear. Buy a replacement extractor blade (New Zealand).
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement. Buy a replacement extractor blade (New Zealand).

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the single-serve Extractor Blade at least every six months, depending on use; stop sooner if it is damaged or will not rotate freely. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Check the Extractor Blade gasket; do not use the blade if the gasket is missing or damaged.
• Inspect the pitcher, cup, Work Bowl, chopping blade, dough blade, disc and adapter for damage or wear; stop using damaged parts and arrange the matching replacement.

1. Switch off, unplug and wait until the motor stops; detach the cup, pitcher or Work Bowl before changing or cleaning attachments.

1. Clean the Extractor Blade immediately using a small brush or sponge dampened with soapy water, keeping your fingers away from the cutting edges.
2. Remove the blade attachments, discs and Blade Adapter from the Work Bowl before washing; rinse or scrub them first, then wash the dishwasher-safe attachments without a heat or sanitise cycle.
3. Hand-wash the pitcher with soap and water or use the dishwasher; take care around its fixed blades and never boil or heat-sanitise any part.
4. For residue on an undamaged cup or Extractor Blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap; blend for 20–30 seconds, stop, unplug and scrub away the residue.
5. For residue in an undamaged pitcher, fill it halfway with water and one or two drops of dish soap; blend for 20–30 seconds, then stop, unplug and wash it.

1. Store the processor tools in the Work Bowl in this order: Blade Adapter, Chopping Blade, Dough Blade and Slice/Shred Disc; fit the lid to cover the sharp tools.
2. Store the system upright with nothing on top, and never leave blades or discs exposed.

The instructions below apply to NBF07500-1210DG. For a Blender Combo 1200 or other pack, include its full product code when requesting replacement advice.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately.
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Also inspect the pitcher and its twisting threads for cracking, crazing or breakage; replace a damaged pitcher rather than continuing with its blade assembly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
• Do not use a pitcher that does not align properly with its blade; correct the assembly before use and replace damaged parts. Buy a replacement pitcher (Australia) or pitcher (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.
4. Rinse and brush food from the pitcher before dishwasher cleaning, or hand-wash it with soap and water; keep fingers away from its blades and never use the sanitise cycle.
5. For food stuck in an undamaged pitcher, fill it to MAX with water at 21°C or cooler and one or two drops of dish soap, attach its lid and blend for 20–30 seconds; stop and unplug before scrubbing.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.
3. Store the pitcher upright with its lid fitted and nothing resting on the lid; keep the other parts in a safe place.

• Inspect the blade regularly. If the blades are damaged or do not rotate freely, stop using it immediately.
• If the blade becomes loose or damaged over time, replace it.
• Also check the pitcher. Do not use it if you see cracking, cloudiness or other damage.

• Switch off, unplug and wait until the blade has completely stopped before handling it.
• The blades are sharp. Handle them with care.
• Do not remove any part of the blade. This can permanently damage it and cause leaks.

• Non-food items and hard ingredients may damage the blades. Remove all utensils before blending.
• Do not grind dry ingredients such as grains, cereal or coffee. This may overheat the motor or damage the blades.
• Use only genuine nutribullet replacement parts.

• For the NutriBullet SmartSense Blender, see our warranty article for a blade check before choosing a replacement.

• Replace the Extractor Blade every 6 months, or as needed depending on how much you use it.
• Check the blade regularly. If the blades do not rotate freely or are damaged, stop using it immediately.
• If the Extractor Blade becomes loose or damaged over time, order a new Extractor Blade.

• Never remove the blade gasket/seal; it is not a removable part. If it has been removed or dislodged, replace the blade before using the blender again. If the gasket is missing or damaged, stop using the blade.
• Do not remove any parts of the Extractor Blade; this can permanently damage it and cause leaks. Use only genuine nutribullet replacement parts; aftermarket parts may damage the blender or create safety hazards.

• For the NutriBullet SmartSense Blender Combo, see our warranty article for a blade check before choosing a replacement.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance.
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately.
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks.
• Also inspect the pitcher and its twisting threads for cracking, crazing or breakage; replace a damaged pitcher rather than continuing with its blade assembly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.
4. Rinse and brush food from the pitcher before dishwasher cleaning, or hand-wash it with soap and water; keep fingers away from its blades and never use the sanitise cycle.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.
3. Store the pitcher upright with its lid fitted and nothing resting on the lid; keep the other parts in a safe place.

