NutriBullet Ultra 1200

For NutriBullet Ultra 1200, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Ultra 1200: model number NB-500; product code (SKU) NB07500-1206DG.

NutriBullet 900 Series

For NutriBullet 900 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 900 Series: model number NB-201, NB-201S; product code (SKU) NB9-0507, NB9-0507AB, NB9-0507ABG, NB9-0507AFG, NB9-0507AK, NB9-0507ALP, NB9-0507ALW, NB9-0507AMG, NB9-0507ANB, NB9-0507ASP, NB9-0507AW, NB9-0507AY, NB9-0507MAC, NB9-0507MAJ, NB9-0507MAK, NB9-0507MAS, NB9-0507MASL, NB9-0507MB, NB9-0507MF, NB9-0507MM, NB9-0507MT, NB9-0507W, NB9-0507YE.

NutriBullet 900 Essentials Set (AU and NZ)

For NutriBullet 900 Essentials Set NB9-0807DG (AU and NZ), wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 900 Essentials Set (AU and NZ): model number NB-201, NB-201S; product code (SKU) NB9-0807DG.

NutriBullet 900 Mega Pack (AU and NZ)

For NutriBullet 900 Mega Pack NB9-1107AK (AU and NZ), wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 900 Mega Pack (AU and NZ): model number NB-201, NB-201S; product code (SKU) NB9-1107AK, NB9-1107EUC, NB9-1107LAV, NB9-1107LIN, NB9-1107MASL, NB9-1107MM, NB9-1107SHE.

NutriBullet 600 Series

For NutriBullet 600 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 600 Series: model number NB-101, NB-101B, NB-101S; product code (SKU) NBR-0507ALP, NBR-0507AMG, NBR-0507ANB, NBR-0507ASP, NBR-0507AW, NBR-0507AY, NBR-0507GK, NBR-0507GNB, NBR-0507GP, NBR-0507GSB, NBR-0507GW, NBR-0507IND, NBR-0507LAG, NBR-0507LG, NBR-0507LIN, NBR-0507MAC, NBR-0507MAJ, NBR-0507MAK, NBR-0507MAS, NBR-0507MASL, NBR-0507MB, NBR-0507MF, NBR-0507MM, NBR-0507MT, NBR-0507PAR, NBR-0507PB, NBR-0507PLG, NBR-0507PP, NBR-0507SHE.

NutriBullet Ultra 1000 / Ultra 1000 Premium

For NutriBullet Ultra 1000 Premium NB07500-1008, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Ultra 1000 / Ultra 1000 Premium: model number NB-500A; product code (SKU) NB07500-1004AK, NB07500-1004AW, NB07500-1004BR, NB07500-1004SS, NB07500-1006, NB07500-1008.

NutriBullet Select 1200 / 2.0 Select 1200

For NutriBullet Select 1200 / 2.0 Select 1200, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup onto the powered base and select LOW, HIGH or EXTRACT, then stop the motor before unlocking and removing the cup.

1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, press POWER, lock the inverted cup clockwise onto the base and press LOW, HIGH or EXTRACT to blend.
5. Press POWER or the selected speed/program button to stop, wait until the blades have completely stopped, power off, then twist the cup anticlockwise, lift it off and unplug the base.
6. Speeds shut off automatically after 60 seconds; do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Select 1200 / 2.0 Select 1200: model number NB2-S12; product code (SKU) NB07200-1210DG.

NutriBullet Pro+ 1200 / Pro Plus 1200

For NutriBullet Pro+ 1200 / Pro Plus 1200, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Untwist the cup anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic blend stops after 60 seconds; do not exceed one minute per interval or three intervals without allowing the motor to cool for 2–3 minutes after the third.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Pro+ 1200 / Pro Plus 1200: product code (SKU) N12-1007MK.

NutriBullet Pro 1000 / 2.0 Pro 1000

For NutriBullet 2.0 Pro 1000 NB07100-1008DG, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic extraction cycle lasts one minute; do not blend continuously for longer than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Pro 1000 / 2.0 Pro 1000: model number NB2-10; product code (SKU) NB07100-1007DG, NB07100-1008DG.

NutriBullet 1000 Series

Fill the cup below MAX, twist the extractor blade on tightly, plug in, then turn the cup upside down onto the motor base and gently push and twist.

NutriBullet 1000 Series: model number NB-202; product code (SKU) N10-0807DG.

NutriBullet Turbo 1000

For NutriBullet Turbo 1000, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Turbo 1000: model number NB-400; product code (SKU) NBT07400-1004AW, NBT07400-1006AK, NBT07400-1006AW.

NutriBullet 1000 Mega Pack / 1000 Series Mega Pack

For NutriBullet 1000 Mega Pack N10-1107AK, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute; before another cycle, let the contents settle for 2–3 minutes, check the cup is cool, carefully open it to release pressure and securely refit the blade.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 1000 Mega Pack / 1000 Series Mega Pack: product code (SKU) N10-1107AK, N10-1107EUC, N10-1107LIN, N10-1107MB, N10-1107MM, NB10-1107AK.

NutriBullet 1200 Series / 12 Piece

Add cool ingredients and liquid below the MAX line, screw the extractor blade tightly onto the cup, then place the cup on the power base set on a level surface.

NutriBullet 1200 Series / 12 Piece: model number NB-203; product code (SKU) N12-1207C.

NutriBullet 1200 Series / 10 Piece

Add cool ingredients and liquid below the MAX line, screw the extractor blade tightly onto the cup, then place the cup on the power base set on a level surface.

NutriBullet 1200 Series / 10 Piece: product code (SKU) N12-1007.

NutriBullet 2.0 Pro 1200

For NutriBullet 2.0 Pro 1200, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic extraction cycle lasts one minute; do not blend continuously for longer than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 2.0 Pro 1200: model number NB2-12; product code (SKU) NB07100-1208DG.

NutriBullet 500 Series / 4 Piece

For NutriBullet 500 Series / 4 Piece, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 500 Series / 4 Piece: model number NB-100; product code (SKU) NB5-0407DG, NB5-0407MAW.

NutriBullet 1000 Essentials McLaren

For NutriBullet 1000 Essentials McLaren, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute; before another cycle, let the contents settle for 2–3 minutes, check the cup is cool, carefully open it to release pressure and securely refit the blade.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 1000 Essentials McLaren: product code (SKU) N10-0807GO-MC, NB10-0807GO-MC.

NutriBullet 700 Series

For NutriBullet 700 Series, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Blend for no more than 45 seconds per interval or three consecutive intervals; between intervals, let the motor stop completely and the cup cool, carefully open it to release pressure and wait at least one minute before resealing and restarting.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 700 Series: model number NB-150; product code (SKU) NB07150-0704, NB07150-0704BPK, NB07150-0704LIN, NB07150-0704MNG, NB07150-0704TB.

NutriBullet Select 1000 / Select 1000 with pitcher

For NutriBullet Select 1000 NB07200-1007DG with its blending cup, wash the parts, fill the cup below MAX, twist on the easy-twist extractor blade, lock the inverted cup onto the powered base and select LOW, HIGH or EXTRACT, then stop the motor before unlocking and removing the cup.

1. With the base unplugged, hand-wash the cup, lid and easy-twist extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the easy-twist extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, press POWER, lock the inverted cup clockwise onto the base and press LOW, HIGH or EXTRACT to blend.
5. Press POWER or the selected speed/program button to stop, wait until the blades have completely stopped, power off, then twist the cup anticlockwise, lift it off and unplug the base.
6. Speeds shut off automatically after 60 seconds; do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Select 1000 / Select 1000 with pitcher: product code (SKU) NB07200-1006DG, NB07200-1007DG.

