NutriBullet Immersion Blender 800W

Wash the detachable parts, lock the chosen attachment, prepare the food, then hold Low-speed (I) to run your NutriBullet Immersion Blender 800W and release it to stop.

1. Before first use, wash and dry the detachable parts with warm soapy water, keeping the motor body and chopping-bowl lid out of the wash.
2. With the motor unplugged, fit the attachment: push the motor body into the blending arm or assembled whisk holder and turn clockwise, or seat the chopper S-blade on its centre pin by holding the upper plastic part. NEVER submerge the main unit in water.
3. Add prepared food without exceeding MAX, leave at least 100mm of space at the top, and include liquid for blending or whisking.
4. For the chopper, turn its lid clockwise to lock, then push the motor body into the lid and turn clockwise until secured.
5. For the arm or whisk, hold the attachment upright in the mixture before connecting power or pressing a button.
6. Plug in and hold Low-speed (I) to start, keeping one hand on the motor body and one on the bowl when chopping.
7. Release the button to stop, wait until all movement stops before lifting the attachment, and unplug before detaching it.
8. Keep ordinary blends generally under one minute, whisk for no longer than two minutes, chop hard permitted foods for no longer than five seconds, and allow at least five minutes between uses.

See cleaning, ingredient safety and storage.

NutriBullet Immersion Blender 800W: model number NBI-100; product code (SKU) NBI07110.

NutriBullet EveryGrain Cooker

Wash the removable parts, measure grains and water into the Cooking Pot, seat the pot and close the lid, then choose a program and press Start/Stop on your NutriBullet EveryGrain Cooker.

1. Before first use, hand-wash the Cooking Pot and wash the Steaming Basket, Spatula and Measuring Scoop with warm soapy water.
2. Add grains first, then water using the supplied scoop and the matching pot markings, keeping everything below the highest pot line.
3. Keep within the grain limit: up to five scoops of rice or other grains, four of quinoa or oats, and no more than two of farro or barley.
4. Seat the clean Cooking Pot level on the heating plate inside the base, placing the base on a clean, dry, level surface. NEVER submerge the main unit in water.
5. If steaming, sit the food-filled Steaming Basket level inside the pot, using one supplied scoop of water in the pot when steaming without grains.

Next steps

1. Push the lid down until it clicks, connect the cord to the base and outlet, and press Power.
2. Select a grain program or Steam and press Start/Stop, setting the Steam time with the arrows first if using that program.
3. Press Start/Stop to stop or allow the program to finish, then use oven mitts for the hot pot or basket and unplug before removing parts after they have cooled.
4. Steam can be set for up to one hour, and the cooker automatically keeps food warm for up to three hours after cooking.

See cleaning, ingredient safety and storage.

NutriBullet EveryGrain Cooker: model number NGC-100; product code (SKU) NBG07100.

NutriBullet Food Processor

Wash the detachable parts, fit one blade or disc and prepare the food, lock the lid and bowl, then select LOW, HIGH or PULSE on your NutriBullet Food Processor.

1. Before first use, wash the detachable parts with warm soapy water, handling blades by their plastic centres.
2. With the base unplugged, press the Blade Adaptor onto the Work Bowl shaft and fit one cutting attachment.
3. Seat the chosen blade or disc correctly: push a chopping or dough blade to the bottom, align the Slice/Shred Disc markings in its higher operating position with the required side up, or align the Spiralizer Disc notches and turn FRONT towards the base front.
4. For chopping or dough, add prepared ingredients after fitting the blade without passing LIQUID MAX, or keep disc-processing food aside until the motor runs.
5. Turn the lid clockwise until its arrows align with the handle, insert the Food Pusher, and turn the lidded bowl clockwise onto the base until it clicks.

Next steps

1. Plug in and select LOW or HIGH for continuous processing or hold PULSE for a burst, using LOW for dough and HIGH for discs.
2. For a disc, feed the prepared pieces only after starting the motor, guiding them gently with the supplied Food Pusher.
3. Press OFF or release PULSE, wait for the blade to stop, unplug, and turn the bowl and lid counterclockwise to unlock before removing the blade by its plastic centre.
4. Run for no longer than one minute and wait at least one minute before another processing cycle.

See cleaning, ingredient safety and storage.

The Food Processor motor will not run unless the lid is locked into place.

The Food Processor motor will not run unless the lid is locked into place.

NutriBullet Food Processor: model number NBP-100; product code (SKU) NBP07100.

NutriBullet Chill

Wash the removable parts, freeze a prepared recipe in the Pint Cup, fit and lock the blade-and-cup assembly, then choose a dessert program and press Start/Stop on your NutriBullet Chill.

1. Before first use, wash the removable parts with warm soapy water and inspect the Pint Cup and Blade Block for damage.
2. Fill the Pint Cup between MIN FILL and MAX FILL with a prepared dessert recipe, snap on the lid and freeze level for at least 24 hours.
3. Remove the frozen cup and its lid and process within five minutes, keeping the Blade Shaft completely dry inside and out.
4. With power disconnected, fully retract the Blade Shaft until the blade touches the top of the Blade Block, then screw the Blade Block clockwise onto the cup.
5. Lower the inverted cup onto the base shaft-first, align its tabs with the notches, then press down and turn clockwise to lock.