• Inspect the pitcher blades regularly; stop using the pitcher if the blades are damaged or no longer turn smoothly or freely.
• Check the pitcher for cracks, cloudiness or other damage and replace it if damaged; never use a pitcher that does not fit the motor base correctly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).

1. Turn off, unplug and wait until all moving parts stop, then remove the pitcher from the motor base before inspecting or washing it.

1. Rinse and scrub the pitcher with a dish brush before dishwasher cleaning, or hand-wash with soap and water; use a brush or sponge for stuck food without touching the sharp edges.
2. Avoid the sanitise cycle because high heat can warp the pitcher.

1. Do not run an empty pitcher or crush ice alone; include sufficient liquid and avoid overloading so the blade can turn.
2. Turn off and unplug before adjusting ingredients, use a long spoon or silicone or wooden utensil rather than a sharp metal object, and remove it before restarting.
3. Store the pitcher upright with its lid on, no objects on top and the blade covered.

• Replace the easy-twist extractor blade every six months, depending on use, or sooner when needed for best performance. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Before every use, check the gasket is completely seated in the blade; a damaged seal requires a complete replacement blade assembly.
• Regularly inspect the underside of the blade housing for cracking or breakage; stop using a damaged blade and replace it immediately.
• Replace an easy-twist extractor blade that becomes loose or damaged; do not remove any blade components to try to repair it, as this can permanently damage the assembly and cause leaks. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Also inspect the pitcher and its twisting threads for cracking, crazing or breakage; replace a damaged pitcher rather than continuing with its blade assembly. Buy a replacement pitcher (Australia) or pitcher (New Zealand).
• Do not use a pitcher that does not align properly with its blade; correct the assembly before use and replace damaged parts. Buy a replacement pitcher (Australia) or pitcher (New Zealand).

1. Switch off, unplug and wait for all movement to stop; detach the cup and easy-twist extractor blade from the motor base before unscrewing the blade from the cup.
2. Screw the blade securely onto the cup before fitting it to the base; keep the ingredients below MAX and wait until the motor has stopped before removing the assembly.

1. Clean the blade immediately after use by hand with soap and water; use a small brush or sponge for food around the blades, keeping fingers away from the sharp edges.
2. Dry the easy-twist extractor blade completely after every use before storing it.
3. For stubborn residue on an undamaged cup or blade, fill the cup to MAX with water at 21°C or cooler and add one or two drops of dish soap; attach the blade and blend for 20–30 seconds, then stop, unplug and scrub away the loosened food.
4. Rinse and brush food from the pitcher before dishwasher cleaning, or hand-wash it with soap and water; keep fingers away from its blades and never use the sanitise cycle.
5. For food stuck in an undamaged pitcher, fill it to MAX with water at 21°C or cooler and one or two drops of dish soap, attach its lid and blend for 20–30 seconds; stop and unplug before scrubbing.

1. Never leave the easy-twist extractor blade exposed on the motor base without a cup attached; store the appliance upright with nothing on top and keep loose parts where they cannot be damaged or cause injury.
2. Use liquid for blending; avoid running an empty cup or crushing ice and hard items without liquid, which can dull or damage the blade.
3. Store the pitcher upright with its lid fitted and nothing resting on the lid; keep the other parts in a safe place.

• Inspect the pitcher blades regularly; stop using the pitcher if the blades are damaged or no longer turn smoothly or freely.
• Check the pitcher for cracks, cloudiness or other damage and replace it if damaged; never use a pitcher that does not fit the motor base correctly.
• Also inspect the removable cup blade; if its blades are damaged or cannot rotate freely, discontinue use and arrange a matching replacement.

1. Turn off, unplug and wait until all moving parts stop, then remove the pitcher from the motor base before inspecting or washing it.

1. Rinse and scrub the pitcher with a dish brush before dishwasher cleaning, or hand-wash with soap and water; use a brush or sponge for stuck food without touching the sharp edges.
2. Avoid the sanitise cycle because high heat can warp the pitcher.
3. For residue in an undamaged cup or pitcher, fill to the liquid MAX line with 21°C water and one or two drops of dish soap; fit the cup blade or pitcher lid and vented cap, blend on LOW for 20–30 seconds, then stop and unplug before scrubbing.

1. Do not run an empty pitcher or crush ice alone; include sufficient liquid and avoid overloading so the blade can turn.
2. Turn off and unplug before adjusting ingredients, use a long spoon or silicone or wooden utensil rather than a sharp metal object, and remove it before restarting.
3. Store the pitcher upright with its lid on, no objects on top and the blade covered.
4. Do not grind dry grain, cereal or coffee; keep accessories off the bottom dishwasher rack and do not use a heat or sanitise cycle.