NutriBullet Pro+ Matte Black

Add cool ingredients and liquid to the cup below the MAX line, screw the extractor blade on securely, then place the cup on the power base. Never run it for more than one minute at a time.

NutriBullet Pro+ Matte Black: product code (SKU) N12-1207MK-C.

NutriBullet 600 Essentials Kit

For NutriBullet 600 Essentials Kit with its extractor-blade cup, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 600 Essentials Kit: product code (SKU) NBR-0807AW.

NutriBullet Ultra 1200 McLaren / Club Pack

For NutriBullet Ultra 1200 McLaren NB07500-1206GO-MC, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Ultra 1200 McLaren / Club Pack: product code (SKU) NB07500-1206GO-MC, NB07500-1214S.

NutriBullet Ultra 1200 Premium

For NutriBullet Ultra 1200 Premium, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup onto the base and touch the solid circle to blend, then wait for the blades to stop before unlocking and removing it.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
5. Let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
6. The automatic blend stops after 30 seconds; do not blend continuously for more than one minute, and let the contents settle for 10–15 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Ultra 1200 Premium: product code (SKU) NB07500-1208.

NutriBullet Triple Prep System

Wash the removable parts, fit and fill your chosen cup, pitcher or work bowl, lock the assembly onto the base, then connect power and select a control for that attachment.

1. Before first use, hand-wash, rinse and dry the removable parts, handling blades and discs by their plastic centres and cleaning the extractor blade with a small brush or sponge.
2. Set the unplugged base on a clean, dry, level surface and check that the chosen vessel, blade and gasket are undamaged.
3. For the pitcher, add ingredients below MAX, press the lid firmly into place with its spout closed, lock the vented cap, then turn the pitcher clockwise onto the base until it clicks.
4. For the cup, add food and sufficient liquid below MAX, screw the extractor blade on tightly, invert the cup and turn it clockwise onto the base until it clicks.
5. For a chopping or dough bowl, push the blade adapter onto the centre shaft and fit the chosen blade before adding prepared food below MAX.
6. For slicing or shredding, fit the adapter and place the disc in its upper operating position with the desired face up and its alignment marks matched.
7. Lock the work bowl clockwise onto the base, then turn its lid clockwise until the arrows align and insert the food pusher.

Next steps

1. Plug in and select a manual speed or a program displayed for the fitted attachment.
2. For dough, pulse to mix the wet and dry ingredients, then choose Dough or Low when dough begins to form.
3. For slicing or shredding, start on High before gently feeding food through the chute with the supplied food pusher.
4. To finish blending, press POWER and wait until the blade stops, unplug, then turn the cup or pitcher anticlockwise to remove it.
5. To finish processing, press POWER and unplug, wait until the blade or disc stops, unlock the lid anticlockwise before unlocking the bowl, and remove the blade or disc by its plastic section before emptying.
6. Keep cup blending and a continuously held Pulse within one minute, and allow cup contents to settle for 10–15 minutes before another cycle.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Triple Prep System: model number NBP-200; product code (SKU) NBKS07100.

NutriBullet Blender Combo 1200

Wash the removable parts, load and seal the pitcher or cup, lock it onto the base, then connect power and select the blending control for your attachment.

1. Before first use, hand-wash and dry the pitcher, lid, cups and other removable accessories, carefully cleaning the extractor blade without removing its gasket.
2. Set the unplugged base on a dry, level surface with clear ventilation space and check that the vessel and blade are undamaged.
3. For the pitcher, add food and liquid below the separate solids and liquid MAX lines, then fit the lid with its vented cap, place the pitcher handle to the right of the control panel and twist clockwise until it clicks.
4. For the cup, add ingredients and sufficient liquid below MAX, tightly screw on the extractor blade, then invert the sealed cup and twist it clockwise onto the base.
5. After assembly, plug in and press POWER, then LOW, MEDIUM, HIGH or EXTRACT.
6. Press Power to stop, wait until all blade movement stops, press Power again and unplug, then twist the vessel anticlockwise and lift it off.
7. Keep each continuous run within one minute.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Blender Combo 1200: model number NBC-12A; product code (SKU) NBF07500-1210DG, NBF07500-12C, NBF07500AK, NBF07500P.

NutriBullet SmartSense Blender — Australia

Wash the pitcher and tamper, fill and secure the pitcher, lock it onto the base, then connect power and choose a blending control.

1. With the unit unplugged, hand-wash the pitcher and tamper with soap and water before first use.
2. Set the base on a clean, dry, level surface and add ingredients with sufficient liquid below the pitcher’s liquid and solids MAX lines.
3. Snap on the lid with its vented cap, keeping the spout opposite the handle and the spout closed.
4. Face the pitcher handle toward the control panel and twist clockwise onto the base until it clicks.
5. Plug in and press Power, select a low speed with +/− and press the solid circle, or select AUTO.
6. Press the solid circle or AUTO again to stop and wait until the blades stop turning.
7. Press Power to switch off and unplug, then turn the pitcher anticlockwise and lift it off.

Cleaning and hot-ingredient guidance.

NutriBullet SmartSense Blender — Australia: model number NBF-14; product code (SKU) NBF07600.

NutriBullet SmartSense Blender Combo

Wash the pitcher and tamper, fill and secure the pitcher, lock it onto the base, then connect power and choose a blending control.

1. With the unit unplugged, hand-wash the pitcher and tamper with soap and water before first use.
2. Set the base on a clean, dry, level surface and add ingredients with sufficient liquid below the pitcher’s liquid and solids MAX lines.
3. Snap on the lid with its vented cap, keeping the spout opposite the handle and the spout closed.
4. Face the pitcher handle toward the control panel and twist clockwise onto the base until it clicks.
5. Plug in and press Power, select a low speed with +/− and press the solid circle, or select AUTO.
6. Press the solid circle or AUTO again to stop and wait until the blades stop turning.
7. Press Power to switch off and unplug, then turn the pitcher anticlockwise and lift it off.

Cleaning and hot-ingredient guidance.

NutriBullet SmartSense Blender Combo: model number NBF-14; product code (SKU) NBF07700-1507.

NutriBullet Smart Touch Blender Combo

Wash the removable parts, load and seal the pitcher or cup, lock it onto the base, then connect power and select the blending control for your attachment.

1. Before first use, hand-wash and dry the pitcher, lid, cups and other removable accessories, carefully cleaning the extractor blade without removing its gasket.
2. Set the unplugged base on a dry, level surface with clear ventilation space and check that the vessel and blade are undamaged.
3. For the pitcher, add food and liquid below the separate solids and liquid MAX lines, then press the lid firmly down, press and twist its cap into place, then twist the pitcher clockwise onto the base until it clicks.
4. For the cup, add ingredients and sufficient liquid below MAX, tightly screw on the extractor blade, then invert the sealed cup and twist it clockwise onto the base.
5. After assembly, plug in and press POWER, then a speed or blending program.
6. Press Power to stop, wait until all blade movement stops, press Power again and unplug, then twist the vessel anticlockwise and lift it off.
7. Do not run continuously for more than one minute.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Smart Touch Blender Combo: model number NBT-15; product code (SKU) NBF07520.