Next steps

1. Connect power, select the dessert program and press Start/Stop, allowing the program to run through its normal pauses until it beeps.
2. To finish early, hold Start/Stop for two seconds to cancel, and wait for the blade to stop before holding Cup Release and turning the cup counterclockwise to remove it.
3. Unplug before removing the Blade Block, turning it counterclockwise and handling it by its plastic grip.
4. Programs take approximately three to four and a half minutes. The full steps for this model are in its user guide.

See cleaning, ingredient safety and storage.

NutriBullet Chill: model number NBD-100; product code (SKU) NBD07100AW, NBD07100CCP, NBD07100MCG.

NutriBullet Limitless Food Processor

Wash the detachable parts, fit one cutting attachment, load and lock the Work Bowl or Endless Chute, then slide the handle toggle to ON or hold PULSE on your NutriBullet Limitless Food Processor.

1. Before first use, wash the detachable parts with warm soapy water, holding sharp attachments by their plastic areas.
2. With power disconnected, fit the chosen attachment: seat the Chopping Blade on the Work Bowl adaptor, or fit the Slice/Shred Disc with the required side facing up.
3. For the Endless Chute instead, lock it clockwise onto the base, press the Slinger Disc into its bottom opening, fit the Slice/Shred Disc onto its stem and place a receiving bowl under the outlet.
4. For chopping, load prepared ingredients after fitting the blade and keep liquid at or below LIQUID MAX, or keep slicing and shredding food aside until the motor runs.
5. Lock the lid clockwise with its markings aligned to the handle, insert the Food Pusher, and lock the Work Bowl clockwise onto the base until it clicks if using that bowl.
6. Plug in and slide the toggle to ON or hold PULSE, feeding disc-processing food gently with the supplied Food Pusher after the motor starts.
7. Slide to OFF or release PULSE, wait until the blade or disc stops and unplug before unlocking the bowl and lid or handling the cutting attachment by its plastic grip.
8. The Endless Chute stops after 120 seconds; the guide gives food-specific processing times but no general maximum Work Bowl run time or timed cooling interval.

See cleaning, ingredient safety and storage.

NutriBullet Limitless Food Processor: model number NBP-300; product code (SKU) NBP07300.

NutriBullet Baby

Wash the parts, load and seal the Short Cup or assemble and fill the Batchbowl, then push down and twist clockwise to start your NutriBullet Baby and turn counterclockwise to stop.

1. Before first use, wash the cup or Batchbowl with warm soapy water and hand-wash the Extractor Blade without removing its seal.
2. For the Short Cup, add liquid and completely cooled, prepared food below MAX, then twist the Extractor Blade on until tightly sealed.
3. For the Batchbowl instead, twist the Extractor Blade onto the empty bowl first, add prepared food and liquid below MAX, then firmly fit its lid and cap.
4. Connect power and place the assembled vessel onto the base, then push down and twist clockwise to blend.
5. Turn counterclockwise to stop, wait until all moving parts have stopped before lifting the vessel off, and unplug before removing the blade.
6. Do not blend continuously for more than one minute.

See cleaning, ingredient safety and storage.

NutriBullet Baby: model number BB-101K; product code (SKU) NBY-1807.

NutriBullet Baby Steam + Blend

Wash the parts and run the initial cleaning cycle, load prepared food and water, lock the lid and bowl, then select a setting and press Power on your NutriBullet Baby Steam + Blend.

1. Before first use, wash and dry the blade, holder, Work Bowl and lid with warm soapy water, handling the blade by a non-sharp area.
2. With the base unplugged, lower the blade onto the bowl holder, turn the lid clockwise to lock, align the bowl arrow with Unlock and turn the bowl counterclockwise onto the base.
3. For the initial cleaning cycle, fill the reservoir to the 25-minute line, lock its cap clockwise, plug in, select Steam and press Power.
4. When that cycle finishes, unplug and let everything cool completely, then lift the blade vertically with a mitt and discard remaining water from the bowl and reservoir.
5. For a food batch, fill the cold reservoir to the food’s steaming-time marking and refit its cap before fitting the blade and loading prepared food below MAX and below the pour-spout vents.

Next steps

1. Lock the lid clockwise and bowl counterclockwise onto the base, then plug in and check for one beep and a steady blue light.
2. Select Steam, Blend or Steam + Blend and press Power, allowing the combined setting to steam and then blend automatically.
3. Press Power to stop early or wait for completion, then unplug and wait at least ten minutes and until the unit is fully cool and every moving part has stopped.
4. Turn the bowl clockwise to unlock, open the lid, lift the blade vertically with a mitt and remove the food with a non-metal spoon or spatula.
5. The standard Blend cycle runs for one minute, and food must be fully cooked and at a safe serving temperature before feeding.

See cleaning, ingredient safety and storage.

NutriBullet Baby Steam + Blend: model number NBY-200; product code (SKU) NBY07200.