Ask for a blade assessment before choosing a replacement.

• Read the full product code from the appliance label and include NBF07200AKP in your enquiry.
• Include a clear photo of the blade and describe any wear, damage or change in performance you have noticed.

• Inspect the blade routinely; if it is bent or damaged, stop using the blender and arrange a replacement through our team.
• If a blockage stops an otherwise undamaged blade, add liquid and try again; shake or invert the blender to move the blockage, or turn it off before using a utensil to clear it.

1. During the warranty period, speak to our team before removing the blade so you receive the correct safety and replacement instructions.
2. Turn the blender off and unplug its charger before handling or cleaning the blade; wait until the blades stop before removing the cup or lid, and keep your fingers away from the edges.

1. Gently rinse the blade assembly and wipe it with a damp sponge or cloth. Do not put the motor base in a dishwasher or run the motor base under water.

1. Keep the cup fitted over the blade when storing the blender upright, and do not stack objects on top.
2. Remove stone-fruit pits before blending; hard ingredients can damage the blade.

• Routinely inspect the blade; stop using the blender if the blade is bent or damaged and arrange blade replacement through our team.
• Also stop if the Motor Base, Blade, and Lid assembly has been dropped or damaged; arrange assessment before further use.

1. Unplug the charger and leave the blender undisturbed for 90 seconds until it shuts down before cleaning or handling the blade; do not place fingers near its sharp edges when attaching the cup.

1. Point the blade downward at an angle, cover the USB-C port with a thumb or finger and carefully rinse only the blade area; use the supplied Cleaning Brush under the blades.
2. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the complete Motor Base, Blade, and Lid assembly or put it in the dishwasher; wipe and dry it with a clean cloth.
3. Dry the assembly upright with the Flip-Top Lid open and ensure the USB-C port is completely dry before charging.

1. Store the blade covered with the Cup or Blade Cover in a dry, temperature-controlled place; keep objects off the top of the blender.
2. Remove stone-fruit pits or seeds before blending; hard ingredients can damage the blade.

• Routinely inspect the blade; stop using the blender if the blade is bent or damaged and arrange blade replacement through our team.
• Also stop if the Motor Base, Blade, and Lid assembly has been dropped or damaged; arrange assessment before further use.

1. Unplug the charger and leave the blender undisturbed for 90 seconds until it shuts down before cleaning or handling the blade; do not place fingers near its sharp edges when attaching the cup.

1. Point the blade downward at an angle, cover the USB-C port with a thumb or finger and carefully rinse only the blade area; use the supplied Cleaning Brush under the blades.
2. NEVER submerge the entire Motor Base, Blade, and Lid in water. Do not rinse the complete Motor Base, Blade, and Lid assembly or put it in the dishwasher; wipe and dry it with a clean cloth.
3. Dry the assembly upright with the Flip-Top Lid open and ensure the USB-C port is completely dry before charging.

1. Store the blade covered with the Cup or Blade Cover in a dry, temperature-controlled place; keep objects off the top of the blender.
2. Remove stone-fruit pits or seeds before blending; hard ingredients can damage the blade.

These instructions describe the NBPB07222 Flex range. Include the full McLaren product code when requesting a blade for a McLaren pack.

• Routinely inspect the blade and stop using the Blade Block if its blade is bent or damaged; arrange a replacement through our team.

1. During the warranty period, speak to our team before removing the blade for safety instructions and replacement.
2. Turn off the blender and wait for the blade to stop; detach the Blade Block with a clockwise twist, holding it away from the cutting edges.

1. Hand-wash the Blade Block with warm, soapy water and rinse carefully, avoiding the sharp edges.
2. Wash the Cup and Sip Lid with Carry Loop by hand or on the top dishwasher rack without the heat or sanitise cycle.
3. Wipe the Motor Base with a damp cloth; never put it in the dishwasher or under water.

1. Attach the Blade Block to the Blending Cup before fitting it to the motor base; do not leave an exposed Blade Block on the base.
2. For storage, attach the cup and Sip Lid with Carry Loop to the Blade Block, stand the blender upright and place nothing on top.
3. Keep contents below MAX, use sufficient liquid with ice and remove non-food items before blending so the blade is not overloaded or damaged.