NutriBullet Power Core Blender

Wash the pitcher and lid, fill below MAX and secure the lid, lower the pitcher straight onto the base, then connect power and choose a speed or SMOOTHIE.

1. Before first use, wash the pitcher and lid with warm soapy water, rinse and dry them.
2. Set the unplugged base on a clean, dry, level surface and press its suction feet firmly down.
3. Add ingredients and sufficient liquid below the pitcher’s solids and liquid MAX lines.
4. Fit the lid and cap with the rear loop opposite the spout aligned to the handle.
5. Lower the pitcher straight onto the base with its studs aligned to the grooves until it clicks.
6. Plug in and press Power, followed by a speed or SMOOTHIE.
7. Press Power to stop, wait until the blades stop, press Power again and unplug before lifting off the pitcher.
8. Do not exceed one minute total of continuous or consecutive blending.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Power Core Blender: model number NBF-100S; product code (SKU) NBF07100.

NutriBullet Blender Combo 1000

Wash the removable parts, load and seal the pitcher or cup, lock it onto the base, then connect power and select the blending control for your attachment.

1. Before first use, hand-wash and dry the pitcher, lid, cups and other removable accessories, carefully cleaning the extractor blade without removing its gasket.
2. Set the unplugged base on a dry, level surface with clear ventilation space and check that the vessel and blade are undamaged.
3. For the pitcher, add food and liquid below the separate solids and liquid MAX lines, then fit the lid with its vented cap, place the pitcher handle to the right of the control panel and twist clockwise until it clicks.
4. For the cup, add ingredients and sufficient liquid below MAX, tightly screw on the extractor blade, then invert the sealed cup and twist it clockwise onto the base.
5. After assembly, plug in and press POWER, then LOW, HIGH or EXTRACT.
6. Press Power to stop, wait until all blade movement stops, press Power again and unplug, then twist the vessel anticlockwise and lift it off.
7. Limit continuous operation to one minute.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Blender Combo 1000: product code (SKU) NBF07500-1008DG.

NutriBullet Power Core Blender Combo

Wash the removable parts, load and seal the pitcher or cup, lock it onto the base, then connect power and select the blending control for your attachment.

1. Before first use, hand-wash and dry the pitcher, lid, cups and other removable accessories, carefully cleaning the extractor blade without removing its gasket.
2. Set the unplugged base on a dry, level surface with clear ventilation space and check that the vessel and blade are undamaged.
3. For the pitcher, add food and liquid below the separate solids and liquid MAX lines, then fit the lid with its spout opposite the handle and its interlock seated in the handle opening, then face the handle toward the control panel and twist the pitcher clockwise until it clicks.
4. For the cup, add ingredients and sufficient liquid below MAX, tightly screw on the extractor blade, then invert the sealed cup and twist it clockwise onto the base.
5. After assembly, plug in and press Power, then a speed or SMOOTHIE for the pitcher, or SMOOTHIE for the cup.
6. Press Power to stop, wait until all blade movement stops, press Power again and unplug, then twist the vessel anticlockwise and lift it off.
7. Keep cup blending within one minute, then allow contents to settle for 10–15 minutes and open the cooled cup slowly away from your body before another cycle.

Cleaning, blade replacement and hot-ingredient guidance.

NutriBullet Power Core Blender Combo: product code (SKU) NBF07200, NBF07202AK.

NutriBullet Power Core Plus

The full steps for this model are in its user guide.

Please use the instructions supplied with your exact model or chat with us for its assembly guide.

NutriBullet Power Core Plus: product code (SKU) NBF07200AKP.

NutriBullet Portable Blender / Portable Blender McLaren

Wash the removable cup and lid, charge the blender, fit and fill the cup below MAX, then lock the lid and press Power twice with a pause between presses.

1. With power off and the charger disconnected, wash and rinse the Cup and Lid with warm soapy water before first use.
2. Fully charge with the supplied USB-C cable and a suitable power supply, then disconnect the cable.
3. Set the Motor Base on a clean, dry, level surface and secure the Cup with the two dots aligned.
4. Add ingredients and sufficient liquid below MAX, twist on the Lid and put its latch upright in the locked position.
5. Press Power once to wake, wait about one second for the animation, then press Power again to start the 20-second cycle.
6. Press Power again to stop early and wait until the blades stop before lowering the latch and opening the drinking spout.
7. Keep continuous or consecutive blending within one minute total, carefully open the cooled container to release pressure before repeating, and do not exceed nine cycles in six minutes.

Cleaning and hot-ingredient guidance.

NutriBullet Portable Blender / Portable Blender McLaren: model number NBG-200, NBG-200S; product code (SKU) NB07400BB, NB07400BP, NB07400CB, NB07400EU, NB07400GO-MC, NB07400K, NB07400LB, NB07400LG, NB07400LGN, NB07400LM, NB07400LP, NB07400MA, NB07400NB, NB07400P, NB07400PA-MC, NB07400PLP, NB07400W, NB07400YE.

NutriBullet Flip Stainless

Wash the cup, charge the blender, fill and seal the cup with the motor assembly on top, then start the cycle and turn the blender over onto its base.

1. Before first use, hand-wash the Cup with warm soapy water and carefully clean the blade area with the supplied brush, keeping the motor assembly and charging port out of water. NEVER submerge the entire Motor Base, Blade, and Lid in water.
2. Charge for at least two hours with the supplied cable and power supply, then unplug and leave the blender undisturbed for 90 seconds to shut down before assembly.
3. Set the Cup upright on a level surface, add food and liquid above the minimum liquid mark and below MAX, then twist on the Motor Base, Blade, and Lid and snap the Flip-Top Lid closed.
4. With the motor assembly on top, press Power to wake, wait about one second for the white ring, then press Power again to begin the 30-second cycle.
5. Turn the blender over so its motor assembly is at the bottom and place it on a clean, dry, level surface.
6. Press Power to stop early, wait until the blades stop, then turn the motor assembly back to the top and slowly open the Flip-Top Lid away from your face and body.
7. Keep continuous or consecutive blending within one minute total.

Cleaning and hot-ingredient guidance.

NutriBullet Flip Stainless: model number NBG-300; product code (SKU) NBPB07350, NBPB07350AK, NBPB07350AW, NBPB07350BG, NBPB07350BGP, NBPB07350BV, NBPB07350EUC, NBPB07350IND, NBPB07350LP, NBPB07350PUR, NBPB07350YE.

NutriBullet Flip Tritan

Wash the cup, charge the blender, fill and seal the cup with the motor assembly on top, then start the cycle and turn the blender over onto its base.

1. Before first use, hand-wash the Cup with warm soapy water and carefully clean the blade area with the supplied brush, keeping the motor assembly and charging port out of water. NEVER submerge the entire Motor Base, Blade, and Lid in water.
2. Charge for at least two hours with the supplied cable and power supply, then unplug and leave the blender undisturbed for 90 seconds to shut down before assembly.
3. Set the Cup upright on a level surface, add food and liquid above the minimum liquid mark and below MAX, then twist on the Motor Base, Blade, and Lid and snap the Flip-Top Lid closed.
4. With the motor assembly on top, press Power to wake, wait about one second for the white ring, then press Power again to begin the 30-second cycle.
5. Turn the blender over so its motor assembly is at the bottom and place it on a clean, dry, level surface.
6. Press Power to stop early, wait until the blades stop, then turn the motor assembly back to the top and slowly open the Flip-Top Lid away from your face and body.
7. Keep continuous or consecutive blending within one minute total.

