Skip to main content

How can we help?

How do I assemble and start using my personal blender?

  • Updated

Wash the parts, fill the cup to MAX or below, seal it with its blade, fit it to the base and use the start and stop controls for your model.

If you need help with an unresolved issue, take your claim, with your receipt, to the place of purchase (the manufacturer warranty is 12 months from the date of purchase).

NutriBullet 700 Series

For NutriBullet 700 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Blend for no more than 45 seconds per interval or three consecutive intervals; between intervals, let the motor stop completely and the cup cool, carefully open it to release pressure and wait at least one minute before resealing and restarting.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Ultra 1200

For NutriBullet Ultra 1200, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
  5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
  6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 900 Series

For NutriBullet 900 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 900 Essentials Set (AU and NZ)

For NutriBullet 900 Essentials Set NB9-0807DG (AU and NZ), wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 900 Mega Pack (AU and NZ)

For NutriBullet 900 Mega Pack NB9-1107AK (AU and NZ), wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 600 Series

For NutriBullet 600 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Ultra 1000 / Ultra 1000 Premium

For NutriBullet Ultra 1000 Premium NB07500-1008, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
  5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
  6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Select 1200 / 2.0 Select 1200

For NutriBullet Select 1200 / 2.0 Select 1200, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup onto the powered base and select LOW, HIGH or EXTRACT, then stop the motor before unlocking and removing the cup.

  1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, press POWER, lock the inverted cup clockwise onto the base and press LOW, HIGH or EXTRACT to blend.
  5. Press POWER or the selected speed/program button to stop, wait until the blades have completely stopped, power off, then twist the cup anticlockwise, lift it off and unplug the base.
  6. Speeds shut off automatically after 60 seconds; do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Pro+ 1200 / Pro Plus 1200

For NutriBullet Pro+ 1200 / Pro Plus 1200, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Untwist the cup anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic blend stops after 60 seconds; do not exceed one minute per interval or three intervals without allowing the motor to cool for 2–3 minutes after the third.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Pro 1000 / 2.0 Pro 1000

For NutriBullet 2.0 Pro 1000 NB07100-1008DG, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
  5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic extraction cycle lasts one minute; do not blend continuously for longer than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 1000 Series

Fill the cup below MAX, twist the extractor blade on tightly, plug in, then turn the cup upside down onto the motor base and gently push and twist.

How do I put it together?
  • Place the motor base on a clean, dry, level surface, such as a bench or table.
  • Add ingredients and liquid to the cup. Do not fill past the MAX line.
  • Place the extractor blade on the cup and twist until it is tightly sealed. Plug the power cord into a power point.
  • Turn the cup upside down onto the motor base, then gently push down and twist.
How do I take the cup off?
  • Wait until the motor has completely stopped before removing the cup.
  • Gently push and untwist the cup anticlockwise to unlock it. Do not remove the extractor blade from the cup until blending has completely stopped.
How long can I blend?
  • Do not blend continuously for more than one minute.
  • Before another cycle, let the contents settle for 2–3 minutes. Check the cup is not hot or warm, carefully open it to release pressure, then tighten it again.
What can I put in it?
  • Use room-temperature or refrigerated ingredients and liquids, 21°C or cooler. Never put hot liquids in the cup.
  • Always add liquid and never run it empty. Never blend carbonated (fizzy) ingredients or liquids.

NutriBullet Turbo 1000

For NutriBullet Turbo 1000, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
  5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 1000 Mega Pack / 1000 Series Mega Pack

For NutriBullet 1000 Mega Pack N10-1107AK, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute; before another cycle, let the contents settle for 2–3 minutes, check the cup is cool, carefully open it to release pressure and securely refit the blade.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 1200 Series / 12 Piece

Add cool ingredients and liquid below the MAX line, screw the extractor blade tightly onto the cup, then place the cup on the power base set on a level surface.

How do I check the parts first?
  • Make sure the power base is unplugged before assembling, taking apart, adding parts or cleaning.
  • Check the gasket is completely seated in the blade before each use. If the seal is damaged, replace the complete blade assembly.
  • Check the 3 tabs on the side of the cup. Never use a cup with a broken, damaged or missing tab.
  • Inspect the blades before each use. Blades are sharp, so handle them carefully.
How do I fill and assemble the cup?
  • Start with cool or room-temperature ingredients. Never put hot liquids or carbonated ingredients in the cup.
  • Always add liquid and keep all ingredients below the MAX line. Overfilling can cause leaks and dangerous pressure.
  • Remove any spoon or other object from the cup before blending.
  • Screw the extractor blade securely onto the cup before placing it on the power base.
Where should I set up the power base?
  • Use it on a level surface with clear space beneath and around the power base so air can circulate.
  • Do not let the cord hang over the edge of the bench or touch hot surfaces, including the stove.
What should I do while and after blending?
  • Do not run the motor continuously for more than one minute. Never leave the blender unattended while it is in use.
  • Wait until the motor comes to a complete stop before removing the cup and blade from the power base.
  • If the cup is warm to touch, let it cool before carefully opening it pointed away from your body.
  • Never store the extractor blade on the power base without a cup attached. Unplug the blender when it is not in use.