1. If the blade is obstructed, stop blending and add more liquid, or detach and gently shake or invert the Cup to shift the ingredients. For a persistent blockage, turn off and unplug the charger, twist off the Motor Base, place the vessel upside down on its closed Sip Lid, and carefully detach the Blade Block before clearing the obstruction. Never insert a hand or utensil inside the Cup to clear a blockage.

• Stop using the blender if it has malfunctioned or been dropped or damaged; obtain assistance before using it again.

1. Turn off the blender after use before cleaning; handle the blade assembly carefully without touching its sharp edges.

1. Gently rinse the blade assembly and wipe with a damp sponge or cloth; the blade assembly is not dishwasher-safe.
2. NEVER submerge the motor base in water. Do not run the motor base directly under water.

1. Keep the blender parts together in a safe storage place where the blade cannot cause harm or be damaged.
2. Do not blend ice or frozen ingredients; remove rinds, peels and stone-fruit pits before blending to protect the blade.

• For NBJ07100, replace the sieve every 12 months under high use, or as needed for best performance. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• Stop using the juicer if the sieve is damaged or its filter mesh is torn, crinkled or deformed; replace the damaged sieve. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• If the juicer becomes louder or develops unusual noise or vibration over time, stop and inspect the sieve and cleaning brush for wear; these consumable parts may need replacement. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).

1. Switch off, unplug and wait until the sieve and motor stop completely before opening the juicer.
2. Release the Locking Handle from the Basin Cover and lower it; lift the Pulp Basin, Basin Cover and Sieve together off the motor base and take them to the sink. Lift out the Food Pusher and Basin Cover, then gently lift the Sieve straight up from the centre of the Pulp Basin.

1. Use the supplied Cleaning Brush under running water to clean the sieve immediately after every use; avoid touching the sharp teeth on its flat disc.
2. If pulp has dried into the holes, soak the sieve in hot water for 30 minutes, then brush it clean; clear holes help restore juice extraction.
3. Hand-wash the sieve in warm soapy water or use the dishwasher without the Sterilize cycle; high heat can deform parts.

1. Remove stone-fruit pits and do not use frozen produce; use the supplied food pusher rather than fingers or utensils in the feed chute.

• For NBJ07150, replace the sieve every 12 months under high use, or as needed for best performance. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• Stop using the juicer if the sieve is damaged or its filter mesh is torn, crinkled or deformed; replace the damaged sieve. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• If the juicer becomes louder or develops unusual noise or vibration over time, stop and inspect the sieve and cleaning brush for wear; these consumable parts may need replacement. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).

1. Switch off, unplug and wait until the sieve and motor stop completely before opening the juicer.
2. Release the Locking Handle from the Basin Cover and lower it; lift the Pulp Basin, Basin Cover and Sieve together off the motor base and take them to the sink. Lift out the Food Pusher and Basin Cover, then gently lift the Sieve straight up from the centre of the Pulp Basin.

1. Use the supplied Cleaning Brush under running water to clean the sieve immediately after every use; avoid touching the sharp teeth on its flat disc.
2. If pulp has dried into the holes, soak the sieve in hot water for 30 minutes, then brush it clean; clear holes help restore juice extraction.
3. Hand-wash the sieve in warm soapy water or use the dishwasher without the Sterilize cycle; high heat can deform parts.

1. Remove stone-fruit pits and do not use frozen produce; use the supplied food pusher rather than fingers or utensils in the feed chute.

• If juice extraction drops, first remove residue from the Juicing Screen; blocked holes can reduce output even when the screen does not need replacing.
• If parts are difficult to separate, finish processing the remaining food for about 30 seconds without adding more produce, then stop and unplug before disassembly; adding water through the chute after juicing can help release residue.

1. Turn off, unplug, allow the juicer to cool and wait until all moving parts stop; close the juice spout, remove the juice and pulp containers, and twist the Juice Bowl Lid anticlockwise to lift it off.
2. Lift out the Auger, remove the Juice Bowl, then lift the Juicing Screen and Rotating Bowl Brush out together; slide the bowl brush downward off the screen.

1. Use the small Cleaning Brush to scrub the sharp Juicing Screen under running water after each use; do not touch its sharp surfaces or use a metal sponge.
2. Wash the screen in warm soapy water or the dishwasher; hand-wash the Auger with a soft cloth because it is not dishwasher-safe.

1. Remove hard pits, seeds and skin from produce and avoid thick, hard, low-juice foods; gently feed suitable ingredients with the Food Pusher.