Cleaning and hot-ingredient guidance.

NutriBullet Flip Tritan: model number NBG-300; product code (SKU) NBPB07350T.

NutriBullet Flex Portable / Flex Portable McLaren

Wash the removable parts, charge the blender, fit the Blade Block and fill the cup, then lock the lid and cup onto the base and press Power to wake and start.

1. With power off and the charger disconnected, hand-wash the Cup, Blade Block and Sip Lid with warm soapy water, rinse and dry them before first use.
2. Fully charge using the supplied USB-C cable with a dry charging port, then disconnect the cable.
3. Insert the dry Blade Block blades-first through the Cup’s bottom opening and twist steadily to its built-in soft-stop without touching the blade edges.
4. Add ingredients and sufficient liquid below MAX, twist on the Sip Lid and close and lock the Sip Cap.
5. Set the base on a clean, dry, level surface and gently twist the Cup and Blade Block onto it until locked without forcing.
6. Press Power once, wait about one second for the animation and battery display, then press Power again to start a 30-second cycle.
7. Press Power to stop early and wait until the blades stop before gently twisting the cooled Cup off while gripping the Cup and Motor Base, without pushing down or gripping the Sip Lid.
8. Follow the important safeguard limit of one minute total for continuous or consecutive blending.

Cleaning.

NutriBullet Flex Portable / Flex Portable McLaren: model number NBG-400; product code (SKU) NBPB07222, NBPB07222AK, NBPB07222AW, NBPB07222BB, NBPB07222BMP, NBPB07222DB, NBPB07222EG, NBPB07222LLP, NBPB07222PA-MC, NBPB07222V, NBPB07222VB, NBPB07222WC.

NutriBullet GO

Wash the cup and cover, charge the blender, fill below MAX and screw on the motor base, then turn it upright and double-press Power to blend.

1. Before first use, wash the Cup and Cup Cover with warm soapy water and carefully clean the blade assembly.
2. Fully charge with the supplied USB cable until the charging light changes from red to blue.
3. Fill the Cup below MAX with prepared ingredients, leaving space at the top.
4. Hold the Motor Base from underneath, invert it over the Cup and turn clockwise to fasten.
5. Hold Power for three seconds until the flashing blue light confirms the cup is locked.
6. Turn the blender upright onto a dry, level surface and press Power twice quickly to start the 30-second cycle.
7. Press Power once to stop early and wait until the blades stop, then invert the blender and turn the Motor Base anticlockwise to remove it from the cooled cup.
8. Run no more than two consecutive cycles or one minute continuously.

Cleaning and hot-ingredient guidance.

NutriBullet GO: product code (SKU) NB07300, NB07300B, NB07300C, NB07300L, NB07300MA, NB07300R, NB07300S, NB07300TQ, NB07300W.

NutriBullet Juicer 800W

Wash the removable parts, fit the basin and sieve, lock the cover and position the pitcher, then start the motor before feeding produce with the pusher.

1. Before first use, hand-wash, rinse and dry the removable parts while unplugged, brushing the Sieve carefully without touching its sharp teeth.
2. With power OFF, set the base on a clean, dry, level counter and lower the Pulp Basin onto it with the spout aligned to the dimpled side.
3. Hold the Sieve by its rim, align it with the drive coupling and press down until it clicks.
4. Fit the Basin Cover with its ears aligned and raise the Locking Handle into both ears until securely locked.
5. Swing the No-Drip Spout cover up, open the pitcher lid’s latch and angle the pitcher onto the spout before setting it flat.

Next steps

1. Wash and prepare produce, removing rind and hard pits and cutting pieces to fit the chute without force.
2. After assembly, plug in and turn the dial to LOW for softer produce or HIGH for harder produce before feeding produce.
3. Feed gradually with the Food Pusher, using gentle pressure and stopping to empty the pulp container when full.
4. Turn the dial OFF, wait until the Sieve stops and unplug before removing the pitcher or taking the juicer apart.
5. Do not exceed ten minutes continuously, then unplug and keep the motor off for 15 minutes before continuing.

Cleaning and juice storage.

NutriBullet Juicer 800W: model number NBJ-100; product code (SKU) NBJ07100.

NutriBullet Cold Press Slow Juicer

Wash the removable parts, fit the bowl, screen and auger, lock the cover and position the collection containers, then switch ON before feeding prepared produce.

1. Before first use, separate and hand-wash the removable parts with warm soapy water, rinse and dry them.
2. With power OFF and unplugged, check the pulp plug is seated under the Juice Bowl and lower the bowl securely onto the base.
3. Fit the Juicing Screen into the Rotating Bowl Brush and lower both into the bowl, then turn and press the Auger onto its centre axis until seated.
4. Align the cover’s unlocked symbol with the bowl arrow, then twist clockwise until the locked symbol aligns with the triangle.
5. Place the Juice Container and Pulp Container under their spouts and fit the Food Pusher.

Next steps

1. Wash and prepare produce, removing thick skin and hard pits and cutting it to fit the chute.
2. With assembly complete, plug in and switch ON, then feed gradually using the supplied Food Pusher.
3. To stop, switch OFF, wait until all movement stops and unplug before unlocking the cover anticlockwise or removing parts.
4. Stop after no more than 15 minutes of rapid or firm-pressure juicing and rest the motor for one minute between uses.

Cleaning and juice storage.

NutriBullet Cold Press Slow Juicer: model number NBJ-300; product code (SKU) NBJ07300.

NutriBullet Juicer Pro 1000W

Wash the removable parts, fit the basin and sieve, lock the cover and position the pitcher, then start the motor before feeding produce with the pusher.

1. Before first use, hand-wash, rinse and dry the removable parts while unplugged, brushing the Sieve carefully without touching its sharp teeth.
2. With power OFF, set the base on a clean, dry, level counter and lower the Pulp Basin onto it with the spout aligned to the dimpled side.
3. Hold the Sieve by its rim, align it with the drive coupling and press down until it clicks.
4. Fit the Basin Cover with its ears aligned and raise the Locking Handle into both ears until securely locked.
5. Swing the No-Drip Spout cover up, open the pitcher lid’s latch and angle the pitcher onto the spout before setting it flat.

Next steps

1. Wash and prepare produce, removing rind and hard pits and cutting pieces to fit the chute without force.
2. After assembly, plug in and press LOW, HIGH or TURBO for the selected produce before feeding produce.
3. Feed gradually with the Food Pusher, using gentle pressure and stopping to empty the pulp container when full.
4. Press the selected speed to stop, then press Power to turn off, wait until the Sieve stops and unplug before removing the pitcher or taking the juicer apart.
5. Do not exceed ten minutes continuously, then unplug and keep the motor off for 15 minutes before continuing.

Cleaning and juice storage.

NutriBullet Juicer Pro 1000W: model number NBJ-200; product code (SKU) NBJ07200.

NutriBullet Cold Press Batch Juicer

Wash the removable parts, fit the bowl and auger, lock the hopper and position the cups, then load the hopper, close its lid and turn ON.

1. Before first use, hand-wash, rinse and dry the removable parts with power off and the juicer unplugged.
2. Set the base on a dry, level counter with the dial OFF and lower the Juicing Bowl onto it with its spouts aligned to the notches.
3. Press the Auger firmly into the centre until it locks, then keep the Hopper Lid open while fitting the Hopper and turning it clockwise until the orange dot disappears.
4. Place the Juice Cup and Pulp Cup under their respective spouts and prepare produce by removing rind, hard pits and seeds and cutting it to fit.
5. Plug in, load the Hopper and close the Lid, then turn the dial ON.
6. Use only the supplied 2-in-1 Pusher and Scraper Tool to guide food gently, and open the Juice Spout Cover to drain juice into the cup.
7. When finished, close the spout cover, turn OFF, unplug and wait until the Auger stops before opening or removing the Hopper.