NutriBullet 1200 Series / 10 Piece

Add cool ingredients and liquid below the MAX line, screw the extractor blade tightly onto the cup, then place the cup on the power base set on a level surface.

How do I check the parts first?
  • Make sure the power base is unplugged before assembling, taking apart, adding parts or cleaning.
  • Check the gasket is completely seated in the blade before each use. If the seal is damaged, replace the complete blade assembly.
  • Check the 3 tabs on the side of the cup. Never use a cup with a broken, damaged or missing tab.
  • Inspect the blades before each use. Blades are sharp, so handle them carefully.
How do I fill and assemble the cup?
  • Start with cool or room-temperature ingredients. Never put hot liquids or carbonated ingredients in the cup.
  • Always add liquid and keep all ingredients below the MAX line. Overfilling can cause leaks and dangerous pressure.
  • Remove any spoon or other object from the cup before blending.
  • Screw the extractor blade securely onto the cup before placing it on the power base.
Where should I set up the power base?
  • Use it on a level surface with clear space beneath and around the power base so air can circulate.
  • Do not let the cord hang over the edge of the bench or touch hot surfaces, including the stove.
What should I do while and after blending?
  • Do not run the motor continuously for more than one minute. Never leave the blender unattended while it is in use.
  • Wait until the motor comes to a complete stop before removing the cup and blade from the power base.
  • If the cup is warm to touch, let it cool before carefully opening it pointed away from your body.
  • Never store the extractor blade on the power base without a cup attached. Unplug the blender when it is not in use.

NutriBullet 2.0 Pro 1200

For NutriBullet 2.0 Pro 1200, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
  5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic extraction cycle lasts one minute; do not blend continuously for longer than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 500 Series / 4 Piece

For NutriBullet 500 Series / 4 Piece, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 1000 Essentials McLaren

For NutriBullet 1000 Essentials McLaren, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute; before another cycle, let the contents settle for 2–3 minutes, check the cup is cool, carefully open it to release pressure and securely refit the blade.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Select 1000 / Select 1000 with pitcher

For NutriBullet Select 1000 NB07200-1007DG with its blending cup, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup onto the powered base and select LOW, HIGH or EXTRACT, then stop the motor before unlocking and removing the cup.

  1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, press POWER, lock the inverted cup clockwise onto the base and press LOW, HIGH or EXTRACT to blend.
  5. Press POWER or the selected speed/program button to stop, wait until the blades have completely stopped, power off, then twist the cup anticlockwise, lift it off and unplug the base.
  6. Speeds shut off automatically after 60 seconds; do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Pro+ Matte Black

Add cool ingredients and liquid to the cup below the MAX line, screw the extractor blade on securely, then place the cup on the power base. Never run it for more than one minute at a time.

How do I put it together?
  • Make sure the power base is unplugged while you assemble it.
  • Place it on a level surface with clear space under and around the power base for airflow.
  • Add ingredients and liquid to the cup. Do not go past the MAX line.
  • Check the gasket is fully seated in the blade before each use.
  • Screw the blade base securely onto the cup before placing it on the power base.
What can I put in it?
  • Start with cool or room-temperature ingredients. Do not put hot liquids in the cup.
  • Never blend carbonated (fizzy) ingredients or liquids.
  • Always add liquid and never run it with an empty cup.
  • Do not use apple seeds, apricot seeds, cherry pips, plum pips or peach pips.
How long can I blend, and when can I take the cup off?
  • Do not run it continuously for more than one minute.
  • Wait until the motor has completely stopped before removing the cup and blade from the power base.
  • If the cup is warm to touch, let it cool, then open it carefully, pointed away from your body.

NutriBullet 600 Essentials Kit

For NutriBullet 600 Essentials Kit with its extractor-blade cup, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Ultra 1200 McLaren / Club Pack

For NutriBullet Ultra 1200 McLaren NB07500-1206GO-MC, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
  5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
  6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Ultra 1200 Premium

For NutriBullet Ultra 1200 Premium, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
  5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
  6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Ultra Plus+ Compact Kitchen System

For NutriBullet Ultra Plus+ Compact Kitchen System with its blending cup, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
  5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
  6. The automatic blend stops after 30 seconds; do not exceed one minute of continuous blending or six consecutive 30-second intervals.
  7. Between repeat cycles, carefully open the cooled cup to release pressure before resealing it, and allow the contents to settle for 10–15 minutes after the last cycle.
  8. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet 600 Mega Pack

For NutriBullet 600 Mega Pack with its extractor-blade cup, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the extractor blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
  5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. Do not blend continuously for more than one minute.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Turbo 1000 Deluxe Set

For NutriBullet Turbo 1000 Deluxe Set, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
  5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

NutriBullet Turbo Ultimate Pack

For NutriBullet Turbo Ultimate Pack, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

  1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
  2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
  3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
  4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
  5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
  6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
  7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

What if the blender will not start?

Follow the personal blender start and stop checks for your selected model.

What if the cup leaks?

Follow the personal blender leak checks for your selected model.

Still need help? Chat with us and give us your model name and product code.

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Essentials Set NB9-0807DG user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 900 Mega Pack NB9-1107AK user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: NutriBullet 1000 Essentials McLaren user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

The full steps for this model are in its user guide: Read the user guide (PDF)

Related articles

Contact us