• For high use, replace the sieve every 12 months or as needed for best performance. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• Stop using the juicer if the sieve is damaged or its filter mesh is torn, crinkled or deformed; replace the damaged sieve. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).
• If the juicer becomes louder or develops unusual noise or vibration over time, stop and inspect the sieve and cleaning brush for wear; these consumable parts may need replacement. Buy a replacement sieve/screen (Australia) or sieve/screen (New Zealand).

1. Switch off, unplug and wait until the sieve and motor stop completely before opening the juicer.
2. Release the locking handle, lift out the Food Pusher and Basin Cover, then gently lift the Sieve straight up from the centre of the Pulp Basin.

1. Use the supplied Cleaning Brush under running water to clean the sieve immediately after every use; avoid touching the sharp teeth on its flat disc.
2. If pulp has dried into the holes, soak the sieve in hot water for 30 minutes, then brush it clean; clear holes help restore juice extraction.
3. Hand-wash the sieve in warm soapy water or use the dishwasher without the Sterilize cycle; high heat can deform parts.

1. Remove stone-fruit pits and do not use frozen produce; use the supplied food pusher rather than fingers or utensils in the feed chute.

• Stop using the juicer if the strainer, sieve, Auger, Hopper or another removable part is damaged; replace the affected part before further use.

1. Turn the Dial to OFF, unplug and wait for the Auger and motor to stop; open the Lid, turn the Hopper anticlockwise until the arrows separate, then lift it off.
2. Pull the Auger straight up out of the Juicing Bowl, then lift the bowl off the motor base to inspect and clean the parts.
3. Refit the Juicing Bowl with its spouts aligned to the motor-base notches; push the Auger firmly into the centre until it reaches the bottom and locks.

1. After each use, empty and rinse the Hopper and Juicing Bowl, then scrub the Auger under running water with the Cleaning Brush; remove residue that can prevent proper operation.
2. Wash the detachable parts in warm soapy water or the dishwasher without the sterilise cycle; do not use metal sponges or abrasive pads.

1. Remove pits and large seeds, avoid frozen or low-juice foods, and feed without forcing the Food Pusher so the juicing parts do not jam.

• Regularly inspect the blades, whisk and attachments for damage or wear; they should rotate freely and have an undamaged structure, so stop using and replace damaged attachments. Buy a replacement whisk (Australia) or whisk (New Zealand).

1. Unplug, wait for movement to stop and detach the blending arm, whisk or chopping assembly before cleaning or changing attachments. NEVER submerge the main unit in water.

1. Clean the blade or whisk after every use so residue does not reduce blending performance; keep hands away from the sharp cutting edges.
2. Wash the chopping blade in warm soapy water or the dishwasher; wash the blending arm, whisk holder and chopping bowl lid by hand without soaking them or putting them in the dishwasher.
3. Avoid metal sponges; dry all parts thoroughly before storing them in a dry place.
4. If food dries onto dishwasher-safe detachable parts, soak them in hot water for 30 minutes to soften it; Keep the chopping bowl lid, blending arm and whisk holder out of that soak.

1. Check the blending vessel for cracks, crazing, cloudiness or other damage and replace a damaged vessel; do not assume a new blade will fix damaged plastic.

• Regularly inspect all blade attachments, discs and the adapter for damage or wear; stop using damaged parts, and check that blades can rotate freely and their structure is sound.

1. Switch off, unplug and wait for all movement to stop before removing the blades or other attachments from the motor base.

1. Clean the Blade Adaptor, Chopping Blade, Dough Blade, Slice/Shred Discs and Spiralizer Disc after every use by hand with warm soapy water or on the top dishwasher rack.
2. Avoid the sanitise cycle, steel wool and hard scouring materials that can warp or scratch the parts.

1. Keep non-food objects out, remove fruit rind, seeds and pits, and do not use the processor as an ice crusher because hard objects can damage the blades.
2. Use only attachments made for the NutriBullet Food Processor NBP07100.
3. For storage, fit the Blade Adaptor, then Chopping Blade and Dough Blade into the Work Bowl; lower the discs into the lower storage position without aligning their marks with the adaptor.
4. Store either two Slice/Shred Discs or one Slice/Shred Disc plus the Spiralizer Disc above the blades; if using the spiralizer, put it last and align FRONT to the front before locking the lid and seating the pusher.

• Before every use, inspect the Blade Block for damage and the Pint Cup for cracks; stop using parts that are or appear damaged and arrange replacement assistance.
• A CHECK BLADE light can mean the shaft is not fully retracted; check that the blade touches the top of the Blade Block before assuming a replacement is needed.