Cleaning and juice storage.

NutriBullet Cold Press Batch Juicer: model number NBJ-500; product code (SKU) NBJ07500AK.

NutriBullet CrispLite Air Fryer 6L

Wash and fit the tray and basket, add food with space above it, slide the basket into the base, then connect power, choose a program and press Start/Stop.

1. Before first use, wash the Cooking Basket and 3-in-1 Reversible Grill, Pizza, & Crisping Tray with hot soapy water and dry them.
2. Set the base on a clean, dry, level, heat-resistant surface with at least 200 mm ventilation space and a clear rear vent. NEVER submerge the main unit in water.
3. Fit the 3-in-1 Reversible Grill, Pizza, & Crisping Tray securely and level in the bottom of the basket.
4. Add food without overfilling, leaving at least 50 mm between the food and the basket top.
5. Slide the basket fully into the base, plug in and press Power.
6. Press Menu until the desired program flashes, then press Start/Stop to begin.
7. To turn food, press Start/Stop to pause, remove the basket by its handle, turn food with a utensil, then refit the basket and press Start/Stop to resume.
8. When the cycle finishes, wait for cooking to stop, remove food with a utensil, switch off and unplug, then let the appliance cool before removing parts for cleaning.

Cleaning guidance.

NutriBullet CrispLite Air Fryer 6L: model number NBA-300; product code (SKU) NBA07300.

NutriBullet XXL Digital Air Fryer 7L

Wash and fit the tray and basket, add food with space above it, slide the basket into the base, then connect power, choose a program and press Start/Stop.

1. Before first use, wash the Cooking Basket and Crisping Tray with hot soapy water and dry them.
2. Set the base on a clean, dry, level, heat-resistant surface with at least 200 mm ventilation space and a clear rear vent. NEVER submerge the main unit in water.
3. Fit the Crisping Tray securely and level in the bottom of the basket.
4. Add food without overfilling, leaving at least 50 mm between the food and the basket top.
5. Slide the basket fully into the base, plug in and press Power.
6. Press Menu until the desired program flashes, then press Start/Stop to begin.
7. To turn food, press Start/Stop to pause, remove the basket by its handle, turn food with a utensil, then refit the basket and press Start/Stop to resume.
8. When the cycle finishes, wait for cooking to stop, remove food with a utensil, switch off and unplug, then let the appliance cool before removing parts for cleaning.

Cleaning guidance.

NutriBullet XXL Digital Air Fryer 7L: model number NBA-100; product code (SKU) NBA07100, NBA07100KRG.

NutriBullet Twin Drawer Air Fryer

Wash and fit the trays and drawers, add food with space above it, slide both drawers into the base, then select the drawer, choose its mode and press Start/Stop.

1. Before first use, remove the inserts under each drawer, wash the Cooking Drawers and Crisping Trays in hot soapy water and dry them.
2. Set the base on a clean, dry, level, heat-resistant surface with at least 200 mm clearance. NEVER submerge the main unit in water.
3. Fit each tray securely and level in its drawer and add food with at least 50 mm space at the top.
4. Slide both drawers fully into the base and connect power.
5. Press L or R to select a drawer, or SYNC to use the same settings for both, then select the mode with Menu.
6. Adjust Time or Temperature with the selection buttons and +/− as needed, then press Start/Stop.
7. To turn food, pause with Start/Stop, remove the drawer by its handle, turn food with a utensil and refit the drawer before resuming.
8. At completion, wait for cooking to stop, remove food with a utensil, switch off and unplug, then allow cooling before removing trays.

Cleaning guidance.

NutriBullet Twin Drawer Air Fryer: model number NBA-200A; product code (SKU) NBA07200.

NutriBullet CrispLite Vision Air Fryer 8L

Wash and fit the tray and basket, add food with space above it, slide the basket into the base, then connect power, choose a program and press Start/Stop.

1. Before first use, wash the Cooking Basket and 3-in-1 Reversible Grill, Pizza, & Crisping Tray with hot soapy water and dry them.
2. Set the base on a clean, dry, level, heat-resistant surface with at least 200 mm ventilation space and a clear rear vent. NEVER submerge the main unit in water.
3. Fit the 3-in-1 Reversible Grill, Pizza, & Crisping Tray securely and level in the bottom of the basket.
4. Add food without overfilling, leaving at least 50 mm between the food and the basket top.
5. Slide the basket fully into the base, plug in and press Power.
6. Press Menu until the desired program flashes, then press Start/Stop to begin.
7. To turn food, press Start/Stop to pause, remove the basket by its handle, turn food with a utensil, then refit the basket and press Start/Stop to resume.
8. When the cycle finishes, wait for cooking to stop, remove food with a utensil, switch off and unplug, then let the appliance cool before removing parts for cleaning.

Cleaning guidance.

NutriBullet CrispLite Vision Air Fryer 8L: model number NBA-350; product code (SKU) NBA07350.

NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L

Wash and fit the trays and baskets, add food with space above it, slide the baskets into the base, then select a basket and program and press Start/Pause.

1. Before first use, wash and dry the Baskets, Crisping Trays and Wire Racks with hot soapy water.
2. Set the base on a clean, dry, level, heat-resistant surface with at least 200 mm behind it and attach the rear Cord Wrap/Wall Spacer. NEVER submerge the main unit in water.
3. Fit each tray securely and level, place a Wire Rack above it with handles upward if needed, and add food with at least 50 mm space at the top.
4. Slide the baskets fully into the base, plug in and press Power.
5. Select Upper Basket or Lower Basket, choose a program and adjust time or temperature as needed, then press Start/Pause.
6. For separate settings, program each basket individually and use SYNC if both should finish together.
7. Pause before removing a basket to turn food with a utensil, then refit it securely before resuming.
8. At completion, wait for cooking to stop, remove food with a utensil, hold Power to switch off and unplug, then let everything cool before removing trays or racks.

Cleaning guidance.

NutriBullet CrispLite Dual Stack / Stacked Air Fryer 9L: model number NBA-400; product code (SKU) NBA07400.

NutriBullet Immersion Blender 800W

Wash the detachable parts, lock the chosen attachment, prepare the food, then hold Low-speed (I) to run your NutriBullet Immersion Blender 800W and release it to stop.

1. Before first use, wash and dry the detachable parts with warm soapy water, keeping the motor body and chopping-bowl lid out of the wash.
2. With the motor unplugged, fit the attachment: push the motor body into the blending arm or assembled whisk holder and turn clockwise, or seat the chopper S-blade on its centre pin by holding the upper plastic part. NEVER submerge the main unit in water.
3. Add prepared food without exceeding MAX, leave at least 100mm of space at the top, and include liquid for blending or whisking.
4. For the chopper, turn its lid clockwise to lock, then push the motor body into the lid and turn clockwise until secured.
5. For the arm or whisk, hold the attachment upright in the mixture before connecting power or pressing a button.
6. Plug in and hold Low-speed (I) to start, keeping one hand on the motor body and one on the bowl when chopping.
7. Release the button to stop, wait until all movement stops before lifting the attachment, and unplug before detaching it.
8. Keep ordinary blends generally under one minute, whisk for no longer than two minutes, chop hard permitted foods for no longer than five seconds, and allow at least five minutes between uses.