1. Unplug and wait until all parts stop moving before handling; hold the blade-holder assembly by its plastic grip, not the blade, shaft or blade cover.
2. The blade shaft may be hot after repeated use; if it feels warm, run it under cool water before handling.
3. If the stored Blade Block has engaged in the base, turn the blade anticlockwise to disengage it before lifting the block out.

1. Clean the Blade, Blade Block and Shaft after each use by hand with warm soapy water or on the top dishwasher rack; separate the Blade from the Blade Block before dishwasher cleaning.
2. For hand cleaning, use a sponge and dish soap around the Blade Block opening and Blade Shaft; avoid the sanitise cycle, steel wool and abrasive cleaners.

1. Store clean, dry parts with the Blade Cover fitted over the blade or with the blade attached to the Pint Cup; never leave the blade exposed on the motor base.
2. Remove utensils before processing and do not use hard ingredients, loose frozen fruit, ice or dry ingredients; process the prescribed frozen recipes rather than an empty cup or thawed liquid mixture.

• Inspect the Chopping Blade, Slice/Shred Disc, Blade Adaptor and other attachments for damage or wear; stop using damaged parts and arrange replacement.

1. Power off, unplug and wait until blades or discs stop; remove the tools before accessing the food, holding the top finger grip away from the cutting edge and never tipping a blade into your hand.

1. Clean the detachable blades, disc, adaptor, Endless Chute and Slinger Disc after every use in warm soapy water or on the top dishwasher rack; keep temperatures at or below 82°C and do not use the heat or sanitise cycle.
2. Do not use steel wool or other hard scouring materials, and avoid touching the cutting edges when washing by hand.

1. Do not crush ice or grind dry grains, cereal or coffee, and keep coffee beans, fruit pits, utensils and other hard items out of the processor.
2. Use only attachments made for the NutriBullet Limitless Food Processor NBP07300.
3. Store the Chopping Blade on the Blade Adaptor with the disc above it; lock the Work Bowl Lid and seat the Food Pusher, then store the Endless Chute and Slinger Disc separately.

• Inspect the extractor blade before every use and replace it every six months for best performance, or sooner if it becomes loose or damaged. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Check the gasket is fully seated before each use; if it is loose or damaged, replace the blade assembly. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Do not remove the blade seal; if it has been removed, stop using the blade immediately and buy a replacement.

1. Wash the blade by hand and keep it out of the dishwasher, as hot dishwasher water can damage the outer seal.

1. Unplug before changing attachments, wait for the motor to stop and keep fingers away from the sharp extractor blade.

1. Use only Baby attachments, never microwave the blade or other components, and remove the blade before covering blended food with the appropriate storage lid.

• Inspect the appliance before each use and stop using it if the Blending Blade is damaged; arrange a replacement blade before blending again.

1. Switch off, unplug, wait for the blade and motor to stop and let the appliance cool for at least 10 minutes before disassembly; let it cool completely before cleaning.
2. Remove the Blending Blade carefully by a non-sharp area; rotate the bottom of the Blade Holder to remove the holder from the Work Bowl.

1. Rinse the Blending Blade after each blending session so food residue cannot build up and reduce performance.
2. Hand-wash the Blending Blade and Blade Holder in warm soapy water and dry thoroughly; keep both out of the dishwasher.

1. Keep hard fruit and vegetables, citrus rind, pits, seed stones and non-food items out of the Work Bowl because they can damage the blade or motor.
2. Never place a cutting blade on the base without the bowl properly in place; fit the Work Bowl and its lid securely before operating.
3. Keep the appliance unplugged and its parts together in a dry, cool place for longer storage.

• Replace the Cross Blade every six months or as needed for best performance; inspect before each use and stop if it becomes loose or damaged. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Check the gasket is undamaged and fully seated before use; if it becomes loose or damaged, replace the whole Cross Blade. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Leave the gasket in place when cleaning; removing it can permanently damage the Cross Blade and cause leaking.

1. Unplug and wait for all movement to stop before removing the cup and blade from the motor base; hold the blade housing rather than its sharp edges.

1. Hand-wash the Cross Blade in warm soapy water, then rinse; if extra disinfecting is needed after washing, use a 10% vinegar-and-water solution.
2. Dry both sides completely by standing the blade on its side in a dish drainer.

1. Check all three cup tabs for cracking, crazing, breakage or rounding and replace a damaged cup; do not fit a new blade to a damaged cup.
2. Blend with liquid and do not crush ice or hard food without it, as continued use can dull or damage the blade.

• Replace the Cross Blade every six months or as needed for best performance; inspect before each use and stop if it becomes loose or damaged. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Check the gasket is undamaged and fully seated before use; if it becomes loose or damaged, replace the whole Cross Blade. Buy a replacement cross blade (Australia) or cross blade (New Zealand).
• Leave the gasket in place when cleaning; removing it can permanently damage the Cross Blade and cause leaking.

1. Unplug and wait for all movement to stop before removing the cup and blade from the motor base; hold the blade housing rather than its sharp edges.

1. Hand-wash the Cross Blade in warm soapy water, then rinse; if extra disinfecting is needed after washing, use a 10% vinegar-and-water solution.
2. Dry both sides completely by standing the blade on its side in a dish drainer.

1. Check all three cup tabs for cracking, crazing, breakage or rounding and replace a damaged cup; do not fit a new blade to a damaged cup.
2. Blend with liquid and do not crush ice or hard food without it, as continued use can dull or damage the blade.

• Replace the Cross Blade every six months, or as needed depending on use. Inspect it regularly and stop using it if it is damaged or does not rotate freely; arrange a replacement through our team.
• Check that the gasket is present and undamaged; replace a blade with a missing or damaged gasket rather than continuing to blend.
• Do not remove or replace the blade seal by itself; it is a non-removable part of the blade attachment.

1. Return the Power Control Knob to HOME, unplug and wait for the blade to stop.
2. For the Cup: twist it counter-clockwise to unlock it from the Motor Base, then turn it upright with the Cross Blade on top. Unscrew the Cross Blade before pouring out the contents.
3. For the Pitcher: twist it counter-clockwise and lift it off the Motor Base. Lift the lid tab to remove the lid, empty the contents, then unscrew the bottom Cross Blade in the direction shown on the Pitcher.
4. Keep your hands out of the Pitcher and away from the sharp edges when handling the Cross Blade.

1. Wash the Cross Blade by hand with soap and water or on the top dishwasher rack; never use the sanitise cycle.

1. Use only genuine parts designed for the Magic Bullet Blender Combo and store its components together with the blades covered.

• Inspect the sieve before every use and replace it if it is cracked, bent or damaged; do not keep using a damaged sieve or a visibly cracked protective cover.
• Replace the sieve when it looks dull or works less efficiently; clean away residue first so blocked holes are not mistaken for wear.

1. Switch off, unplug and wait for the sieve and motor to stop; release both locking arms and remove the cover before gently lifting the sieve out of the juice bowl.

1. Brush the sieve under running water immediately after juicing, using the supplied Cleaning Brush rather than your fingers; brush the outside first, then the inside.
2. If dried pulp blocks the holes, soak the sieve in hot water for 30 minutes before brushing it clean.
3. Hand-wash the sieve with warm soapy water or put it in the dishwasher; never use the heat sanitation cycle.

1. Remove pits and seed stones from produce, do not juice frozen fruit or vegetables, and feed gradually without excessive force on the Food Pusher.

• Stop using the appliance if any part is damaged; inspect the Cross Blade, Chopping Blade and disc rather than continuing with a damaged attachment.

1. Turn the control knob to OFF, unplug and wait until all moving parts stop.
2. For the Work Bowl: turn it counter-clockwise to unlock it from the Motor Base and place it on a clean, dry, flat surface. Turn the lid counter-clockwise to remove it.
3. Carefully lift the Chopping Blade off the bowl shaft, keeping your fingers away from the sharp edges. If using the slicing/shredding disc, lift it by its two large finger holes. Remove the cutting attachment before pouring food out of the Work Bowl.
4. For the Cup: turn the sealed Cup counter-clockwise to unlock it from the Motor Base, then turn it upright with the Cross Blade on top. Unscrew the Cross Blade before pouring out the contents.

1. Wash the Cross Blade, Chopping Blade and disc by hand with warm soapy water or on the top dishwasher rack, then rinse; do not use the sanitise cycle.

1. Store all parts together in a safe place where the cutting tools cannot cause harm or be damaged.

• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement. Buy a replacement extractor blade (Australia) or extractor blade (New Zealand).
• Inspect the processor Chopping Blade, Slice/Shred Disc and grinder blade for damage or wear as well as the Rapid Extractor Blade; do not operate with damaged attachments.