See cleaning, ingredient safety and storage.

NutriBullet Immersion Blender 800W: model number NBI-100; product code (SKU) NBI07110.

NutriBullet EveryGrain Cooker

Wash the removable parts, measure grains and water into the Cooking Pot, seat the pot and close the lid, then choose a program and press Start/Stop on your NutriBullet EveryGrain Cooker.

1. Before first use, hand-wash the Cooking Pot and wash the Steaming Basket, Spatula and Measuring Scoop with warm soapy water.
2. Add grains first, then water using the supplied scoop and the matching pot markings, keeping everything below the highest pot line.
3. Keep within the grain limit: up to five scoops of rice or other grains, four of quinoa or oats, and no more than two of farro or barley.
4. Seat the clean Cooking Pot level on the heating plate inside the base, placing the base on a clean, dry, level surface. NEVER submerge the main unit in water.
5. If steaming, sit the food-filled Steaming Basket level inside the pot, using one supplied scoop of water in the pot when steaming without grains.

Next steps

1. Push the lid down until it clicks, connect the cord to the base and outlet, and press Power.
2. Select a grain program or Steam and press Start/Stop, setting the Steam time with the arrows first if using that program.
3. Press Start/Stop to stop or allow the program to finish, then use oven mitts for the hot pot or basket and unplug before removing parts after they have cooled.
4. Steam can be set for up to one hour, and the cooker automatically keeps food warm for up to three hours after cooking.

See cleaning, ingredient safety and storage.

NutriBullet EveryGrain Cooker: model number NGC-100; product code (SKU) NBG07100.

NutriBullet Food Processor

Wash the detachable parts, fit one blade or disc and prepare the food, lock the lid and bowl, then select LOW, HIGH or PULSE on your NutriBullet Food Processor.

1. Before first use, wash the detachable parts with warm soapy water, handling blades by their plastic centres.
2. With the base unplugged, press the Blade Adaptor onto the Work Bowl shaft and fit one cutting attachment.
3. Seat the chosen blade or disc correctly: push a chopping or dough blade to the bottom, align the Slice/Shred Disc markings in its higher operating position with the required side up, or align the Spiralizer Disc notches and turn FRONT towards the base front.
4. For chopping or dough, add prepared ingredients after fitting the blade without passing LIQUID MAX, or keep disc-processing food aside until the motor runs.
5. Turn the lid clockwise until its arrows align with the handle, insert the Food Pusher, and turn the lidded bowl clockwise onto the base until it clicks.

Next steps

1. Plug in and select LOW or HIGH for continuous processing or hold PULSE for a burst, using LOW for dough and HIGH for discs.
2. For a disc, feed the prepared pieces only after starting the motor, guiding them gently with the supplied Food Pusher.
3. Press OFF or release PULSE, wait for the blade to stop, unplug, and turn the bowl and lid counterclockwise to unlock before removing the blade by its plastic centre.
4. Run for no longer than one minute and wait at least one minute before another processing cycle.

See cleaning, ingredient safety and storage.

NutriBullet Food Processor: model number NBP-100; product code (SKU) NBP07100.

NutriBullet Chill

Wash the removable parts, freeze a prepared recipe in the Pint Cup, fit and lock the blade-and-cup assembly, then choose a dessert program and press Start/Stop on your NutriBullet Chill.

1. Before first use, wash the removable parts with warm soapy water and inspect the Pint Cup and Blade Block for damage.
2. Fill the Pint Cup between MIN FILL and MAX FILL with a prepared dessert recipe, snap on the lid and freeze level for at least 24 hours.
3. Remove the frozen cup and its lid and process within five minutes, keeping the Blade Shaft completely dry inside and out.
4. With power disconnected, fully retract the Blade Shaft until the blade touches the top of the Blade Block, then screw the Blade Block clockwise onto the cup.
5. Lower the inverted cup onto the base shaft-first, align its tabs with the notches, then press down and turn clockwise to lock.

Next steps

1. Connect power, select the dessert program and press Start/Stop, allowing the program to run through its normal pauses until it beeps.
2. To finish early, hold Start/Stop for two seconds to cancel, and wait for the blade to stop before holding Cup Release and turning the cup counterclockwise to remove it.
3. Unplug before removing the Blade Block, turning it counterclockwise and handling it by its plastic grip.
4. Programs take approximately three to four and a half minutes. The full steps for this model are in its user guide.

See cleaning, ingredient safety and storage.

NutriBullet Chill: model number NBD-100; product code (SKU) NBD07100AW, NBD07100CCP, NBD07100MCG.

NutriBullet Limitless Food Processor

Wash the detachable parts, fit one cutting attachment, load and lock the Work Bowl or Endless Chute, then slide the handle toggle to ON or hold PULSE on your NutriBullet Limitless Food Processor.

1. Before first use, wash the detachable parts with warm soapy water, holding sharp attachments by their plastic areas.
2. With power disconnected, fit the chosen attachment: seat the Chopping Blade on the Work Bowl adaptor, or fit the Slice/Shred Disc with the required side facing up.
3. For the Endless Chute instead, lock it clockwise onto the base, press the Slinger Disc into its bottom opening, fit the Slice/Shred Disc onto its stem and place a receiving bowl under the outlet.
4. For chopping, load prepared ingredients after fitting the blade and keep liquid at or below LIQUID MAX, or keep slicing and shredding food aside until the motor runs.
5. Lock the lid clockwise with its markings aligned to the handle, insert the Food Pusher, and lock the Work Bowl clockwise onto the base until it clicks if using that bowl.
6. Plug in and slide the toggle to ON or hold PULSE, feeding disc-processing food gently with the supplied Food Pusher after the motor starts.
7. Slide to OFF or release PULSE, wait until the blade or disc stops and unplug before unlocking the bowl and lid or handling the cutting attachment by its plastic grip.
8. The Endless Chute stops after 120 seconds; the guide gives food-specific processing times but no general maximum Work Bowl run time or timed cooling interval.

See cleaning, ingredient safety and storage.

NutriBullet Limitless Food Processor: model number NBP-300; product code (SKU) NBP07300.

NutriBullet Baby

Wash the parts, load and seal the Short Cup or assemble and fill the Batchbowl, then push down and twist clockwise to start your NutriBullet Baby and turn counterclockwise to stop.

1. Before first use, wash the cup or Batchbowl with warm soapy water and hand-wash the Extractor Blade without removing its seal.
2. For the Short Cup, add liquid and completely cooled, prepared food below MAX, then twist the Extractor Blade on until tightly sealed.
3. For the Batchbowl instead, twist the Extractor Blade onto the empty bowl first, add prepared food and liquid below MAX, then firmly fit its lid and cap.
4. Connect power and place the assembled vessel onto the base, then push down and twist clockwise to blend.
5. Turn counterclockwise to stop, wait until all moving parts have stopped before lifting the vessel off, and unplug before removing the blade.
6. Do not blend continuously for more than one minute.

See cleaning, ingredient safety and storage.

NutriBullet Baby: model number BB-101K; product code (SKU) NBY-1807.

NutriBullet Baby Steam + Blend

Wash the parts and run the initial cleaning cycle, load prepared food and water, lock the lid and bowl, then select a setting and press Power on your NutriBullet Baby Steam + Blend.