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.
3. For the processor, wait for the blade or disc to stop, unplug, turn the Work Bowl Lid anticlockwise and lift it off, then remove the Work Bowl and Processor Base; lift the blade or disc by its central plastic knob, never by tipping it into your hand.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.
4. Wash processor blades and discs by hand with soap and water or on the top dishwasher rack; hand-wash the Processor Base and Blade Adapter and never use the heat or sanitise cycle.
5. Soak stubborn food on processor blades or discs in room-temperature water with one or two drops of dish soap for 20–30 seconds, then scrub away the loosened residue.
6. Separate the grinder blade from the Grinding Cup after unplugging; wash both by hand or on the top dishwasher rack without the heat or sanitise cycle, then keep the grinder in a clean, cool, dry place.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.
6. Store the Chopping Blade and Slice/Shred Disc inside the Work Bowl; put the disc in its lower storage position without aligning its marks with the Blade Adapter, then attach the lid.
7. Never use the grinder attachment as a storage container or leave an exposed grinder blade on the base.

• Replace the extractor blade every six months, depending on use, or sooner when needed for best performance.
• Before each use, check that the gasket sits completely in the blade housing; replace the whole blade assembly if the seal is damaged.
• If the gasket becomes loose, stop using the blade and obtain a complete replacement; do not pull the gasket out or fit a separate seal.

1. Unplug the motor base, wait until every moving part has stopped, then remove the cup and extractor blade assembly from the base before separating the parts.
2. Securely screw the blade base onto the cup before placing the assembly on the motor base; the blade should sit securely without leaking.

1. Hand-wash the extractor blade with warm soapy water and rinse; keep the sharp edges away from your fingers and leave the gasket fitted.
2. For extra disinfecting after washing, rinse the blade with a 10% vinegar-and-water solution or lemon juice.
3. Stand the blade on its side in a dish drainer and let both sides dry completely before putting it away.
4. For dried food in an undamaged cup and blade, fill the cup about two-thirds full with water at 21°C or cooler, screw on the blade and blend for 20–30 seconds; stop, unplug, then lightly scrub and rinse away the loosened residue.

1. Add liquid before blending and never run the extractor blade in an empty cup; do not use it as an ice crusher.
2. Wait for the motor to stop before taking the cup and blade off the base so the blade coupling and motor gear are not damaged.
3. Check all three cup tabs for cracks, crazing, breakage or rounding; replace a damaged cup instead of trying to solve a cup fault by fitting a new blade.
4. Never store an exposed extractor blade on the motor base; attach its cup or store the detached blade where its cutting edges cannot cause injury.

• Replace the Rapid Extractor Blade every 12–18 months, depending on use, or at the first signs of wear and tear.
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement.

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.

• Replace the Rapid Extractor Blade every 12–18 months, depending on use, or at the first signs of wear and tear.
• Periodically inspect the blades and stop using the Rapid Extractor Blade if they are damaged or cannot rotate freely.
• Check the gasket is present and undamaged; stop using the Rapid Extractor Blade if the gasket is missing or damaged and arrange a replacement.

1. Switch off and unplug the motor base, wait for the blades to stop, then remove the cup and blade assembly; never pull the cup away while the blade is moving.
2. Securely tighten the Rapid Extractor Blade onto the cup before use; if leaking starts, stop blending and wait for the motor to stop before removing the assembly.

1. Rinse the Rapid Extractor Blade with warm soapy water and use a small brush or sponge to remove residue; clean it immediately after use so food does not dry on it.
2. For stubborn food on an undamaged cup or blade, fill the cup to MAX with room-temperature water and one or two drops of dish soap, attach the blade and blend for 20–30 seconds; stop and unplug before scrubbing away the loosened food.
3. Keep the blade off the bottom dishwasher rack and never use a heat or sanitise cycle; do not boil the blade or put it in an oven, microwave, air fryer or stovetop pot.

1. Do not grind dry grain, cereal or coffee with the Rapid Extractor Blade, crush ice alone, or operate with an empty cup; add sufficient liquid and remove stone-fruit pits before blending.
2. Keep ingredients below MAX; if an overload stops the blades, turn off the blender, reduce the contents to MAX, refit the cup, and resume only with undamaged parts.
3. Check the cup for cracks, cloudiness, warping or other damage and replace a damaged cup; a replacement blade does not repair a damaged vessel.
4. Do not use the Rapid Extractor Blade as a storage lid; use the To-Go Lid or transfer the blend to a vented container.
5. Keep the blade covered by its cup during storage and never leave an exposed blade on the motor base; store the blender upright with nothing on top.