1. Before first use, wash and dry the blade, holder, Work Bowl and lid with warm soapy water, handling the blade by a non-sharp area.
2. With the base unplugged, lower the blade onto the bowl holder, turn the lid clockwise to lock, align the bowl arrow with Unlock and turn the bowl counterclockwise onto the base.
3. For the initial cleaning cycle, fill the reservoir to the 25-minute line, lock its cap clockwise, plug in, select Steam and press Power.
4. When that cycle finishes, unplug and let everything cool completely, then lift the blade vertically with a mitt and discard remaining water from the bowl and reservoir.
5. For a food batch, fill the cold reservoir to the food’s steaming-time marking and refit its cap before fitting the blade and loading prepared food below MAX and below the pour-spout vents.

Next steps

1. Lock the lid clockwise and bowl counterclockwise onto the base, then plug in and check for one beep and a steady blue light.
2. Select Steam, Blend or Steam + Blend and press Power, allowing the combined setting to steam and then blend automatically.
3. Press Power to stop early or wait for completion, then unplug and wait at least ten minutes and until the unit is fully cool and every moving part has stopped.
4. Turn the bowl clockwise to unlock, open the lid, lift the blade vertically with a mitt and remove the food with a non-metal spoon or spatula.
5. The standard Blend cycle runs for one minute, and food must be fully cooked and at a safe serving temperature before feeding.

See cleaning, ingredient safety and storage.

NutriBullet Baby Steam + Blend: model number NBY-200; product code (SKU) NBY07200.

Magic Bullet To Go 200W

Wash the cup and blade, fill below MAX and screw on the Cross Blade, then place the inverted cup onto the base and press down to blend.

1. Before first use, hand-wash the Cup and Cross Blade with soapy water, rinse and dry them without removing the blade gasket.
2. Place the base on a stable, dry, level surface and inspect the cup tabs, blade and gasket for damage.
3. Add ingredients and liquid below MAX and twist the Cross Blade tightly onto the cup.
4. Plug in, invert the sealed cup and align its tabs with those on the base, then press down to blend.
5. For hands-free blending, press down and turn clockwise until the tabs lock under the base lip.
6. Release pressure to stop, or twist anticlockwise out of lock-on mode, then wait until the blades stop before unplugging and lifting off the cup.
7. Do not run for more than one minute at a time.

Cleaning, blade replacement and hot-ingredient guidance.

Magic Bullet To Go 200W: model number MB1001B, MB1001S; product code (SKU) MBR-0307, MBR-0307AK.

Magic Bullet Value Pack 200W

Wash the cup and blade, fill below MAX and screw on the Cross Blade, then place the inverted cup onto the base and press down to blend.

1. Before first use, hand-wash the Cup and Cross Blade with soapy water, rinse and dry them without removing the blade gasket.
2. Place the base on a stable, dry, level surface and inspect the cup tabs, blade and gasket for damage.
3. Add ingredients and liquid below MAX and twist the Cross Blade tightly onto the cup.
4. Plug in, invert the sealed cup and align its tabs with those on the base, then press down to blend.
5. For hands-free blending, press down and turn clockwise until the tabs lock under the base lip.
6. Release pressure to stop, or twist anticlockwise out of lock-on mode, then wait until the blades stop before unplugging and lifting off the cup.
7. Do not run for more than one minute at a time.

Cleaning, blade replacement and hot-ingredient guidance.

Magic Bullet Value Pack 200W: model number MB1001B, MB1001S; product code (SKU) MBR-1107AK, MBR-1107GA, MBR-1107GFP, MBR-1107GHR, MBR-1107GUV, MBR-1107GW.

Magic Bullet Blender Combo

Wash the removable parts, fill and seal the cup or pitcher, lock it clockwise onto the base, then plug in and turn the dial to LOW or HIGH.

1. Before first use, wash, rinse and dry the cup, pitcher, removable blade, lids and accessories with soap and water.
2. Set the base on a clean, dry, level surface with the dial at HOME and check that the vessel, blade and gasket are undamaged.
3. For the cup, add ingredients and sufficient liquid below MAX, screw on the Cross Blade tightly, then invert the cup and twist clockwise onto the base until locked.
4. For the pitcher, tighten its removable blade anticlockwise onto the bottom, fill below MAX, firmly fit the lid and vented cap, then twist the pitcher clockwise onto the base.
5. Plug in and turn the dial left to LOW or right to HIGH, starting pitcher blends on LOW.
6. For pulses, leave the dial at HOME and hold PULSE, releasing it to stop.
7. To finish, turn to HOME, wait until the blades stop and unplug before unlocking the vessel anticlockwise.
8. After two consecutive cup cycles, wait 10–15 minutes before starting another.

Cleaning, blade replacement and hot-ingredient guidance.

Magic Bullet Blender Combo: model number MBF-100; product code (SKU) MBF07200AK.

Magic Bullet Mini Juicer

Wash the removable parts, fit the bowl and sieve, lock the cover and position the bin and cup, then switch ON before feeding produce with the pusher.

1. Before first use, hand-wash, rinse and dry the detachable parts, cleaning the Sieve with its brush without touching its teeth.
2. Set the unplugged base on a clean, dry, level surface, fit the Juice Bowl in its keyed position and press the Sieve onto the coupling until it clicks.
3. Fit the cover with the feed chute over the Sieve, then hook and snap both Locking Arms upright to secure it.
4. Fit the Pulp Bin onto the back until it clicks, insert the Food Pusher and point the Silicone Spout Cap down.
5. Fit the Juice Cup Lid and open its latch, then angle the cup so the spout sits just inside the lid hole before levelling it.

Next steps

1. Wash and prepare produce, removing rind, stems and hard pits and cutting pieces to fit the chute.
2. After checking the locks, bin and spout, plug in and press Power down to ON before feeding food gently with the Food Pusher.
3. Stop to empty the Pulp Bin when full or the Juice Cup when it reaches MAX.
4. Press Power up to OFF, wait until the Sieve stops and unplug before removing the cup or taking the juicer apart.

Cleaning and juice storage.

Magic Bullet Mini Juicer: model number MBJ-100; product code (SKU) MBJ07110, MBJ07110K.

Magic Bullet Kitchen Express 250W

Wash the removable parts, fit and fill the processing bowl or seal the blending cup, lock the assembly onto the base, then connect power and select ON or PULSE.

1. Before first use, wash, rinse and dry the cups, bowl, lid, pusher, blades and disc in warm soapy water.
2. Set the unplugged base on a stable, dry, level surface with the knob OFF.
3. For chopping, fit the chopping blade over the work-bowl shaft before adding prepared food below MAX.
4. For slicing or shredding, use the disc’s finger holes to fit the required side facing UP on the bowl shaft.
5. Lock the bowl lid clockwise, then place the bowl on the base and twist clockwise to lock it.

Next steps

1. For cup blending, add ingredients below MAX, screw the Cross Blade on tightly, invert the cup and twist it clockwise onto the base.
2. After assembly, plug in and select ON or hold PULSE, using ON and the supplied pusher when feeding the slicing or shredding disc.
3. Turn OFF, wait until the blade or disc stops and unplug before unlocking the vessel anticlockwise.
4. For the work bowl, unlock its lid anticlockwise and remove the blade or disc before emptying food.
5. Do not run the blender or processor for more than one minute at a time.

Cleaning, blade replacement and hot-ingredient guidance.

Magic Bullet Kitchen Express 250W: model number MB3001; product code (SKU) MB07200.

Magic Bullet Air Fryer 2.5L

Wash the pot and tray, preheat the fitted pot, add the tray and food, then refit the pot and set the temperature and timer to start cooking.

1. Before first use, wash the Fry Pot and Crisping Tray with hot soapy water and dry them.
2. Set the base on a clean, dry, flat surface with 250 mm behind it and 200 mm above and at its sides. NEVER submerge the main unit in water.
3. Fit the empty Fry Pot fully, plug into a wall outlet and preheat at the highest temperature for three minutes.
4. After frying action stops, remove the pot by its handle, fit the Crisping Tray securely and level, then add food with about 50 mm space at the top.
5. Push the pot fully into the base until it clicks and sits flush.
6. Set the Temperature Dial and turn the Timer clockwise to the required cooking time, turning past ten minutes then back for settings below ten minutes.
7. To stop early, turn the Timer fully anticlockwise and wait for frying action to stop before removing the pot by its handle.
8. Remove food with a utensil, turn both controls to zero and unplug, then let the appliance cool before removing the tray.

Cleaning guidance.

Magic Bullet Air Fryer 2.5L: product code (SKU) MBA07100.

NutriBullet Ultra Plus+ Compact Kitchen System

Wash the removable parts, fill and seal the blending cup or fit the processor or grinder attachment, lock it onto the base, then use the solid-circle cycle or dashed-circle pulses for that attachment.

1. Before first use, hand-wash, rinse and dry the removable parts for your attachment, keeping fingers clear of blade edges and fully drying the grinding cup and blade.
2. For the blending cup, add ingredients and liquid to the cup without going above the MAX line.
3. For the blending cup, twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. For the blending cup, set the base on a clean, dry, level surface, plug it in, invert the sealed cup and twist clockwise until it clicks, then touch the solid circle to start the automatic blend.
5. For the blending cup, let the automatic cycle stop or release the dashed-circle control if pulsing, wait until the motor and blades have completely stopped and the cup is cool, then twist anticlockwise, lift off the cup and unplug the base.
6. For the blending cup, the automatic blend stops after 30 seconds; do not exceed one minute of continuous blending or six consecutive 30-second intervals.

Next steps

1. For the blending cup, between repeat cycles, carefully open the cooled cup to release pressure before resealing it, and allow the contents to settle for 10–15 minutes after the last cycle.
2. For the processor, slide the work bowl over the Processor Base & Blade Adapter until flush, with its handle opposite the locking mechanism, then turn clockwise to lock.
3. For chopping, push the chopping blade onto the centre shaft before adding prepared food below MAX.
4. For slicing or shredding, fit the disc with the chosen face up and align its hash marks with the adapter so it sits nearly flush with the bowl rim.
5. With the bowl handle facing right, turn the assembled processor clockwise onto the unplugged base, then align the lid tab and arrows and push and twist the lid clockwise to lock.
6. Plug in and press the solid circle to start the 30-second processing cycle, using only the supplied food pusher to feed the disc after starting.

Next steps

1. Never use PULSE with the work bowl, and add liquid through the chute only with power off and the blades completely stopped.
2. After processing, stop and unplug, wait until the blade or disc stops, unlock the lid anticlockwise first and then unlock the bowl, removing the blade or disc by its plastic hub before emptying food.
3. For the grinder, open the grinding cup clockwise and add only dry or dehydrated ingredients below MAX.
4. Secure the grinding cup to its blade, place the assembly on the powered base and turn clockwise until it clicks.
5. Hold the dashed circle for short 1–2 second pulses and release it to stop, waiting until all movement stops before unlocking the grinder anticlockwise and lifting it off.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Ultra Plus+ Compact Kitchen System: model number NB-500; product code (SKU) NB07550-1206.

NutriBullet 600 Mega Pack

For NutriBullet 600 Mega Pack with its extractor-blade cup, wash the parts, fill the cup below MAX, twist on the extractor blade, invert it onto the base and press down and twist clockwise to blend, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup, lid and extractor blade with warm soapy water, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the extractor blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and gently press down and twist clockwise to start blending.
5. Gently press down and untwist anticlockwise to stop, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. Do not blend continuously for more than one minute.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet 600 Mega Pack: model number NB-101, NB-101S; product code (SKU) NBR-1107AK, NBR-1107EUC, NBR-1107IND, NBR-1107LAV, NBR-1107MAM, NBR-1107MAS, NBR-1107MASL, NBR-1107MT.

NutriBullet Turbo 1000 Deluxe Set

For NutriBullet Turbo 1000 Deluxe Set, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Turbo 1000 Deluxe Set: model number NB-400; product code (SKU) NBT07400-1008.

NutriBullet Turbo Ultimate Pack

For NutriBullet Turbo Ultimate Pack, wash the parts, fill the cup below MAX, twist on the Rapid Extractor Blade, lock the inverted cup clockwise onto the base to start, then untwist to stop and wait for the blades before lifting it off.

1. With the base unplugged, hand-wash the cup and lid with warm soapy water; wash the Rapid Extractor Blade on the top rack of the dishwasher (no heat or sanitise cycle) or by hand, then rinse and dry carefully.
2. Add cool, non-carbonated ingredients and liquid below the cup’s MAX line. Never put hot or fizzy ingredients in a sealed blending cup.
3. Twist the Rapid Extractor Blade onto the cup until tightly sealed.
4. Set the base on a clean, dry, level surface, plug it in, invert the sealed cup onto it and turn clockwise to lock and start the automatic blend.
5. Let the automatic cycle finish or twist the cup anticlockwise to stop early, wait until the motor and blades have completely stopped, then lift off the cup and unplug the base.
6. The automatic blend stops after 45 seconds; do not exceed three consecutive 45-second cycles, and let the contents settle for 10–20 minutes after multiple cycles.
7. Let a warm cup cool completely before opening it carefully away from your face and body. Never force open a warm, sealed cup.

Related: cleaning, blade care, storage and hot or fizzy ingredients.

NutriBullet Turbo Ultimate Pack: model number NB-400; product code (SKU) NBT07400-1009AK, NBT07400-1009SB, NBT07400-1009SG.

NutriBullet Juicer 800W 2.0

Wash the removable parts, fit the basin and sieve, lock the cover and position the pitcher, then start the motor before feeding produce with the pusher.

1. Before first use, hand-wash, rinse and dry the removable parts while unplugged, brushing the Sieve carefully without touching its sharp teeth.
2. With power OFF, set the base on a clean, dry, level counter and lower the Pulp Basin onto it with the spout aligned to the dimpled side.
3. Hold the Sieve by its rim, align it with the drive coupling and press down until it clicks.
4. Fit the Basin Cover with its ears aligned and raise the Locking Handle into both ears until securely locked.
5. Point the No-Drip Spout down, open the pitcher lid’s latch and angle the pitcher onto the spout before setting it flat.

Next steps

1. Wash and prepare produce, removing rind and hard pits and cutting pieces to fit the chute without force.
2. After assembly, plug in and align I or II on the Dial Ring with the white dot and press the centre Power Button before feeding produce.
3. Feed gradually with the Food Pusher, using gentle pressure and stopping to empty the pulp container when full.
4. Press the centre Power Button so it sits flush and the green ring disappears, wait until the Sieve stops and unplug before removing the pitcher or taking the juicer apart.

Cleaning and juice storage.

NutriBullet Juicer 800W 2.0: model number NBJ-100; product code (SKU) NBJ07150.